We thank the China Ministry of Science and Technology (2016YDF0600803) for the financial support.

1. Sample Preparation
<ol>
	<li>Cut a small tissue block (about 3 mm x 3 mm x 5 mm) from the plant sample (e.g., a poplar stem).</li>
	<li>Immerse the tissue in boiling deionized water for 30 min. Immediately transfer it to deionized water at room temperature (RT) for 30 min. Repeat this step until the tissue sinks to the bottom of the container, indicating that the air in tissue has been removed and that the tissue has softened. 
	Note: For the samples that sink to the bottom prior to this step, generally repeat this cycle 3-5 times.</li>
	<li>Prepare 20, 50, 70, 90% (v/v) aliquots of polyethylene glycol (PEG) in deionized water, as well as pure PEG, and keep the solutions at 65 &#176;C.</li>
	<li>Incubate the tissue in a series of graded PEG baths to displace the water and allow the PEG to infiltrate. 
	Note: Typically, PEG with a molecular weight 2,000 (PEG2000) is used for embedding.
	<ol>
		<li>Process the tissue with graded PEG in a drying oven as follows: (a) 20% PEG for 1 h, (b) 50% PEG for 1.5 h, (c) 70% PEG for 2 h, (d) 90% PEG for 2 h, and (e) 100% PEG for 10 h.</li>
	</ol>
	</li>
	<li>Pre-warm a cassette at 65 &#176;C in an oven. Pour the PEG containing the block into the cassette and then place the tissue block in a desired position using pre-warmed tweezers or needles.</li>
	<li>Slowly cool down the cassette and store the tissue at RT until use.</li>
	<li>Dissect the PEG block containing the target tissue into a small block (about 1 cm x 1 cm x 2 cm) using a sharp razor blade and mount it on the microtome.</li>
	<li>Cut thin sections from the PEG block (typically 3-10 &#181;m).</li>
	<li>Rinse the section with deionized water in a watch glass 10 times to remove the PEG from the tissue.</li>
	<li>Immerse the sections with toluene/ethanol (2:1, v/v) for 6 h to remove the extractives. Prepare the reaction liquid by mixing 65 mL of deionized water, 0.5 mL of acetic acid, and 0.6 g of sodium chlorite in a beaker. Add one section and 3 mL of reaction liquid to a 5 mL vial. Screw on the top of the vial.</li>
	<li>Heat the vial in water bath at 75 &#176;C for 2 h to remove the lignin of the tissue. Rinse the section with deionized water in a watch glass 10 times.</li>
	<li>Transfer the untreated/delignified section to a glass microscope slide. Unfold the section carefully using brushes or needles. Remove the extra deionized water with tissue paper.</li>
	<li>Immerse the section into D2O. Cover the sample with a glass cover slip. Seal the cover slip with nail polish to prevent the evaporation of the D2O.</li>
</ol>
2. Spectral Acquisition
<ol>
	<li>Open the instrument operating software of the confocal Raman microscope. Turn on the laser (wavelength = 532 nm), focus on the surface of the crystalline silicon with a 100X microscope objective, and click the calibration button to calibrate the instrument.</li>
	<li>Switch the instrument to the optical microscope mode and turn on the microscope lamp. Mount the microscope slide on the stage, with the cover slip facing the objective.</li>
	<li>View the sample with a 20X microscope objective and locate the area of interest. Apply immersion oil to the coverslip and switch to the immersion microscope objective (60X, numerical aperture NA = 1.35). Focus on the surface of the sample.</li>
	<li>Switch the instrument to the Raman testing mode and turn off the microscope lamp.</li>
	<li>Choose a mapping area by using a rectangular tool. Alter the step size to determine the number of obtained spectra. 
	Note: Be aware of the step size (usually larger than the spot diameter calculated by the numerical aperture of the objective; theoretically 1.22&#955;/NA). Sizes below this will result in oversampling.</li>
	<li>Set the optimum spectral parameters to obtain the best signal-to-noise ratio (SNR) and spectral quality in an appropriate acquisition time (generally &#60; 8 h), depending on the sample suitability. Generally, input the imaging parameters in the instrument software as follows: laser (532 nm), filter (100%), hole (300), slit (100), spectrometer (1,840 cm-1), grooves (1200t), objective (60X oil), and acquisition time (2 s).</li>
	<li>Save the spectral data before data processing and convert them to a universal format (e.g., TXT files).</li>
</ol>
3. Data Analysis
<ol>
	<li>Load the spectral data (TXT files) into the data analysis software (e.g., Matlab). Apply a noise-reduction technique on the data set to improve the SNR (e.g., the Savitzsky-Golay algorithm or the wavelet algorithm)</li>
	<li>Use untreated samples to produce the images of lignin and polysaccharides. For lignin imaging, consider the spectral peak around 1,600 cm-1 due to the aromatic ring symmetric stretching vibration. For polysaccharide imaging (including cellulose and hemicellulose), use the spectral peak around 2,889 cm-1 because of the CH and CH2 stretches.</li>
	<li>Use delignified samples to generate the images of cellulose and hemicellulose. Perform self-modeling curve resolution (SMCR) on the acquired spectra to discriminate the spectra of cellulose and hemicellulose and to image their distributions.</li>
	<li>Perform principal component analysis (PCA) and clustering analysis on the acquired data to distinguish the Raman spectra from different cell wall layers.</li>
</ol>

<ol>
	<li>Gonzalo, G. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bacterial+Enzymes+Involved+in+Lignin+Degradation.">Bacterial Enzymes Involved in Lignin Degradation.</a> J. Biotechnol. 236, 110-119 (2016).</li><li>Rosatella, A. A., Afonso, C. A. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chapter+2.">Chapter 2.</a> Ionic Liquids in the Biorefinery Concept: Challenges and Perspectives. , 38-64 (2016).</li><li>Sun, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Understanding+tissue+specific+compositions+of+bioenergy+feedstocks+Through+hyperspectral+Raman+imaging.">Understanding tissue specific compositions of bioenergy feedstocks Through hyperspectral Raman imaging.</a> Bio. 108 (2), 286-295 (2009).</li><li>Tolstik, T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Classification+and+prediction+of+HCC+tissues+by+Raman+imaging+with+identification+of+fatty+acids+as+potential+lipid+biomarkers.">Classification and prediction of HCC tissues by Raman imaging with identification of fatty acids as potential lipid biomarkers.</a> J. Cancer. Res. Clin. Oncol. 141 (3), 407-418 (2015).</li><li>Schrader, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Infrared and Raman spectroscopy: methods and applications. , (2008).</li><li>Gierlinger, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Imaging+of+plant+cell+walls+by+confocal+Raman+microscopy.">Imaging of plant cell walls by confocal Raman microscopy.</a> Nat. Protoc. 7 (9), 1694-1708 (2012).</li><li>Luca, A. C. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Online+fluorescence+suppression+in+modulated+Raman+spectroscopy.">Online fluorescence suppression in modulated Raman spectroscopy.</a> Anal. Chem. 82 (2), 738-745 (2009).</li><li>Schl&#252;cker, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Raman+microspectroscopy:+a+comparison+of+point,+line,+and+wide-field+imaging+methodologies.">Raman microspectroscopy: a comparison of point, line, and wide-field imaging methodologies.</a> Anal. Chem. 75 (16), 4312-4318 (2003).</li><li>Cooper, J. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chemometric+analysis+of+Raman+spectroscopic+data+for+process+control+applications.">Chemometric analysis of Raman spectroscopic data for process control applications.</a> Chemometr. Intell. Lab. Syst. 46 (2), 231-247 (1999).</li><li>Cheng, H. J., Hsiau, S. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+study+of+granular+agglomeration+mechanism.">The study of granular agglomeration mechanism.</a> Powder Technol. 199 (3), 272-283 (2010).</li><li>Zhang, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Method+for+removing+spectral+contaminants+to+improve+analysis+of+Raman+imaging+data.">Method for removing spectral contaminants to improve analysis of Raman imaging data.</a> Sci. Rep. 6, 39891 (2016).</li><li>Shinzawa, H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multivariate+data+analysis+for+Raman+spectroscopic+imaging.">Multivariate data analysis for Raman spectroscopic imaging.</a> J. Raman Spectrosc. 40 (12), 1720-1725 (2009).</li><li>Lawton, W. H., Sylvestre, E. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Self+modeling+curve+resolution.">Self modeling curve resolution.</a> Technometrics. 13, 617-633 (1971).</li><li>Zhang, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Method+for+automatically+identifying+spectra+of+different+wood+cell+wall+layers+in+Raman+imaging+data+set.">Method for automatically identifying spectra of different wood cell wall layers in Raman imaging data set.</a> Anal. Chem. 87 (2), 1344-1350 (2015).</li><li>Kudelski, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analytical+application+of+Raman+spectroscopy.">Analytical application of Raman spectroscopy.</a> Talanta. 76 (1), 1-8 (2008).</li></ol>

The authors have nothing to disclose.

The plant cell wall is a composite that is organized into several layers, including cell corner (CC), secondary wall (SW, with the S1, S2, and S3 layers), and compound middle lamella (CML, middle lamella plus the adjacent primary wall), which makes it difficult to obtain a flat surface during sample preparation. Thus, plant samples, especially grass, which has a more complicated structure than wood, often need to be solidified to allow for fine sectioning. PEG is an ideal hard matrix for cutting and Raman investigation, ...

Plant biomass is the most abundant renewable resource on Earth; is mainly composed of lignin, cellulose, and hemicellulose; and is considered an attractive source of bioenergy and bio-based chemicals1. Unfortunately, it can resist degradation and confer hydrolytic stability or structural robustness to the plant cell wall. Such resistance is attributable to the accessible surface area, biomass particle size, degree of polymerization, cellulose crystallinity, and protective lignin2. A comprehensive understanding of the structural and chemical nature of the plant cell wall is thus significant from the viewpoint of plant biology and chemistry, as well as from that of commercial utilization. Commonly used wet chemistry analyses, such as chromatography, mass spectrometry, and nuclear magnetic resonance spectroscopy, only provide average compositional data of the measured sample. Furthermore, these methods are invasive and destroy the original structure of the plant tissue3. 
The Raman imaging technique is a powerful tool for the nondestructive visualization of spatially resolved chemical information4. It uses a laser light to cause inelastic scattering with a photon and relies on changes in polarizability arising from the molecular vibrations. In this case, water causes weak Raman scattering, which makes this approach suitable for in situ investigations of biological samples5. The application of the Raman imaging technique to the plant cell wall can elucidate the structure and composition of plant cell walls in their native state, with the resolution on the scale of the single cell and even of the cell wall layers6. A typical Raman imaging analysis of a plant cell wall generally consists of three steps: 1) sample preparation, 2) spectral acquisition, and 3) data processing. 
Although one of the major advantages of Raman imaging is the ability to achieve label-free and non-destructive spectra with minimal sample preparation, physical sample sectioning is still necessary to expose the surface of interest. This process should be performed carefully to obtain a flat surface, since the technique depends on maintaining optical focus7. Spectral acquisition requires a balance between image quality and extensive acquisition times8. Data processing aims to effectively extract the chemical information from the image data, especially for the components with similar chemical structures, such as cellulose and hemicellulose. Due to the strong spectral overlap, the exact spectra are difficult to discern. In this case, multivariate analysis is a straightforward approach to effectively uncover the hiding structural and chemical information9. This work presents a general protocol describing the use of Raman imaging to visualize the main components in plant cell walls, including lignin, cellulose, and hemicellulose.

<table border="0" cellpadding="0" cellspacing="0" width="597">
	<tbody>
		<tr height="20">
			<td height="20" style="height:20px;width:199px;">Microtome</td>
			<td style="width:136px;">Thermo Scientific</td>
			<td style="width:199px;">Microm HM430</td>
			<td style="width:64px;"></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Confocal Raman microscope</td>
			<td>Horiba Jobin Yvon</td>
			<td>Xplora</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Oven</td>
			<td>Shanghai ZHICHENG</td>
			<td>ZXFD-A5040</td>
			<td></td>
		</tr>
	</tbody>
</table>

combining raman imaging and multivariate analysis to visualize lignin, cellulose, and hemicellulose in the plant cell wall

The application of Raman imaging to plant biomass is increasing because it can offer spatial and compositional information on aqueous solutions. The analysis does not usually require extensive sample preparation; structural and chemical information can be obtained without labeling. However, each Raman image contains thousands of spectra; this raises difficulties when extracting hidden information, especially for components with similar chemical structures. This work introduces a multivariate analysis to address this issue. The protocol establishes a general method to visualize the main components, including lignin, cellulose, and hemicellulose within the plant cell wall. In this protocol, procedures for sample preparation, spectral acquisition, and data processing are described. It is highly dependent upon operator skill at sample preparation and data analysis. By using this approach, a Raman investigation can be performed by a non-specialist user to acquire high-quality data and meaningful results for plant cell wall analysis.

Figure 1 presents an overview of a typical micro-Raman system for the Raman imaging of a plant cell wall. As an example, the original Raman spectra of poplar (Populus nigra L.) have significant baseline drifts and spikes (Figure 2a). After performing the automatic pre-processing method for Raman imaging data set (APRI), these two spectral contaminants are successfully removed (Figure 2b). A ...

Watch this Scientific Journal Video about Combining Raman Imaging and Multivariate Analysis to Visualize Lignin, Cellulose, and Hemicellulose in the Plant Cell Wall at JoVE.com

Combining Raman Imaging and Multivariate Analysis to Visualize Lignin, Cellulose, and Hemicellulose in the Plant Cell Wall

This protocol aims to present a general method to visualize lignin, cellulose, and hemicellulose in plant cell walls using Raman imaging and multivariate analysis.

The application of Raman imaging to plant biomass is increasing because it can offer spatial and compositional information on aqueous solutions. The ...

combining-raman-imaging-multivariate-analysis-to-visualize-lignin

Universidad de Cartagena UDEC

Research

JoVE Journal

Biochemistry

11.8K Views.  Beijing Forestry University. This protocol aims to present a general method to visualize lignin, cellulose, and hemicellulose in plant cell walls using Raman imaging and multivariate analysis. 

Video: Combining Raman Imaging and Multivariate Analysis to Visualize Lignin, Cellulose, and Hemicellulose in the Plant Cell Wall

Determination of the Glycogen Content in Cyanobacteria

Cyanobacteria accumulate glycogen as a major intracellular carbon and energy storage&#160;during photosynthesis. Recent developments in research have highlighted complex mechanisms of glycogen metabolism, including the diel cycle of biosynthesis and catabolism, redox regulation, and the involvement of non-coding RNA. At the same time, efforts are being made to redirect carbon from glycogen to desirable products in genetically engineered cyanobacteria to enhance product yields. Several methods are used to determine the glycogen contents in cyanobacteria, with variable accuracies and technical complexities. Here, we provide a detailed protocol for the reliable determination of the glycogen content in cyanobacteria that can be performed in a standard life science laboratory. The protocol entails the selective precipitation of glycogen from the cell lysate and the enzymatic depolymerization of glycogen to generate glucose monomers, which are detected by a glucose oxidase-peroxidase (GOD-POD) enzyme coupled assay. The method has been applied to Synechocystis sp. PCC 6803 and Synechococcus sp. PCC 7002, two model cyanobacterial species that are widely used in metabolic engineering. Moreover, the method successfully showed differences in the glycogen contents between the wildtype and mutants defective in regulatory elements or glycogen biosynthetic genes.

Here, we present a reliable and easy assay to measure the glycogen content in cyanobacterial cells. The procedure entails precipitation, selectable depolymerization, and the detection of glucose residues. This method is suitable for both wildtype and genetically engineered strains and can facilitate the metabolic engineering of cyanobacteria.

Cyanobacteria accumulate glycogen as a major intracellular carbon and energy storage&#160;during photosynthesis. Recent developments in research have ...

Structural Characterization of Mannan Cell Wall Polysaccharides in Plants Using PACE

Plant cell wall polysaccharides are notoriously difficult to analyze, and most methods require expensive equipment, skilled operators, and large amounts of purified material. Here, we describe a simple method for gaining detailed polysaccharide structural information, including resolution of structural isomers. For polysaccharide analysis by gel electrophoresis (PACE), plant cell wall material is hydrolyzed with glycosyl hydrolases specific to the polysaccharide of interest (e.g., mannanases for mannan). Large format polyacrylamide gels are then used to separate the released oligosaccharides, which have been fluorescently labeled. Gels can be visualized with a modified gel imaging system (see Table of Materials). The resulting oligosaccharide fingerprint can either be compared qualitatively or, with replication, quantitatively. Linkage and branching information can be established using additional glycosyl hydrolases (e.g., mannosidases and galactosidases). Whilst this protocol describes a method for analyzing glucomannan structure, it can be applied to any polysaccharide for which characterized glycosyl hydrolases exist. Alternatively, it can be used to characterize novel glycosyl hydrolases using defined polysaccharide substrates.

A protocol for the structural analysis of polysaccharides by gel electrophoresis (PACE), using mannan as an example, is described.

Plant cell wall polysaccharides are notoriously difficult to analyze, and most methods require expensive equipment, skilled operators, and large amounts ...

Isolation and Respiratory Measurements of Mitochondria from Arabidopsis thaliana

Mitochondria are essential organelles involved in numerous metabolic pathways in plants, most notably the production of adenosine triphosphate (ATP) from the oxidation of reduced compounds such as nicotinamide adenine dinucleotide (NADH) and flavin adenine dinucleotide (FADH2). The complete annotation of the Arabidopsis thaliana genome has established it as the most widely used plant model system, and thus the need to purify mitochondria from a variety of organs (leaf, root, or flower) is necessary to fully utilize the tools that are now available for Arabidopsis to study mitochondrial biology. Mitochondria are isolated by homogenization of the tissue using a variety of approaches, followed by a series of differential centrifugation steps producing a crude mitochondrial pellet that is further purified using continuous colloidal density gradient centrifugation. The colloidal density material is subsequently removed by multiple centrifugation steps. Starting from 100 g of fresh leaf tissue, 2 - 3 mg of mitochondria can be routinely obtained. Respiratory experiments on these mitochondria display typical rates of 100 - 250 nmol O2 min-1 mg total mitochondrial protein-1 (NADH-dependent rate) with the ability to use various substrates and inhibitors to determine which substrates are being oxidized and the capacity of the alternative and cytochrome terminal oxidases. This protocol describes an isolation method of mitochondria from Arabidopsis thaliana leaves using continuous colloidal density gradients and an efficient respiratory measurements of purified plant mitochondria.

Isolation and Respiratory Measurements of Mitochondria from Arabidopsis thaliana

As mitochondria are only a small percentage of the plant cell, they need to be purified for a range of studies. Mitochondria can be isolated from a variety of plant organs by homogenization, followed by differential and density gradient centrifugation to obtain a highly purified mitochondrial fraction.

Mitochondria are essential organelles involved in numerous metabolic pathways in plants, most notably the production of adenosine triphosphate (ATP) from ...

2 in 1: One-step Affinity Purification for the Parallel Analysis of Protein-Protein and Protein-Metabolite Complexes

Cellular processes are regulated by interactions between biological molecules such as proteins, metabolites, and nucleic acids. While the investigation of protein-protein interactions (PPI) is no novelty, experimental approaches aiming to characterize endogenous protein-metabolite interactions (PMI) constitute a rather recent development. Herein, we present a protocol that allows simultaneous characterization of the PPI and PMI of a protein of choice, referred to as bait. Our protocol was optimized for Arabidopsis cell cultures and combines affinity purification (AP) with mass spectrometry (MS)-based protein and metabolite detection. In short, transgenic Arabidopsis lines, expressing bait protein fused to an affinity tag, are first lysed to obtain a native cellular extract. Anti-tag antibodies are used to pull down protein and metabolite partners of the bait protein. The affinity-purified complexes are extracted using a one-step methyl tert-butyl ether (MTBE)/methanol/water method. Whilst metabolites separate into either the polar or the hydrophobic phase, proteins can be found in the pellet. Both metabolites and proteins are then analyzed by ultra-performance liquid chromatography-mass spectrometry (UPLC-MS or UPLC-MS/MS). Empty-vector (EV) control lines are used to exclude false positives. The major advantage of our protocol is that it enables identification of protein and metabolite partners of a target protein in parallel in near-physiological conditions (cellular lysate). The presented method is straightforward, fast, and can be easily adapted to biological systems other than plant cell cultures.

Protein-protein and protein-metabolite interactions are crucial for all cellular functions. Herein, we describe a protocol that allows parallel analysis of these interactions with a protein of choice. Our protocol was optimized for plant cell cultures and combines affinity purification with mass spectrometry-based protein and metabolite detection.

Cellular processes are regulated by interactions between biological molecules such as proteins, metabolites, and nucleic acids. While the investigation of ...

Using In Vitro Fluorescence Resonance Energy Transfer to Study the Dynamics Of Protein Complexes at a Millisecond Time Scale

Proteins are the primary operators of biological systems, and they usually interact with other macro- or small molecules to carry out their biological functions. Such interactions can be highly dynamic, meaning the interacting subunits are constantly associated and dissociated at certain rates. While measuring the binding affinity using techniques such as quantitative pull-down reveals the strength of the interaction, studying the binding kinetics provides insights on how fast the interaction occurs and how long each complex can exist. Furthermore, measuring the kinetics of an interaction in the presence of an additional factor, such as a protein exchange factor or a drug, helps reveal the mechanism by which the interaction is regulated by the other factor, providing important knowledge for the advancement of biological and medical research. Here, we describe a protocol for measuring the binding kinetics of a protein complex that has a high intrinsic association rate and can be dissociated quickly by another protein. The method uses fluorescence resonance energy transfer to report the formation of the protein complex in vitro, and it enables monitoring the fast association and dissociation of the complex in real time on a stopped-flow fluorimeter. Using this assay, the association and dissociation rate constants of the protein complex are quantified.

Protein-protein interactions are critical for biological systems, and studies of the binding kinetics provide insights into the dynamics and function of protein complexes. We describe a method that quantifies the kinetic parameters of a protein complex using fluorescence resonance energy transfer and the stopped-flow technique. &#160;

Proteins are the primary operators of biological systems, and they usually interact with other macro- or small molecules to carry out their biological ...

In Vivo Calcium Imaging in C. elegans Body Wall Muscles

The model organism C. elegans provides an excellent system to perform in vivo calcium imaging. Its transparent body and genetic manipulability allow for the targeted expression of genetically encoded calcium sensors. This protocol outlines the use of these sensors for the in vivo imaging of calcium dynamics in targeted cells, specifically the body wall muscles of the worms. By utilizing the co-expression of presynaptic channelrhodopsin, stimulation of acetylcholine release from excitatory motor neurons can be induced using blue light pulses, resulting in muscle depolarization and reproducible changes in cytoplasmic calcium levels. Two worm immobilization techniques are discussed with varying levels of difficulty. Comparison of these techniques demonstrates that both approaches preserve the physiology of the neuromuscular junction and allow for the reproducible quantification of calcium transients. By pairing optogenetics and functional calcium imaging, changes in postsynaptic calcium handling and homeostasis can be evaluated in a variety of mutant backgrounds. Data presented validates both immobilization techniques and specifically examines the roles of the C. elegans sarco(endo)plasmic reticular calcium ATPase and the calcium-activated BK potassium channel in the body wall muscle calcium regulation.

In Vivo Calcium Imaging in C. elegans Body Wall Muscles

This method provides a way to couple optogenetics and genetically encoded calcium sensors to image baseline cytosolic calcium levels and changes in evoked calcium transients in the body wall muscles of the model organism C. elegans.

The model organism C. elegans provides an excellent system to perform in vivo calcium imaging. Its transparent body and genetic manipulability allow for ...

Study on the Metabolism of Six Systemic Insecticides in a Newly Established Cell Suspension Culture Derived from Tea (Camellia Sinensis L.) Leaves

A platform for studying insecticide metabolism using in vitro tissues of tea plant was developed. Leaves from sterile tea plantlets were induced to form loose callus on Murashige and Skoog (MS) basal media with the plant hormones 2,4-dichlorophenoxyacetic acid (2,4-D, 1.0 mg L-1) and kinetin (KT, 0.1 mg L-1). Callus formed after 3 or 4 rounds of subculturing, each lasting 28 days. Loose callus (about 3 g) was then inoculated into B5 liquid media containing the same plant hormones and was cultured in a shaking incubator (120 rpm) in the dark at 25 &#177; 1 &#176;C. After 3&#8722;4 subcultures, a cell suspension derived from tea leaf was established at a subculture ratio ranging between 1:1 and 1:2 (suspension mother liquid: fresh medium). Using this platform, six insecticides (5 &#181;g mL-1 each thiamethoxam, imidacloprid, acetamiprid, imidaclothiz, dimethoate, and omethoate) were added into the tea leaf-derived cell suspension culture. The metabolism of the insecticides was tracked using liquid chromatography and gas chromatography. To validate the usefulness of the tea cell suspension culture, the metabolites of thiamethoxan and dimethoate present in treated cell cultures and intact plants were compared using mass spectrometry. In treated tea cell cultures, seven metabolites of thiamethoxan and two metabolites of dimethoate were found, while in treated intact plants, only two metabolites of thiamethoxam and one of dimethoate were found. The use of a cell suspension simplified the metabolic analysis compared to the use of intact tea plants, especially for a difficult matrix such as tea.

Study on the Metabolism of Six Systemic Insecticides in a Newly Established Cell Suspension Culture Derived from Tea Camellia Sinensis L. Leaves

This work presents a protocol for establishing a cell suspension culture derived from tea (Camellia sinensis L.) leaves that can be used to study the metabolism of external compounds that can be taken up by the whole plant, such as insecticides.

A platform for studying insecticide metabolism using in vitro tissues of tea plant was developed. Leaves from sterile tea plantlets were induced to form ...

Measuring Interactions between Fluorescent Probes and Lignin in Plant Sections by sFLIM Based on Native Autofluorescence

In lignocellulosic biomass (LB), the activity of enzymes is limited by the appearance of non-specific interactions with lignin during the hydrolysis process, which maintains enzymes far from their substrate. Characterization of these complex interactions is thus a challenge in complex substrates such as LB. The method here measures molecular interactions between fluorophore-tagged molecules and native autofluorescent lignin, to be revealed by F&#246;rster resonance energy transfer (FRET). Contrary to FRET measurements in living cells using two exogenous fluorophores, FRET measurements in plants using lignin is not trivial due to its complex autofluorescence. We have developed an original acquisition and analysis pipeline with correlated observation of two complementary properties of fluorescence: fluorescence emission and lifetime. sFLIM (spectral and fluorescent lifetime imaging microscopy) provides the quantification of these interactions with high sensitivity, revealing different interaction levels between biomolecules and lignin.

This protocol describes an original setup combining spectral and fluorescence lifetime measurements to evaluate F&#246;rster resonance energy transfer (FRET) between rhodamine-based fluorescent probes and lignin polymer directly in thick plant sections.

In lignocellulosic biomass (LB), the activity of enzymes is limited by the appearance of non-specific interactions with lignin during the hydrolysis ...

An Integrated Raman Spectroscopy and Mass Spectrometry Platform to Study Single-Cell Drug Uptake, Metabolism, and Effects

Cells are known to be inherently heterogeneous in their responses to drugs. Therefore, it is essential that single-cell heterogeneity is accounted for in drug discovery studies. This can be achieved by accurately measuring the plethora of cellular interactions between a cell and drug at the single-cell level (i.e., drug uptake, metabolism, and effect). This paper describes a single-cell Raman spectroscopy and mass spectrometry (MS) platform to monitor metabolic changes of cells in response to drugs. Using this platform, metabolic changes in response to the drug can be measured by Raman spectroscopy, while the drug and its metabolite can be quantified using mass spectrometry in the same cell. The results suggest that it is possible to access information about drug uptake, metabolism, and response at a single-cell level.

This protocol presents an integrated Raman spectroscopy-mass spectrometry (MS) platform that is capable of achieving single-cell resolution. Raman spectroscopy can be used to study cellular response to drugs, while MS can be used for targeted and quantitative analysis of drug uptake and metabolism.

Cells are known to be inherently heterogeneous in their responses to drugs. Therefore, it is essential that single-cell heterogeneity is accounted for in ...

RNA Blot Analysis for the Detection and Quantification of Plant MicroRNAs

MicroRNAs (miRNAs) are a class of endogenously expressed non-coding, ~21 nt small RNAs involved in the regulation of gene expression in both plants and animals. Most miRNAs act as negative switches of gene expression targeting key genes. In plants, primary miRNAs (pri-miRNAs) transcripts are generated by RNA polymerase II, and they form varying lengths of stable stem-loop structures called pre-miRNAs. An endonuclease, Dicer-like1, processes the pre-miRNAs into miRNA-miRNA* duplexes. One of the strands from miRNA-miRNA* duplex is selected and loaded onto Argonaute 1 protein or its homologs to mediate the cleavage of target mRNAs. Although miRNAs are key signaling molecules, their detection is often carried out by less than optimal PCR-based methods instead of a sensitive northern blot analysis. We describe a simple, reliable, and extremely sensitive northern method that is ideal for the quantification of miRNA levels with very high sensitivity, literally from any plant tissue. Additionally, this method can be used to confirm the size, stability and the abundance of miRNAs and their precursors.

This method demonstrates use of the northern hybridization technique to detect miRNAs from total RNA extract.

MicroRNAs (miRNAs) are a class of endogenously expressed non-coding, ~21 nt small RNAs involved in the regulation of gene expression in both plants and ...

Combining Raman Imaging and Multivariate Analysis to Visualize Lignin, Cellulose, and Hemicellulose in the Plant Cell Wall

Summary

Explore More Videos

Chapters in this video

Determination of the Glycogen Content in Cyanobacteria

Structural Characterization of Mannan Cell Wall Polysaccharides in Plants Using PACE

Isolation and Respiratory Measurements of Mitochondria from Arabidopsis thaliana

2 in 1: One-step Affinity Purification for the Parallel Analysis of Protein-Protein and Protein-Metabolite Complexes

Using In Vitro Fluorescence Resonance Energy Transfer to Study the Dynamics Of Protein Complexes at a Millisecond Time Scale

In Vivo Calcium Imaging in C. elegans Body Wall Muscles

Study on the Metabolism of Six Systemic Insecticides in a Newly Established Cell Suspension Culture Derived from Tea (Camellia Sinensis L.) Leaves

Measuring Interactions between Fluorescent Probes and Lignin in Plant Sections by sFLIM Based on Native Autofluorescence

An Integrated Raman Spectroscopy and Mass Spectrometry Platform to Study Single-Cell Drug Uptake, Metabolism, and Effects

RNA Blot Analysis for the Detection and Quantification of Plant MicroRNAs