This work was supported by the National Institutes Health NIDCR [DE022664].

NOTE: The finished device is shown in Figure 2. The device enables pure uniaxial testing of specimens in a horizontal position.
1. Component Parts
<ol>
	<li>Prepare two programmable actuators with a 30 mm (1.2 in) travel per actuator capable of spanning 60 mm (2.3 in) when programmed to pull/push together. To accommodate a variety of potential uses, select actuators having a reasonable force capacity [67 N (15 lb)], peak thrust [58 N (13 lb)], speed resolution [0.9302 &#181;m/s (0.00004 in/s)], and a unidirectional accuracy [25 &#181;m (0.001 in)].</li>
	<li>Daisy-chain the actuators to sync them for an equal application of extension/retraction.</li>
	<li>Prepare a 24 V controller to provide the driving motion to the actuator; these systems enable a precise linear motion by the rotation of a screw, the leadscrew.</li>
	<li>Prepare two load cells with a maximum force capacity of 44.5 N (10 lb). Select a low profile or canister-style load which is ideal for confined spaces.</li>
	<li>Prepare the rail/carriage block system. Prepare one rail and two carriages; one to hold each actuator. Because steel will rust, select stainless-steel material if the device will be utilized for materials that require hydration; for all other purposes, steel is acceptable. 
	NOTE: An exploded view of the loading platform with the rail/carriage block shown in purple is provided in Figure 3.</li>
</ol>
2. Frame Construction
NOTE: For explanatory purposes, the platform is color-coded in the graphics.
<ol>
	<li>Prepare aluminum stock material. Select aluminum for its cost-effectiveness and ease of machining. Prepare both plate and &#39;L&#39;-shaped angle stock.</li>
	<li>Prepare stock material to machine fixtures. Select plexiglass; it is strong while lightweight.</li>
</ol>
3. Metal Base and Side Plate (Frame) Assembly
<ol>
	<li>Cut the base plate from the aluminum stock, making sure it is approximately 64 x 15 x 1.3 cm (25 x 6 x 0.5 in). Clean up the edges in the mill and cut the base plate to its final dimensions.</li>
	<li>Machine the plate flat in the mill, according to the specifications provided in the supplemental files.</li>
	<li>Face it, ensuring the plane is level.</li>
	<li>Machine a track into the base plate to align the side plates with a tolerance of 0.0126 mm (0.0005 in).</li>
	<li>Machine the side plates according to specifications provided in the supplemental files.</li>
	<li>Drill and tap the side plates on their bottom face.</li>
	<li>Mount the side plates upright in the track.</li>
	<li>Fasten the side plates to the base plate from underneath (Figure 4).</li>
</ol>
4. Attaching the Rail/Carriage Assembly to the Frame
<ol>
	<li>Machine tracks into the front face of each side plate to enable the mounting of the rail/carriage assembly according to the specifications provided in the drawing links (Figure 5).</li>
	<li>Fasten the rail to the track through the clearance holes in the rail via drilled and tapped holes (to accommodate #10-32 screws) in each side plate.</li>
</ol>
5. Rear Mount Attachment of the Actuators
<ol>
	<li>Machine rear mount attachments from the &#39;L&#39;-shaped angle stock according to the specifications provided in the supplemental files.</li>
	<li>Machine a bar to attach to the bottom of the mount to serve as a keyway and ride it in the machined track on the face of the side plate according to the specifications provided in the supplemental files. Screw the bar into the bottom of the mount.</li>
	<li>Drill a through hole in the base of the rear mount for the actuator clearance.</li>
	<li>Attach the rear mount to the body of the actuator via the hole pattern in the commercial actuator. 
	NOTE: One reason for making a rear mount is to eliminate the need to repeatedly attach the actuator directly to the frame using the small #2 metric screws that come stock on the actuators. The mount eliminates the concern of stripping the internal threads of the actuator with repeated use.</li>
	<li>Slot the base of the mount to attach the rear actuator mount to the frame via two screws.</li>
	<li>Drill and tap a series of holes (to accommodate #10-32 screws) flanking the track on the front face of the side plates to allow for an adjustable mount attachment if it is desirable to accommodate specimens of varying sizes.</li>
</ol>
6. Front Mount Attachment of the Actuators via Connectors
NOTE: The front mount is an &#39;L&#39;-shaped piece that attaches the front of the actuator to the carriage. The actuator does not physically contact the mount; it attaches via a series of connectors that extend from the actuator tip.
<ol>
	<li>Machine front mount attachments from the &#39;L&#39;-shaped angle stock according to the specifications provided in the supplemental files.</li>
	<li>Drill a hole in the base of the front mount to accommodate the tapered connector.</li>
	<li>Machine a track in the side of the front mount to accommodate a plate.</li>
	<li>Machine the plate with a track to accommodate the fixtures.</li>
	<li>Machine an aluminum, cylindrical connector according to the specifications provided in the drawing links. This adaptor connects the load cell to the actuator.</li>
	<li>Drill and tap the connector for a #2 metric screw on the actuator end and a #6 metric screw on the load cell end to support the axial mounting and alignment of the load cell and actuator.</li>
	<li>Repeat this process to machine two identical connectors, one for each load cell.</li>
	<li>Machine an aluminum, tapered, cylindrical connector according to specifications provided in the drawing links. This adaptor connects the load cell to the fixture and the carriage.</li>
	<li>Drill and tap the connector to the threaded load cell connection on one end.</li>
	<li>Pass the cylinder into the hole of the front actuator mount and use a set screw to anchor the cylinder end.</li>
	<li>Duplicate the system for the right and left actuators. 
	NOTE: As shown in Figure 6, once assembled, the base of the actuator is rigidly attached to the side plate. The front of the actuator is attached to the carriage and, as the actuator is extended and retracted, the carriage is pushed and pulled. This provides the framework for the fixture attachment and specimen loading.</li>
</ol>
7. Fixtures
<ol>
	<li>Machine the fixtures according to the specifications provided in the supplemental files (Figure 7).</li>
	<li>Machine a central, vertical slot in the fixture holder to accommodate the height.</li>
	<li>Attach the actuator front mounts to the rectangular plate with three drilled and tapped holes (to accommodate #10-32 screws) vertically aligned in the center of the plate.</li>
	<li>Raise or lower the holder as necessary, for example, if a saline bath for hydrated testing is being used, and secure it with screws.</li>
</ol>
8. Operating Procedure:
<ol>
	<li>Download the actuator software to remotely control the device16.</li>
	<li>Create a link between the computer and the 24 V controller with a 6-pin mini-din male-to-female PS/2 extension cable; each actuator controller has two 6-pin mini-din connector cable links.</li>
	<li>Use a USB-to-6-pin mini-din converter to connect the actuators to a standard computer; the converter contains one female 6-pin mini-din connector end and a USB connection port.</li>
	<li>Daisy-chain the actuators so that a single computer cable is sufficient for the operation, or alternatively, use an HDMI adapter in place of the USB adapter.</li>
	<li>Connect the actuators to the 24 V power supply.</li>
	<li>Once connected and powered, select the devices and customize the actuator performance.</li>
	<li>Alternatively, control the actuators manually by the dial on each actuator, which is useful for the set-up. 
	NOTE: This software is applicable to any standard operating system. With this software, the actuators can be moved at varying speeds to any set distance, synced at a set distance or synced to each other to move in unison.</li>
</ol>

<ol>
	<li>. ASTM E4-16. Standard practices for force verification of testing machines Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2016)</li><li>. ASTM E2309/E2309M-16. Standard practices for verification of displacement measuring systems and devices used in materials testing machines Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2016)</li><li>. ASTM E2428-15a. Standard practice for calibration and verification of torque transducers Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2015)</li><li>. ASTM E2624-17. Standard practice for torque calibration of testing machines Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2017)</li><li>. ASTM C39 &#8211; Standard test method for compressive strength of cylindrical concrete specimens Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2018)</li><li>. ASTM A370-17a. Standard test methods and definitions for mechanical testing of steel products Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2017)</li><li>. ASTM D4761-13. Standard test methods for mechanical properties of lumber and wood-base structural material Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2013)</li><li>Green, M. L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mechanical+properties+of+cheese,+cheese+analogues+and+protein+gels+in+relation+to+composition+and+microstructure.">Mechanical properties of cheese, cheese analogues and protein gels in relation to composition and microstructure.</a> Food Structure. 5 (1), 169-192 (1986).</li><li>. ASTM D76/D76M-11. Standard specification for tensile testing machines for textiles Available from: <a target="_blank" href="https://www.astm.org/Standard/standards-and-publications.html">https://www.astm.org/Standard/standards-and-publications.html</a> (2011)</li><li>Papini, M., Zdero, R., Schemitsch, E. H., Zalzal, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+biomechanics+of+human+femurs+in+axial+and+torsional+loading:+comparison+of+finite+element+analysis,+human+cadaveric+femurs,+and+synthetic+femurs.">The biomechanics of human femurs in axial and torsional loading: comparison of finite element analysis, human cadaveric femurs, and synthetic femurs.</a> Journal of Biomechanical Engineering. 129 (1), 12-19 (2007).</li><li>Poulet, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Intermittent+applied+mechanical+loading+induces+subchondral+bone+thickening+that+may+be+intensified+locally+by+contiguous+articular+cartilage+lesions.">Intermittent applied mechanical loading induces subchondral bone thickening that may be intensified locally by contiguous articular cartilage lesions.</a> Osteoarthritis and Cartilage. 23 (6), 940-948 (2015).</li><li>Li, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Osteoblasts+subjected+to+mechanical+strain+inhibit+osteoclastic+differentiation+and+bone+resorption+in+a+co-culture+system.">Osteoblasts subjected to mechanical strain inhibit osteoclastic differentiation and bone resorption in a co-culture system.</a> Annals of Biomedical Engineering. 41 (10), 2056-2066 (2013).</li><li>Huang, A. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+and+use+of+a+novel+bioreactor+for+regeneration+of+biaxially+stretched+tissue-engineered+vessels.">Design and use of a novel bioreactor for regeneration of biaxially stretched tissue-engineered vessels.</a> Tissue Engineering. Part C, Methods. 21 (8), 841-851 (2015).</li><li>Keyes, J. T., Haskett, D. G., Utzinger, U., Azhar, M., Van de Geest, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adaptation+of+a+planar+microbiaxial+optomechanical+device+for+the+tubular+biaxial+microstructural+and+macroscopic+characterization+of+small+vascular+tissues.">Adaptation of a planar microbiaxial optomechanical device for the tubular biaxial microstructural and macroscopic characterization of small vascular tissues.</a> Journal of Biomechanical Engineering. 133 (7), 075001 (2011).</li><li>Brown, T. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Techniques+for+mechanical+stimulation+of+cells+in+vitro:+A+review.">Techniques for mechanical stimulation of cells in vitro: A review.</a> Journal of Biomechanics. 33 (1), 3-14 (2000).</li><li>. Zaber Console software download Available from: <a target="_blank" href="https://www.zaber.com/zaber-software">https://www.zaber.com/zaber-software</a> (2018)</li><li>King, J. D., York, S. L., Saunders, M. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design,+fabrication+and+characterization+of+a+pure+uniaxial+microloading+system+for+biologic+testing.">Design, fabrication and characterization of a pure uniaxial microloading system for biologic testing.</a> Medical Engineering and Physics. 38 (4), 411-416 (2016).</li><li>Saunders, M. M., Donahue, H. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+a+cost-effective+loading+machine+for+biomechanical+evaluation+of+mouse+transgenic+models.">Development of a cost-effective loading machine for biomechanical evaluation of mouse transgenic models.</a> Medical Engineering and Physics. 26 (7), 595-603 (2004).</li></ol>

The authors have nothing to disclose.

The goal of this work was to design and fabricate a cost-effective and reliable uniaxial loader for its use with small-scale specimens such as tissue and fibers. A device was constructed that met the requirements set forth while also being flexible enough in design to allow for new attachments to be fabricated as the user needs grow. For example, the device will allow for the testing of dry and wet specimens in a uniaxial or fixed-end configuration.
Critical steps in the design and fabrication...

Mechanical testing has an interesting history that can be traced back to hardness testing equipment developed by Stanley Rockwell in the early in the twentieth century. While technology has grown to the extent that standard, documented practices guide everything from the verification of machine performance to the guidelines for carrying out specific tests1,2,3,4. Today, mechanical tests are conducted on everything from building materials such as concrete, steel, and wood to food and textile products5,6,7,8,9. Given that the fields of biomedical engineering and, more specifically, biomechanics utilize mechanical testing, loading machines are commonplace in biomechanics labs.
Loading machines run the range of scale in biomechanics. As an example, larger loading machines can be used to conduct full-body impact studies or determine human femoral mechanical properties, while smaller loading machines can be used to test murine bones or stimulate cells10,11,12,13,14. Two types of loading machines are found in the testing laboratory; those that are purchased commercially and those that are built by the user. Loading machines developed in-house are often favored for their personalization and customization options15.
In testing, a specimen is secured in the machine so that a displacement can be applied, generating a measurable force. If the load is used as the driving feedback, the test is load-controlled; if the displacement is used as the driving feedback, the test is displacement-controlled. Loading machines, in general, are built upon a frame that connects a mover to a fixed support. As such, testing generally involves one end of the specimen being moved while the other end remains fixed.
Shown in Figure 1 is a sketch of a simple loading machine demonstrating its basic components. Fundamental to all loading machines is a base or frame. Whereas the vast majority of commercial brands utilize a fixed base, the drawing depicts a platform that allows planar (XY) movement. The mover, in this case, is the upper arm that holds a load cell and is driven by a stepper motor. Attached to the frame are the fixtures which hold the specimen and dictate the type of test that is run. Shown in the drawing are three-point bend fixtures. The top fixture (the single contact) is mounted to the moving arm; the bottom fixture (the double contact) is mounted to the stationary base. During testing, the motor drives the upper fixture downward to where the center contact engages the specimen. As the contact engages the specimen, the load cell records the increase in resistance or the force placed upon the specimen.
There are occasions where machines are designed and built in-house to accomplish a motion not attainable with the existing machines in the laboratory. Here we describe in detail one such device. It is a loading platform that enables pure uniaxial specimen loading or equal and opposite motion at both ends. The device incorporates commercial load cells and actuators (movers); a frame is machined to hold the commercial parts and loading fixtures for specimen testing. Understanding the basic principles of testing machine construction can aid in the design of one&#39;s own machine. We have provided the drawing files we created as a starting point to assist researchers with their own machine development. The video will focus on the assembly of the device and the application of mechanical design principles to ensure alignment and reliable testing.

<table border="0" cellpadding="0" cellspacing="0" width="590">
	<tbody>
		<tr height="63">
			<td height="63" style="height:63px;width:216px;">Power supply, 24 V DC 2.5 A out, 100-240 V AC in, plug for North America&#160;</td>
			<td style="width:88px;">Zaber Technologies inc</td>
			<td style="width:119px;">PS05-24V25</td>
			<td style="width:167px;"></td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:216px;">6 pin mini din-male to female PS/2 extension cable</td>
			<td style="width:88px;">Zaber Technologies inc</td>
			<td style="width:119px;">T-DC06</td>
			<td></td>
		</tr>
		<tr height="65">
			<td height="65" style="height:65px;width:216px;">Stepper motor controller, 2 phase</td>
			<td style="width:88px;">Zaber Technologies inc</td>
			<td style="width:119px;">A-MCA</td>
			<td style="width:167px;"></td>
		</tr>
		<tr height="60">
			<td height="60" style="height:60px;width:216px;">Linear actuator, NEMA size 11, 30 mm travel, 58 N maximum continuous thrust</td>
			<td style="width:88px;">Zaber Technologies inc</td>
			<td>NA11B30</td>
			<td></td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:216px;">Corrosion resistant maintenance-Free Ball Bearing Carriages and Guide Rails</td>
			<td style="width:88px;">McMaster-Carr</td>
			<td>9184T31</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">6061-t6 Aluminum Stock</td>
			<td style="width:88px;">McMaster-Carr</td>
			<td style="width:119px;">NA</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">Plexiglas Stock</td>
			<td style="width:88px;">McMaster-Carr</td>
			<td style="width:119px;">NA</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:216px;">Canister load cell, 4.5N</td>
			<td style="width:88px;">Honeywell Sensotec</td>
			<td style="width:119px;">NA</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">USB to 6 pin mini-din</td>
			<td style="width:88px;">Universal&#160;</td>
			<td style="width:119px;">NA</td>
			<td></td>
		</tr>
	</tbody>
</table>

application of design aspects in uniaxial loading machine development

In terms of accurate and precise mechanical testing, machines run the continuum. Whereas commercial platforms offer excellent accuracy, they can be cost-prohibitive, often priced in the $100,000 - $200,000 price range. At the other extreme are stand-alone manual devices that often lack repeatability and accuracy (e.g., a manual crank device). However, if a single use is indicated, it is over-engineering to design and machine something overly elaborate. Nonetheless, there are occasions where machines are designed and built in-house to accomplish a motion not attainable with the existing machines in the laboratory. Described in detail here is one such device. It is a loading platform that enables pure uniaxial loading. Standard loading machines typically are biaxial in that linear loading occurs along the axis and rotary loading occurs about the axis. During testing with these machines, a load is applied to one end of the specimen while the other end remains fixed. These systems are not capable of conducting pure axial testing in which tension/compression is applied equally to the specimen ends. The platform developed in this paper enables the equal and opposite loading of specimens. While it can be used for compression, here the focus is on its use in pure tensile loading. The device incorporates commercial load cells and actuators (movers) and, as is the case with machines built in-house, a frame is machined to hold the commercial parts and fixtures for testing.

In order to verify the use of the system, actuator speed and performance tests were conducted17. These tests consisted of measuring the actuator speed and distance in comparison to the input values. To verify the sample travel distance accuracy, arbitrary travel distances along the shaft between 254 - 2540 &#181;m (0.01 - 0.10 in) were selected. The device was run to these distances and compared to the actual distance measured using combinations of gauge blocks and...

Watch this Scientific Journal Video about Application of Design Aspects in Uniaxial Loading Machine Development at JoVE.com

Application of Design Aspects in Uniaxial Loading Machine Development

Here we present a protocol to develop a pure uniaxial loading machine. Critical design aspects are employed to ensure accurate and reproducible testing results.

In terms of accurate and precise mechanical testing, machines run the continuum. Whereas commercial platforms offer excellent accuracy, they can be ...

application-of-design-aspects-in-uniaxial-loading-machine-development

Universidad de Cartagena UDEC

Research

Education

JoVE Journal

JoVE Core

Mechanical Engineering

Engineering

Unit 1

Analysis and Design of Beams for Bending

Structural Analysis

SCIENTISTS IN ACTION

5.8K Views.  University of Akron. Here we present a protocol to develop a pure uniaxial loading machine. Critical design aspects are employed to ensure accurate and reproducible testing results.

Video: Application of Design Aspects in Uniaxial Loading Machine Development

Atom Probe Tomography Studies on the Cu(In,Ga)Se2 Grain Boundaries

Compared with the existent techniques, atom probe tomography is a unique technique able to chemically characterize the internal interfaces at the nanoscale and in three dimensions. Indeed, APT possesses high sensitivity (in the order of ppm) and high spatial resolution (sub nm).
Considerable efforts were done here to prepare an APT tip which contains the desired grain boundary with a known structure. Indeed, site-specific sample preparation using combined focused-ion-beam, electron backscatter diffraction, and transmission electron microscopy is presented in this work. This method allows selected grain boundaries with a known structure and location in Cu(In,Ga)Se2 thin-films to be studied by atom probe tomography.
Finally, we discuss the advantages and drawbacks of using the atom probe tomography technique to study the grain boundaries in Cu(In,Ga)Se2 thin-film solar cells.

Atom Probe Tomography Studies on the CuIn,GaSe2 Grain Boundaries

In this work, we describe the use of the atom-probe tomography technique for studying the grain boundaries of the absorber layer in a CIGS solar cell. A novel approach to prepare the atom probe tips containing the desired grain boundary with a known structure is also presented here.

Compared with the existent techniques, atom probe tomography is a unique technique able to chemically characterize the internal interfaces at the ...

High-resolution, High-speed, Three-dimensional Video Imaging with Digital Fringe Projection Techniques

Digital fringe projection (DFP) techniques provide dense 3D measurements of dynamically changing surfaces.&#160;Like the human eyes and brain, DFP uses triangulation between matching points in two views of the same scene at different angles to compute depth.&#160;However, unlike a stereo-based method, DFP uses a digital video projector to replace one of the cameras1. The projector rapidly projects a known sinusoidal pattern onto the subject, and the surface of the subject distorts these patterns in the camera&#8217;s field of view. Three distorted patterns (fringe images) from the camera can be used to compute the depth using triangulation.
Unlike other 3D measurement methods, DFP techniques lead to systems that tend to be faster, lower in equipment cost, more flexible, and easier to develop.&#160;DFP systems can also achieve the same measurement resolution as the camera.&#160;For this reason, DFP and other digital structured light techniques have recently been the focus of intense research (as summarized in1-5). Taking advantage of DFP, the graphics processing unit, and optimized algorithms, we have developed a system capable of 30&#160;Hz 3D video data acquisition, reconstruction, and display for over 300,000 measurement points per frame6,7.&#160;Binary defocusing DFP methods can achieve even greater speeds8.
Diverse applications can benefit from DFP techniques. Our collaborators have used our systems for facial function analysis9, facial animation10, cardiac mechanics studies11, and fluid surface measurements, but many other potential applications exist.&#160;This video will teach the fundamentals of DFP techniques and illustrate the design and operation of a binary defocusing DFP system.

This video describes the fundamentals of digital fringe projection techniques, which provide dense 3D measurements of dynamically changing surfaces.&#160;It also demonstrates the design and operation of a high-speed binary defocusing system based on these techniques.

Digital fringe projection (DFP) techniques provide dense 3D measurements of dynamically changing surfaces.&#160;Like the human eyes and brain, DFP uses ...

The Preparation of Electrohydrodynamic Bridges from Polar Dielectric Liquids

Horizontal and vertical liquid bridges are simple and powerful tools for exploring the interaction of high intensity electric fields (8-20 kV/cm) and polar dielectric liquids. These bridges are unique from capillary bridges in that they exhibit extensibility beyond a few millimeters, have complex bi-directional mass transfer patterns, and emit non-Planck infrared radiation. A number of common solvents can form such bridges as well as low conductivity solutions and colloidal suspensions. The macroscopic behavior is governed by electrohydrodynamics and provides a means of studying fluid flow phenomena without the presence of rigid walls. Prior to the onset of a liquid bridge several important phenomena can be observed including advancing meniscus height (electrowetting), bulk fluid circulation (the Sumoto effect), and the ejection of charged droplets (electrospray). The interaction between surface, polarization, and displacement forces can be directly examined by varying applied voltage and bridge length. The electric field, assisted by gravity, stabilizes the liquid bridge against Rayleigh-Plateau instabilities. Construction of basic apparatus for both vertical and horizontal orientation along with operational examples, including thermographic images, for three liquids (e.g., water, DMSO, and glycerol) is presented.

Horizontal and vertical electrohydrodynamic liquid bridges are simple and powerful tools for exploring the interaction of high intensity electric fields and polar dielectric liquids. The construction of basic apparatus and operational examples, including thermographic images, for three liquids (e.g., water, DMSO, and glycerol) is presented.

Horizontal and vertical liquid bridges are simple and powerful tools for exploring the interaction of high intensity electric fields (8-20 kV/cm) and ...

Measuring Spray Droplet Size from Agricultural Nozzles Using Laser Diffraction

When making an application of any crop protection material such as an herbicide or pesticide, the applicator uses a variety of skills and information to make an application so that the material reaches the target site (i.e., plant). Information critical in this process is the droplet size that a particular spray nozzle, spray pressure, and spray solution combination generates, as droplet size greatly influences product efficacy and how the spray moves through the environment. Researchers and product manufacturers commonly use laser diffraction equipment to measure the spray droplet size in laboratory wind tunnels. The work presented here describes methods used in making spray droplet size measurements with laser diffraction equipment for both ground and aerial application scenarios that can be used to ensure inter- and intra-laboratory precision while minimizing sampling bias associated with laser diffraction systems. Maintaining critical measurement distances and concurrent airflow throughout the testing process is key to this precision. Real time data quality analysis is also critical to preventing excess variation in the data or extraneous inclusion of erroneous data. Some limitations of this method include atypical spray nozzles, spray solutions or application conditions that result in spray streams that do not fully atomize within the measurement distances discussed. Successful adaption of this method can provide a highly efficient method for evaluation of the performance of agrochemical spray application nozzles under a variety of operational settings. Also discussed are potential experimental design considerations that can be included to enhance functionality of the data collected.

We present protocols to be used in the measurement of spray droplet size from agricultural nozzles used in both aerial and ground based agrochemical applications. These methods presented were developed to provide consistent and repeatable droplet size data both inter- and intra-laboratory, when using laser diffraction systems.

When making an application of any crop protection material such as an herbicide or pesticide, the applicator uses a variety of skills and information to ...

Optical Trap Loading of Dielectric Microparticles In Air

We demonstrate a method to trap a selected dielectric microparticle in air using radiation pressure from a single-beam gradient optical trap. Randomly scattered dielectric microparticles adhered to a glass substrate are momentarily detached using ultrasonic vibrations generated by a piezoelectric transducer (PZT). Then, the optical beam focused on a selected particle lifts it up to the optical trap while the vibrationally excited microparticles fall back to the substrate. A particle may be trapped at the nominal focus of the trapping beam or at a position above the focus (referred to here as the levitation position) where gravity provides the restoring force. After the measurement, the trapped particle can be placed at a desired position on the substrate in a controlled manner. 
In this protocol, an experimental procedure for selective optical trap loading in air is outlined. First, the experimental setup is briefly introduced. Second, the design and fabrication of a PZT holder and a sample enclosure are illustrated in detail. The optical trap loading of a selected microparticle is then demonstrated with step-by-step instructions including sample preparation, launching into the trap, and use of electrostatic force to excite particle motion in the trap and measure charge. Finally, we present recorded particle trajectories of Brownian and ballistic motions of a trapped microparticle in air. These trajectories can be used to measure stiffness or to verify optical alignment through time domain and frequency domain analysis. Selective trap loading enables optical tweezers to track a particle and its changes over repeated trap loadings in a reversible manner, thereby enabling studies of particle-surface interaction.

A protocol for launching and stably trapping selected dielectric microparticles in air is presented.

We demonstrate a method to trap a selected dielectric microparticle in air using radiation pressure from a single-beam gradient optical trap. Randomly ...

Visualizing Uniaxial-strain Manipulation of Antiferromagnetic Domains in Fe1+YTe Using a Spin-polarized Scanning Tunneling Microscope

The quest to understand correlated electronic systems has pushed the frontiers of experimental measurements toward the development of new experimental techniques and methodologies. Here we use a novel home-built uniaxial-strain device integrated into our variable temperature scanning tunneling microscope that enables us to controllably manipulate in-plane uniaxial strain in samples and probe their electronic response at the atomic scale. Using scanning tunneling microscopy (STM) with spin-polarization techniques, we visualize antiferromagnetic (AFM) domains and their atomic structure in Fe1+yTe samples, the parent compound of iron-based superconductors, and demonstrate how these domains respond to applied uniaxial strain. We observe the bidirectional AFM domains in the unstrained sample, with an average domain size of ~50-150 nm, to transition into a single unidirectional domain under applied uniaxial strain. The findings presented here open a new direction to utilize a valuable tuning parameter in STM, as well as other spectroscopic techniques, both for tuning the electronic properties as for inducing symmetry breaking in quantum material systems.

Visualizing Uniaxial-strain Manipulation of Antiferromagnetic Domains in Fe1+YTe Using a Spin-polarized Scanning Tunneling Microscope

Using uniaxial strain combined with spin-polarized scanning tunneling microscopy, we visualize and manipulate the antiferromagnetic domain structure of Fe1+yTe, the parent compound of iron-based superconductors.

The quest to understand correlated electronic systems has pushed the frontiers of experimental measurements toward the development of new experimental ...

Crack Monitoring in Resonance Fatigue Testing of Welded Specimens Using Digital Image Correlation

A procedure using digital image correlation (DIC) to detect cracks on welded specimens during fatigue tests on resonance testing machines is presented. It is intended as a practical and reproducible procedure to identify macroscopic cracks at an early stage and monitor crack propagation during fatigue tests. It consists of strain field measurements at the weld using DIC. Images are taken at fixed load cycle intervals. Cracks become visible in the computed strain field as elevated strains. This way, the whole width of a small-scale specimen can be monitored to detect where and when a crack initiates. Subsequently, it is possible to monitor the development of the crack length. Because the resulting images are saved, the results are verifiable and comparable. The procedure is limited to cracks initiating at the surface and is intended for fatigue tests under laboratory conditions. By visualizing the crack, the presented procedure allows direct observation of macrocracks from their formation until rupture of the specimen.

Digital image correlation is used in fatigue tests on a resonance testing machine to detect macroscopic cracks and monitor crack propagation in welded specimens. Cracks on the specimen surface become visible as increased strains.

A procedure using digital image correlation (DIC) to detect cracks on welded specimens during fatigue tests on resonance testing machines is presented. It ...

Evaluating Usability Aspects of a Mixed Reality Solution for Immersive Analytics in Industry 4.0 Scenarios

In medicine or industry, the analysis of high-dimensional data sets is increasingly required. However, available technical solutions are often complex to use. Therefore, new approaches like immersive analytics are welcome. Immersive analytics promise to experience high-dimensional data sets in a convenient manner for various user groups and data sets. Technically, virtual-reality devices are used to enable immersive analytics. In Industry 4.0, for example, scenarios like the identification of outliers or anomalies in high-dimensional data sets are pursued goals of immersive analytics. In this context, two important questions should be addressed for any developed technical solution on immersive analytics: First, is the technical solutions being helpful or not? Second, is the bodily experience of the technical solution positive or negative? The first question aims at the general feasibility of a technical solution, while the second one aims at the wearing comfort. Extant studies and protocols, which systematically address these questions are still rare. In this work, a study protocol is presented, which mainly investigates the usability for immersive analytics in Industry 4.0 scenarios. Specifically, the protocol is based on four pillars. First, it categorizes users based on previous experiences. Second, tasks are presented, which can be used to evaluate the feasibility of the technical solution. Third, measures are presented, which quantify the learning effect of a user. Fourth, a questionnaire&#160;evaluates the stress level when performing tasks. Based on these pillars, a technical setting was implemented that uses mixed reality smartglasses to apply the study protocol. The results of the conducted study show the applicability of the protocol on the one hand and the feasibility of immersive analytics in Industry 4.0 scenarios on the other. The presented protocol includes a discussion of discovered limitations.

This protocol delineates the technical setting of a developed mixed reality application that is used for immersive analytics. Based on this, measures are presented, which were used in a study to gain insights into usability aspects of the developed technical solution.

In medicine or industry, the analysis of high-dimensional data sets is increasingly required. However, available technical solutions are often complex to ...

Manufacturing, Control, and Performance Evaluation of a Gecko-Inspired Soft Robot

This protocol presents a method for manufacturing, control, and evaluation of the performance of a soft robot that can climb inclined flat surfaces with slopes of up to 84&#176;. The manufacturing method is valid for the fast pneunet bending actuators in general and might, therefore, be interesting for newcomers to the field of actuator manufacturing. The control of the robot is achieved by means of a pneumatic control box that can provide arbitrary pressures and can be built by only using purchased components, a laser cutter, and a soldering iron. For the walking performance of the robot, the pressure-angle calibration plays a crucial role. Therefore, a semi-automated method for the pressure-angle calibration is presented. At high inclines (&#62; 70&#176;), the robot can no longer reliably fix itself to the walking plane. Therefore, the gait pattern is modified to ensure that the feet can be fixed on the walking plane.

This protocol provides a detailed list of steps to be performed for the manufacturing, control and evaluation of the climbing performance of a gecko-inspired soft robot.

This protocol presents a method for manufacturing, control, and evaluation of the performance of a soft robot that can climb inclined flat surfaces with ...

Design and Development of a Three-Dimensionally Printed Microscope Mask Alignment Adapter for the Fabrication of Multilayer Microfluidic Devices

This project aims to develop an easy-to-use and cost-effective platform for the fabrication of precise, multilayer microfluidic devices, which typically can only be achieved using costly equipment in a clean room setting. The key part of the platform is a three dimensionally (3D) printed microscope mask alignment adapter (MMAA) compatible with regular optical microscopes and ultraviolet (UV) light exposure systems. The overall process of creating the device has been vastly simplified because of the work done to optimize the device design. The process entails finding the proper dimensions for the equipment available in the laboratory and 3D-printing the MMAA with the optimized specifications. Experimental results show that the optimized MMAA designed and manufactured by 3D printing performs well with a common microscope and light exposure system. Using a master mold prepared by the 3D-printed MMAA, the resulting microfluidic devices with multilayered structures contain alignment errors of &lt;10 &#181;m, which is sufficient for common microchips. Although human error through transportation of the device to the UV light exposure system can cause larger fabrication errors, the minimal errors achieved in this study are attainable with practice and care. Furthermore, the MMAA can be customized to fit any microscope and UV exposure system by making changes to the modeling file in the 3D printing system. This project provides smaller laboratories with a useful research tool as it only requires the use of equipment that is typically already available to laboratories that produce and use microfluidic devices. The following detailed protocol outlines the design and 3D printing process for the MMAA. In addition, the steps for procuring a multilayer master mold using the MMAA and producing poly(dimethylsiloxane) (PDMS) microfluidic chips is also described herein.

This project allows small laboratories to develop an easy-to-use platform for the fabrication of precise multilayer microfluidic devices. The platform consists of a three-dimensionally printed microscope mask alignment adapter using which multilayer microfluidic devices with alignment errors of &lt;10 &#181;m were achieved.

This project aims to develop an easy-to-use and cost-effective platform for the fabrication of precise, multilayer microfluidic devices, which typically ...

Application of Design Aspects in Uniaxial Loading Machine Development

Summary

Explore More Videos

Chapters in this video

Atom Probe Tomography Studies on the Cu(In,Ga)Se₂ Grain Boundaries