The authors thank Destiny Garcia, Serena Ferraro, Erik Quiroz and Steven Kern (Advanced Composites Research, Engineering and Science laboratory) for their help in designing and manufacturing the test setup. Shawn Malone, Michael Akahori, David Kehlet (Engineering Fabrication Lab) are acknowledged for their suggestions and assistance in the machining process. The support of the National Science Foundation (collaborative grant CMMI-1265691 and its REU supplement) and the Office of Naval Research (N00014-13-1-0604 to A. Muliana, Texas &#38;M University (Principal Investigator), and V. La Saponara, managed by program director Yapa Rajapakse) are gratefully appreciated.

1. Loading the Specimens
<ol>
	<li>Raise the lid of the tank and rest it upon the side supports (Figure 4).</li>
	<li>Place the specimen in the U-bolt, and ensure that the cross bar is making contact at the center of the specimen.</li>
	<li>Rest the ends of the specimen on the aluminum supports hanging from the lid. The ends of the specimens should have 5-10 mm of overhang.</li>
	<li>Repeat steps 1.2-1.4 for all of the specimens that will be tested.</li>
	<li>Remove the lid supports, lower lid, and make sure that the lid is seated on the lip of the tank.</li>
	<li>Apply the desired force by adding weights to the steel rod next to the outer pulley.</li>
</ol>
2. Measuring Displacement
<ol>
	<li>Ensure that the string potentiometer line is pulled taut.</li>
	<li>Using a digital multimeter, measure the resistance across the outer pins of the potentiometer (Figure 3), with black to Pin 1 and red to Pin 3, and record the reading.</li>
	<li>Convert the resistance reading into a displacement reading by computing the calibration factor (in this case, 1 k&#8486; corresponds to a 64.895 mm displacement).</li>
	<li>Repeat steps 2.1-2.3 for each specimen.</li>
</ol>
3. Weighing the Specimens
<ol>
	<li>Before beginning the weighing procedure, record the displacement data and prepare an interim holding chamber filled with the testing fluid at RT, as per ASTM D522931, or the appropriate testing standard.</li>
	<li>Remove the slotted weights from the ends of the steel cables.</li>
	<li>Raise the lid of the tank and rest it upon the side supports.</li>
	<li>Remove the specimen and place it into the prepared interim holding chamber. Repeat this step for all of the specimens.</li>
	<li>Remove the specimens and dry them individually using a microfiber cloth in order to remove excess fluid.</li>
	<li>Place the specimen on a high-precision scale and record the data reading.</li>
	<li>Repeat steps 3.5-3.6 for all specimens and then follow Protocol Step 1.</li>
</ol>

<ol>
	<li>Katnam, K. B., Da Silva, L. F. M., Young, T. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bonded+repair+of+composite+aircraft+structures:+A+review+of+scientific+challenges+and+opportunities.">Bonded repair of composite aircraft structures: A review of scientific challenges and opportunities.</a> Prog Aerosp Sci. 61, 26-42 (2013).</li><li>Hollaway, L. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+review+of+the+present+and+future+utilization+of+FRP+composites+in+the+civil+infrastructure+with+reference+to+their+important+in-service+properties.">A review of the present and future utilization of FRP composites in the civil infrastructure with reference to their important in-service properties.</a> Constr Build Mater. 24, 2419-2445 (2010).</li><li>Mouritz, A. P., Gellert, E., Burchill, P., Challis, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Review+of+advanced+composite+structures+for+naval+ships+and+submarines.">Review of advanced composite structures for naval ships and submarines.</a> Compos Struct. 53, 21-41 (2001).</li><li>Albanilla, M. A., Li, Y., Karbhari, V. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Durability+characterization+of+wet+layup+graphite/epoxy+composites+used+in+external+strengthening.">Durability characterization of wet layup graphite/epoxy composites used in external strengthening.</a> Compos Part B-Eng. 37, 200-212 (2006).</li><li>Jedidi, J., Jacquemin, F., Vautrin, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Accelerated+hygrothermal+cyclical+tests+for+carbon/epoxy+laminates.">Accelerated hygrothermal cyclical tests for carbon/epoxy laminates.</a> Compos. Part A &#8211;Appl. Sci. 37, 636-645 (2006).</li><li>Jones, L. C., Tsao, A. K., Topoleski, L. D. T., N, E. l. i. a. z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Orthopedic+Implant+Retrieval+and+Failure+Analysis.">Orthopedic Implant Retrieval and Failure Analysis.</a> Degradation of Implant Materials. , 393-447 (2012).</li><li>Gellert, E. P., Turley, D. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Seawater+immersion+ageing+of+glass-fibre+reinforced+polymer+laminates+for+marine+applications.">Seawater immersion ageing of glass-fibre reinforced polymer laminates for marine applications.</a> Compos. Part A &#8211;Appl. Sci. 30, 1259-1265 (1999).</li><li>Sugita, Y., Winkelmann, C., La Saponara, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Environmental+and+chemical+degradation+of+carbon/epoxy+lap+joints+for+aerospace+applications,+and+effects+on+their+mechanical+performance.">Environmental and chemical degradation of carbon/epoxy lap joints for aerospace applications, and effects on their mechanical performance.</a> Compos. Sci. Technol. 70, 829-839 (2010).</li><li>Campbell, R. A., Pickett, B. M., La Saponara, V., Dierdorf, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Thermal+Characterization+and+Flammability+of+Structural+Epoxy+and+Carbon/Epoxy+Composite+with+Environmental+and+Chemical+Degradation.">Thermal Characterization and Flammability of Structural Epoxy and Carbon/Epoxy Composite with Environmental and Chemical Degradation.</a> J. Adhes. Sci. Technol. 26, 889-910 (2012).</li><li>Landry, B., LaPlante, G., LeBlanc, L. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Environmental+effects+on+mode+II+fatigue+delamination+growth+in+an+aerospace+grade+carbon/epoxy+composite.">Environmental effects on mode II fatigue delamination growth in an aerospace grade carbon/epoxy composite.</a> Compos. A-Appl. Sci. 43, 475-485 (2012).</li><li>Ferracane, J. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydroscopic+and+hydrolytic+effects+in+dental+polymer+networks.">Hydroscopic and hydrolytic effects in dental polymer networks.</a> Dent. Mater. 22, 211-222 (2006).</li><li>Mueller, Y., Tognini, R., Mayer, J., Virtanen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Anodized+titanium+and+stainless+steel+in+contact+with+CFRP:+An+electrochemical+approach+considering+galvanic+corrosion.">Anodized titanium and stainless steel in contact with CFRP: An electrochemical approach considering galvanic corrosion.</a> J. Biomed. Mater. Res. &#8211;A. 82, 936-946 (2007).</li><li>Bagley, E., Long, F. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-state+Sorption+and+Desorption+of+Organic+Vapors+in+Cellulose+Acetate.">Two-state Sorption and Desorption of Organic Vapors in Cellulose Acetate.</a> J. Am. Chem. Soc. 77, 2172-2178 (1955).</li><li>Shen, C. -. H., Springer, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Moisture+Absorption+and+Desorption+of+Composite+Materials.">Moisture Absorption and Desorption of Composite Materials.</a> J. Compos Mater. 10, 2-20 (1976).</li><li>Zhou, J., Lucas, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hygrothermal+effects+of+epoxy+resin.+Part+I:+the+nature+of+water+in+epoxy.">Hygrothermal effects of epoxy resin. Part I: the nature of water in epoxy.</a> Polymer. 40, 5505-5512 (1999).</li><li>Abot, J. L., Yasmin, A., Daniel, I. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hygroscopic+Behavior+of+Woven+Carbon-Epoxy+Composites.">Hygroscopic Behavior of Woven Carbon-Epoxy Composites.</a> J. Reinf. Plast. Comp. 24, 195-207 (2005).</li><li>LaPlante, G., Ouriadov, A. V., Lee-Sullivan, P., Balcom, B. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Anomalous+Moisture+Diffusion+in+an+Epoxy+Adhesive.">Anomalous Moisture Diffusion in an Epoxy Adhesive.</a> J. Appl. Polym. Sci. 109, 1350-1359 (2008).</li><li>Weitsman, Y. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Anomalous+fluid+sorption+in+polymeric+composites+and+its+relation+to+fluid-induced+damage.">Anomalous fluid sorption in polymeric composites and its relation to fluid-induced damage.</a> Compos. Part A &#8211;Appl. Sci. 37, 617-623 (2006).</li><li>Karbhari, V. M., Ghosh, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparative+durability+evaluation+of+ambient+temperature+cured+externally+CFRP+and+GFRP+composiste+systems+for+repair+of+bridges.">Comparative durability evaluation of ambient temperature cured externally CFRP and GFRP composiste systems for repair of bridges.</a> Compos. Part A &#8211;Appl. Sci. 40, 1353-1363 (2009).</li><li>Neumann, S., Marom, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Free-volume+dependent+moisture+diffusion+under+stress+in+composite+materials.">Free-volume dependent moisture diffusion under stress in composite materials.</a> J. Mater. Sci. 21, 26-30 (1986).</li><li>Wan, Y. Z., Wang, Y. L., Huang, Y., He, B. M., Han, K. Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hygrothermal+aging+behaviour+of+VARTMed+three-dimensional+braided+carbon-epoxy+composites+under+external+stresses.">Hygrothermal aging behaviour of VARTMed three-dimensional braided carbon-epoxy composites under external stresses.</a> Compos. Part A &#8211;Appl. Sci. 36, 1102-1109 (2005).</li><li>Helbling, C. S., Karbhari, V. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigation+of+the+Sorption+and+Tensile+Response+of+Pultruded+E-Glass/Vinylester+Composites+Subjected+to+Hygrothermal+Exposure+and+Sustained.">Investigation of the Sorption and Tensile Response of Pultruded E-Glass/Vinylester Composites Subjected to Hygrothermal Exposure and Sustained.</a> J. Reinf. Plast. Comp. 27, 613-638 (2008).</li><li>Kasturiarachchi, K. A., Pritchard, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Water+absorption+of+glass/epoxy+laminates+under+bending+stresses.">Water absorption of glass/epoxy laminates under bending stresses.</a> Composites. 14, 244-250 (1983).</li><li>Abdel-Magid, B., Ziaee, S., Gass, K., Schneider, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+combined+effects+of+load,+moisture+and+temperature+on+the+properties+of+E-glass/epoxy+composites.">The combined effects of load, moisture and temperature on the properties of E-glass/epoxy composites.</a> Compos Struct. 71, 320-326 (2005).</li><li>Ellyin, F., Rohrbarcher, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+Influence+of+Aqueous+Environment,+Temperature+and+Cyclic+Loading+on+Glass-Fibre/Epoxy+Composite+Laminates.">The Influence of Aqueous Environment, Temperature and Cyclic Loading on Glass-Fibre/Epoxy Composite Laminates.</a> J Reinf Plast Comp. 22, 615-636 (2003).</li><li>Earl, J. S., Dulieu-Barton, J. M., Shenoi, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Determination+of+hygrothermal+ageing+effects+in+sandwich+construction+joints+using+thermoelastic+stress+analysis.">Determination of hygrothermal ageing effects in sandwich construction joints using thermoelastic stress analysis.</a> Compos Sci Technol. 63, 211-223 (2003).</li><li>Jeon, J., Muliana, A., La Saponara, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Thermal+stress+and+deformation+analyses+in+fiber+reinforced+polymer+composites+undergoing+heat+conduction+and+mechanical+loading.">Thermal stress and deformation analyses in fiber reinforced polymer composites undergoing heat conduction and mechanical loading.</a> Compos. Struct. 111, 31-44 (2014).</li><li>Muliana, A. H., Rajagopal, K. R., Wineman, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+class+of+quasi-linear+models+for+describing+the+non-linear+viscoelastic+response+of+materials.">A new class of quasi-linear models for describing the non-linear viscoelastic response of materials.</a> Acta Mech. 224, 2169-2183 (2013).</li><li>Joshi, N., Muliana, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Deformation+in+Viscoelastic+Sandwich+Composites+Subject+to+Moisture+Diffusion.">Deformation in Viscoelastic Sandwich Composites Subject to Moisture Diffusion.</a> Compos. Struct. 92, 254-264 (2010).</li><li>Muliana, A. H., Sawant, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Viscoelastic+Responses+of+Polymer+Composites+with+Temperature+and+Time+Dependent+Constituents.">Viscoelastic Responses of Polymer Composites with Temperature and Time Dependent Constituents.</a> Acta Mech. 204, 155-173 (2009).</li><li>. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Standard+Test+Method+for+Moisture+Absorption+Properties+and+Equilibrium+Conditioning+of+Polymer.">Standard Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer.</a> Matrix Composite Materials. ASTM International. , (2004).</li></ol>

The authors have nothing to disclose.

From the acquired data, it can be seen that the concurrent testing scenario did affect the durability of the closed-cell polyurethane foam specimens. This can be seen by comparing the significantly different displacements (Figure 5) and residual loads to failure (Figure 6) of dry and wet specimens. Figure 7 shows pictures of the specimens after the residual strength tests. It should also be observed that, while the displacement of the dry specimens reached steady state w...

Polymer and fiber-reinforced polymer (FRP) composites have been adopted in a variety of engineering structures, ranging from aircraft and spacecraft, naval vessels, civil infrastructure, (see for examples reviews of Katnam et al.1, Hollaway2, Mouritz et al.3), cars and trains, wind turbine blades, to prosthetics and biomaterials for sutures and implants. These materials&#8217; durability is affected by complex service scenarios, which may include a combination of a) thermo-mechanical loading, e.g., freeze-thaw cycles in civil infrastructure4, subsonic/supersonic flight profiles5, wear in metal-backed polyethylene6); b) degradation due to environmental and chemical agents, e.g., sea water, de-icing, hydraulic fluid for aerospace and naval structures7-10, degradation of polymethylmethacrylate dental composites due to saliva11; c) complex interactions of materials in fastened or bonded joints, e.g., galvanic corrosion and debonding between dissimilar materials, whether in a carbon/fiber patch repair on an aircraft aluminum skin, or a carbon/PEEK bone plate fastened by stainless steel12.
There is unfortunately limited knowledge of the impact of concurrent in-service stimuli on the long-term durability of these materials. Most polymers may be categorized as viscoelastic materials. Mechanical loadings and environmental conditions significantly influence the viscoelastic response of polymers. Hence, reliable models for these materials&#8217; long-term behavior should be able to incorporate time-dependent responses to coupled hygrothermal, mechanical, chemical stimuli. This in turn will improve design predictions, safety and condition-based maintenance/replacement protocols.
There is a large literature body on experimental testing on hygrothermal effects, for example hygrothermal diffusion tests: if the scale of the samples allows it, the material samples may be positioned in a chamber at desired humidity and temperature levels. The samples are removed periodically to measure their mass and/or volume changes for a given amount of time, from weeks to years10,13-17. The hygrothermal test may be followed by mechanical testing, i.e., residual static/fatigue strength/fracture mechanics testing17-19, which only gives information on the effect of hygrothermal stimulus on the mechanical responses of materials. Test data may be fitted to diffusion models of varying complexity, from simple Fickian diffusion to models that include dependency on concentration, stress, temperature, reversible physical aging/plasticization and irreversible chemical reactions. This experimental output may be further incorporated in structural analyses.
Few authors have addressed the impact of simultaneous hygrothermal and mechanical stimuli. Among those researching FRP composites, Neumann and Garom20 immersed stressed and unstressed specimens in distilled water. Stress was applied by positioning the specimens inside compressed stainless steel springs, tuning the load by using different spring stiffnesses and compressive loads. A similar procedure is reported by Wan et al.21. Helbling and Karbhari22 employed a bending fixture inside an environmental chamber for different relative humidity percentages (RH%) and temperature levels. The pre-conditioned specimens were subjected to a given bending strain level, corresponding to a percentage of the static ultimate tensile strain for that composite. Kasturiarachchi and Pritchard23 prepared a stainless steel 4-point bending jig (one per specimen) that was positioned on a shelf in a large glass desiccator. The desiccator was partially filled with distilled water, had small leaks to prevent the buildup of pressure, and was placed in a humidity chamber at 95% RH. Gellert and Turley7 investigated marine-grade FRP composite specimens for their durability under combined creep loading and 100% RH. Their samples were loaded in 4-point bending at a constant load equal to 20% of the failure static flexure load, while fully immersed in sea water. The creep deflection was acquired periodically by using a thickness gauge between the outer surface of the beam in the central cross-section, and a glass plate (it is inferred that such measurement was performed outside the chamber). Abdel-Magid et al.24 placed samples of glass/epoxy in an Invar environmental fixture which was provided by NASA Langley, as the specimens were loaded in tension along the fiber direction, at 20% of the ultimate axial load. Ellyin and Rohrbarcher25 ran hygrothermal tests for up to 140 days, and then tested the specimens in fatigue on a hydraulic testing machine. The specimens were wrapped in a wet cheese cloth connected to a tube and a water supply. Earl et al.26 positioned their loading fixture and the specimens in a large environmental chamber (5.5 m3).
As discussed in many experimental studies, the environmental conditions affect the polymers&#8217; mechanical properties and responses. Some limited experiments also show that the existence of mechanical stress/strain influences the diffusion process in the polymers. Hence, to enhance understanding on the overall performance of polymer-based materials under both mechanical and non-mechanical effects, there is a need for concurrent testing.
There were several objectives behind the design of the testing platform discussed in this paper. First, the platform is part of the experimental setup in a multi-year investigation on the hygrothermo-mechanical behavior of different types of FRP sandwich composites for wind turbine and naval engineering applications. The test data are used to calibrate the parameters in the viscoelastic constitutive equations for the polymeric composites. The constitutive models are based on the work developed over the years by Muliana and collaborators27-30. The second objective was to have a low-cost and user-friendly testing platform, for example one that could be easily relocated in a laboratory (e.g., to a scale for mass measurements, or to the source of the fluid, e.g., one coming from a faucet, a fumehood or a flammable cabinet). The third goal was to create a testing platform that is resistant to a number of chemicals commonly used in service (particularly hydraulic fluid, de-icing, cleaning solvents for aerospace applications8-10), thus specimens could be immersed in such chemicals, and their durability could be assessed.
The chamber (Figure 1) was constructed with high-density polyethylene, which has high chemical resistance. As mentioned above, it is expected that future work will include hygrothermo-mechanical investigation of composites immersed in hydraulic fluid, de-icing, cleaning solvents. Since thermal regulation is an integral aspect of testing, expanded polystyrene foam was fit around the sides of the tank and secured in place by tape and the steel frame itself, to prevent heat exchange with the environment.
The lid of the chamber (Figure 2) was manufactured from transparent, 9.525 mm-thick polycarbonate, allowing the users to observe the specimens during testing without disturbing the test. The lid is secured in place by aluminum T-bars, which were machined to slide under overhanging brackets on the sides of the tank.
Bending in the specimens is enacted by three aluminum blocks, which hang down from the lid, and are fastened through slots in the lid. The three blocks allow up to four specimens to be tested at one time, while the lid slots allow the block spacing to be adjusted depending on the length of the specimens. Each block is rounded at the contact edge to a 12.7 mm diameter, in adherence to ASTM standard D790-10. The specimens are positioned beneath two of the three blocks, with an upward force applied at its center to induce bending (Figures 1-2).
The apparatus was designed with maximum versatility and ease-of-use in mind. Casters with 41.275 mm diameter are fastened beneath the chamber for mobility purposes. Above them, the tank is supported by a welded steel frame with a wire mesh bottom and cross beams for support. Angle stock spacers for the outside tank corners were manufactured to keep the insulation from being crushed by the overhead weight and displacement gauges (string pot apparatus, discussed later). Around the top, angle stock was used again for framing. Pulley and string potentiometer systems to measure mid-span deflection are mounted on four steel, square-tubing arches (Figure 3). The center two arches out of these four carry the string potentiometers and are adjustable to account for specimen versatility. The string potentiometers were constructed using a torsional spring (as can be found in retractable key lanyards) and potentiometers with three-pronged electronic outputs. The pulleys are aligned and mounted for use with a steel cable running from a rigid connection by the specimen to a hanging rod over the side of the chamber for adjustable weight application.
The load is applied to the specimen using a series of cables, pulleys, linkages and bolts. First, the specimen is placed into the U-bolt so that the 10 mm cross bar is contacting the middle of the span. A 9.525 mm diameter steel rod with eye bolts at each end is then connected to the U-bolt. This steel connection passes through the lid of the chamber. A steel cable and Kevlar thread are attached to the eyebolt opposite the U-bolt. This allows the Kevlar thread from the string potentiometer to read data from a rigid point. The steel cable continues upwards and passes over two pulleys that allow the load to be applied at the periphery of the tank. The cable is then attached to a 9.525 mm diameter steel rod that serves as a slotted weight hanger. This hanger provides a place where the slotted weights can be set in order to apply the desired load.

<table><tbody><tr><td>Aluminum 6061 rectangular bars</td><td>McMaster-Carr, USA</td><td>8975K268, 1668T72, 7062T17,&amp;nbsp;</td><td>Part of testing platform</td></tr><tr><td>Aluminum 6061 90&amp;deg; angles</td><td>McMaster-Carr, USA</td><td>8982K91, 8982K14&amp;nbsp;</td><td>Part of testing platform</td></tr><tr><td>440C stainless steel</td><td>McMaster-Carr, USA</td><td>6253K52</td><td>Part of testing platform</td></tr><tr><td>High-density polyethylene sheets</td><td>Tap Plastics, USA</td><td>N/A (0.236 in. thick x 10.75 in. wide x 16.75 in. long)</td><td>Part of testing platform</td></tr><tr><td>High-density polyethylene sheets</td><td>Tap Plastics, USA</td><td>N/A (0.354 in. thick x 6 in. wide x 10 in. long)</td><td>Part of testing platform</td></tr><tr><td>High-density polyethylene sheets</td><td>Tap Plastics, USA</td><td>N/A (0.354 in. thick x 6 in. wide x 16.75 in. long)</td><td>Part of testing platform</td></tr><tr><td>Polycarbonate sheets</td><td>Tap Plastics, USA</td><td>N/A (0.375 in thick, 11.5 in. wide, 17.5 in long)</td><td>Part of testing platform</td></tr><tr><td>Expanded polystyrene foam</td><td>Home Depot</td><td>Model # 310880 Internet # 202532855</td><td>Part of testing platform</td></tr><tr><td>Galvanized steel rope</td><td>McMaster-Carr, USA</td><td>3498T63</td><td>Part of testing platform</td></tr><tr><td>Steel eye bolt</td><td>McMaster-Carr, USA</td><td>3013T341</td><td>Part of testing platform</td></tr><tr><td>Low-carbon steel 90&amp;deg; angle</td><td>McMaster-Carr, USA</td><td>9017K444&amp;nbsp;</td><td>Part of testing platform</td></tr><tr><td>Low-carbon steel rods</td><td>McMaster-Carr, USA</td><td>8920K84, 8920K75, 8920K231, 8920K135, 8920K84&amp;nbsp;&amp;nbsp;&amp;nbsp;</td><td>Part of testing platform</td></tr><tr><td>Low-carbon steel tubes</td><td>McMaster-Carr, USA</td><td>6527K314, 8910K394, 8910K395, 8920K94&amp;nbsp;&amp;nbsp;</td><td>Part of testing platform</td></tr><tr><td>304 stainless steel U-bolt</td><td>McMaster-Carr, USA</td><td>8896T104</td><td>Part of testing platform</td></tr><tr><td>Steel pulley</td><td>McMaster-Carr, USA</td><td>3099T34</td><td>Part of testing platform</td></tr><tr><td>1008 carbon steel sheets</td><td>McMaster-Carr, USA</td><td>9302T113</td><td>Part of testing platform</td></tr><tr><td>Light duty swivel casters</td><td>Harbor Freight, USA</td><td>41519</td><td>Part of testing platform</td></tr><tr><td>100-lbf Vinyl Weight Set</td><td>Overstock.com</td><td>11767059</td><td>Part of testing platform</td></tr><tr><td>Closed-cell polyurethane foam</td><td>General Plastics, USA</td><td>FR-3704</td><td>Testing samples</td></tr><tr><td>Deionized water</td><td>Faucet, PurLab filtering system</td><td>N/A</td><td>Conditioning fluid of tank</td></tr><tr><td>Torsional spring</td><td>Retractable Key Clip, Ebay, USA</td><td>Lot 10</td><td>Used to build string potentiometer</td></tr><tr><td>Kevlar thread</td><td>Cabela&amp;rsquo;s</td><td>IK-321909</td><td>Used to build string potentiometer</td></tr><tr><td>10 kOhm potentiometer</td><td>Ebay, USA</td><td>3590S-2-103L</td><td>Used to build string potentiometer</td></tr><tr><td>Digital multimeter</td><td>Harbor Freight, USA</td><td>98674</td><td>Used to take resistance measurements of string potentiometer</td></tr></tbody></table>

a testing platform for durability studies of polymers and fiber-reinforced polymer composites under concurrent hygrothermo-mechanical stimuli

The durability of polymers and fiber-reinforced polymer composites under service condition is a critical aspect to be addressed for their robust designs and condition-based maintenance. These materials are adopted in a wide range of engineering applications, from aircraft and ship structures, to bridges, wind turbine blades, biomaterials and biomedical implants. Polymers are viscoelastic materials, and their response may be highly nonlinear and thus make it challenging to predict and monitor their in-service performance. The laboratory-scale testing platform presented herein assists the investigation of the influence of concurrent mechanical loadings and environmental conditions on these materials. The platform was designed to be low-cost and user-friendly. Its chemically resistant materials make the platform adaptable to studies of chemical degradation due to in-service exposure to fluids. An example of experiment was conducted at RT on closed-cell polyurethane foam samples loaded with a weight corresponding to ~50% of their ultimate static and dry load. Results show that the testing apparatus is appropriate for these studies. Results also highlight the larger vulnerability of the polymer under concurrent loading, based on the higher mid-point displacements and lower residual failure loads. Recommendations are made for additional improvements to the testing apparatus.

The testing apparatus has successfully held specimens immersed in a fluid under three-point bending. With reasonable precisions, specimens can be loaded and tested with accurate readouts from the potentiometers for mid-point deflection changes. The change in electrical resistance can be recorded to 4 significant figures, resulting in a displacement resolution of the order of 0.1 &#181;m.
Hygrothermo-mechanical tests were conducted at RT on two groups of four specimens of closed-cell polyuretha...

Watch this Scientific Journal Video about A Testing Platform for Durability Studies of Polymers and Fiber-reinforced Polymer Composites under Concurrent Hygrothermo-mechanical Stimuli at JoVE.com

A Testing Platform for Durability Studies of Polymers and Fiber-reinforced Polymer Composites under Concurrent Hygrothermo-mechanical Stimuli

The durability of polymers and fiber-reinforced polymer composites in service is a critical aspect for their designs and condition-based maintenance. We present a novel low-cost laboratory testing platform for the investigation of the influence of concurrent mechanical and environmental loadings, and may help design more efficient yet safer composite structures.

The durability of polymers and fiber-reinforced polymer composites under service condition is a critical aspect to be addressed for their robust designs ...

a-testing-platform-for-durability-studies-polymers-fiber-reinforced

Universidad de Cartagena UDEC

Research

Education

JoVE Journal

JoVE Core

Civil Engineering

Mechanical Engineering

Engineering

Unit 1

Elasticity, Creep, and Shrinkage in Concrete

Internal Forces

SCIENTISTS IN ACTION

13.7K Views.  University of California, Davis. The durability of polymers and fiber-reinforced polymer composites in service is a critical aspect for their designs and condition-based maintenance. We present a novel low-cost laboratory testing platform for the investigation of the influence of concurrent mechanical and environmental loadings, and may help design more efficient yet safer composite structures.

Video: A Testing Platform for Durability Studies of Polymers and Fiber-reinforced Polymer Composites under Concurrent Hygrothermo-mechanical Stimuli

Synthesis of Programmable Main-chain Liquid-crystalline Elastomers Using a Two-stage Thiol-acrylate Reaction

This study presents a novel two-stage thiol-acrylate Michael addition-photopolymerization (TAMAP) reaction to prepare main-chain liquid-crystalline elastomers (LCEs) with facile control over network structure and programming of an aligned monodomain. Tailored LCE networks were synthesized using routine mixing of commercially available starting materials and pouring monomer solutions into molds to cure. An initial polydomain LCE network is formed via a self-limiting thiol-acrylate Michael-addition reaction. Strain-to-failure and glass transition behavior were investigated as a function of crosslinking monomer, pentaerythritol tetrakis(3-mercaptopropionate) (PETMP). An example non-stoichiometric system of 15 mol% PETMP thiol groups and an excess of 15 mol% acrylate groups was used to demonstrate the robust nature of the material. The LCE formed an aligned and transparent monodomain when stretched, with a maximum failure strain over 600%. Stretched LCE samples were able to demonstrate both stress-driven thermal actuation when held under a constant bias stress or the shape-memory effect when stretched and unloaded. A permanently programmed monodomain was achieved via a second-stage photopolymerization reaction of the excess acrylate groups when the sample was in the stretched state. LCE samples were photo-cured and programmed at 100%, 200%, 300%, and 400% strain, with all samples demonstrating over 90% shape fixity when unloaded. The magnitude of total stress-free actuation increased from 35% to 115% with increased programming strain. Overall, the two-stage TAMAP methodology is presented as a powerful tool to prepare main-chain LCE systems and explore structure-property-performance relationships in these fascinating stimuli-sensitive materials.

A novel methodology is presented to synthesize and program main-chain liquid-crystalline elastomers using commercially available starting monomers. A wide range of thermomechanical properties was tailored by adjusting the amount of crosslinker, while the actuation performance was dependent on the amount of applied strain during programming.

This study presents a novel two-stage thiol-acrylate Michael addition-photopolymerization (TAMAP) reaction to prepare main-chain liquid-crystalline ...

Chemistry

Environmentally-controlled Microtensile Testing of Mechanically-adaptive Polymer Nanocomposites for ex vivo Characterization

Implantable microdevices are gaining significant attention for several biomedical applications1-4. Such devices have been made from a range of materials, each offering its own advantages and shortcomings5,6. Most prominently, due to the microscale device dimensions, a high modulus is required to facilitate implantation into living tissue. Conversely, the stiffness of the device should match the surrounding tissue to minimize induced local strain7-9. Therefore, we recently developed a new class of bio-inspired materials to meet these requirements by responding to environmental stimuli with a change in mechanical properties10-14. Specifically, our poly(vinyl acetate)-based nanocomposite (PVAc-NC) displays a reduction in stiffness when exposed to water and elevated temperatures (e.g. body temperature). Unfortunately, few methods exist to quantify the stiffness of materials in vivo15, and mechanical testing outside of the physiological environment often requires large samples inappropriate for implantation. Further, stimuli-responsive materials may quickly recover their initial stiffness after explantation. Therefore, we have developed a method by which the mechanical properties of implanted microsamples can be measured ex vivo, with simulated physiological conditions maintained using moisture and temperature control13,16,17. 
To this end, a custom microtensile tester was designed to accommodate microscale samples13,17 with widely-varying Young's moduli (range of 10 MPa to 5 GPa). As our interests are in the application of PVAc-NC as a biologically-adaptable neural probe substrate, a tool capable of mechanical characterization of samples at the microscale was necessary. This tool was adapted to provide humidity and temperature control, which minimized sample drying and cooling17. As a result, the mechanical characteristics of the explanted sample closely reflect those of the sample just prior to explantation.
The overall goal of this method is to quantitatively assess the in vivo mechanical properties, specifically the Young's modulus, of stimuli-responsive, mechanically-adaptive polymer-based materials. This is accomplished by first establishing the environmental conditions that will minimize a change in sample mechanical properties after explantation without contributing to a reduction in stiffness independent of that resulting from implantation. Samples are then prepared for implantation, handling, and testing (Figure 1A). Each sample is implanted into the cerebral cortex of rats, which is represented here as an explanted rat brain, for a specified duration (Figure 1B). At this point, the sample is explanted and immediately loaded into the microtensile tester, and then subjected to tensile testing (Figure 1C). Subsequent data analysis provides insight into the mechanical behavior of these innovative materials in the environment of the cerebral cortex.

Environmentally-controlled Microtensile Testing of Mechanically-adaptive Polymer Nanocomposites for ex vivo Characterization

A method is discussed by which the in vivo mechanical behavior of stimuli-responsive materials is monitored as a function of time. Samples are tested ex vivo using a microtensile tester with environmental controls to simulate the physiological environment. This work further promotes understanding the in vivo behavior of our material.

Implantable microdevices are gaining significant attention for several biomedical applications1-4. Such devices have been made from a range of materials, ...

Bioengineering

In Situ High Pressure Hydrogen Tribological Testing of Common Polymer Materials Used in the Hydrogen Delivery Infrastructure

High pressure hydrogen gas is known to adversely affect metallic components of compressors, valves, hoses, and actuators. However, relatively little is known about the effects of high pressure hydrogen on the polymer sealing and barrier materials also found within these components. More study is required in order to determine the compatibility of common polymer materials found in the components of the hydrogen fuel delivery infrastructure with high pressure hydrogen. As a result, it is important to consider the changes in physical properties such as friction and wear in situ while the polymer is exposed to high pressure hydrogen. In this protocol, we present a method for testing the friction and wear properties of ethylene propylene diene monomer (EPDM) elastomer samples in a 28 MPa high pressure hydrogen environment using a custom-built in situ pin-on-flat linear reciprocating tribometer. Representative results from this testing are presented which indicate that the coefficient of friction between the EPDM sample coupon and steel counter surface is increased in high pressure hydrogen as compared to the coefficient of friction similarly measured in ambient air.

In Situ High Pressure Hydrogen Tribological Testing of Common Polymer Materials Used in the Hydrogen Delivery Infrastructure

A test methodology for quantifying tribological properties of polymers used in hydrogen infrastructure service is demonstrated and characteristic results for a common elastomer are discussed.

High pressure hydrogen gas is known to adversely affect metallic components of compressors, valves, hoses, and actuators. However, relatively little is ...

The Effect of Construction and Demolition Waste Plastic Fractions on Wood-Polymer Composite Properties

Construction and demolition waste (CDW), including valuable materials such as plastics, have a remarkable influence on the waste sector. In order for plastic materials to be re-utilized, they must be identified and separated according to their polymer composition. In this study, the identification of these materials was performed using near-infrared spectroscopy (NIR), which identified material based on their physical-chemical properties. Advantages of the NIR method are a low environmental impact and rapid measurement (within a few seconds) in the spectral range of 1600-2400 nm without special sample preparation. Limitations include its inability to analyze dark materials. The identified polymers were utilized as a component for wood-polymer composite (WPC) that consists of a polymer matrix, low cost fillers, and additives. The components were first compounded with an agglomeration apparatus, followed by production by extrusion. In the agglomeration process, the aim was to compound all materials to produce uniformly distributed and granulated materials as pellets. During the agglomeration process, the polymer (matrix) was melted and fillers and other additives were then mixed into the melted polymer, being ready for the extrusion process. In the extrusion method, heat and shear forces were applied to a material within the barrel of a conical counter-rotating twin-screw type extruder, which reduces the risk of burning the materials and lower shear mixing. The heated and sheared mixture was then conveyed through a die to give the product the desired shape. The above-described protocol proved the potential for re-utilization of CDW materials. Functional properties must be verified according to the standardized tests, such as flexural, tensile, and impact strength tests for the material.

Secondary material streams have been shown to include potential raw materials for production. Presented here is a protocol in which CDW-plastic waste as a raw material is identified, followed by various processing steps (agglomeration, extrusion). As a result, a composite material was produced, and mechanical properties were analyzed.

Construction and demolition waste (CDW), including valuable materials such as plastics, have a remarkable influence on the waste sector. In order for ...

Environment

Ultrasonic Fatigue Testing in the Tension-Compression Mode

Ultrasonic fatigue testing is one of a few methods which allow investigating fatigue properties in the ultra-high cycle region. The method is based on exposing the specimen to longitudinal vibrations on its resonance frequency close to 20 kHz. With use of this method, it is possible to significantly decrease the time required for the test, when compared to conventional testing devices usually working at frequencies under 200 Hz. It is also used to simulate loading of material during operation in high speed conditions, such as those experienced by components of jet engines or car turbo pumps. It is necessary to operate only in the high and ultra-high cycle region, due to the possibility of extremely high deformation rates, which can have a significant influence on the test results. Specimen shape and dimensions have to be carefully selected and calculated to fulfill the resonance condition of the ultrasonic system; thus, it is not possible to test the full components or specimens of arbitrary shape. Before each test, it is necessary to harmonize the specimen with the frequency of the ultrasonic system to compensate for deviations of the real shape from the ideal one. It is not possible to run a test until a total fracture of the specimen, since the test is automatically terminated after initiation and propagation of the crack to a certain length, when the stiffness of the system changes enough to shift the system out of the resonance frequency. This manuscript describes the process of evaluation of materials' fatigue properties at high-frequency ultrasonic fatigue loading with use of mechanical resonance at a frequency close to 20 kHz. The protocol includes a detailed description of all steps required for a correct test, including specimen design, stress calculation, harmonizing with the resonance frequency, performing the test, and final static fracture.

A protocol for ultrasonic fatigue testing in the high and ultra-high cycle region in axial tension-compression loading mode.

Ultrasonic fatigue testing is one of a few methods which allow investigating fatigue properties in the ultra-high cycle region. The method is based on ...

Disentangling High Strength Copolymer Aramid Fibers to Enable the Determination of Their Mechanical Properties

Traditionally, soft body armor has been made from poly(p-phenylene terephthalamide) (PPTA) and ultra-high molecular weight polyethylene. However, to diversify the fiber choices in the United States body armor market, copolymer fibers based on the combination of 5-amino-2-(p-aminophenyl) benzimidazole (PBIA) and the more conventional PPTA were introduced. Little is known regarding the long-term stability of these fibers, but as condensation polymers, they are expected to have potential sensitivity to moisture and humidity. Therefore, characterizing the strength of the materials and understanding their vulnerability to environmental conditions is important for evaluating their use lifetime in safety applications. Ballistic resistance and other critical structural properties of these fibers are predicated on their strength. To accurately determine the strength of the individual fibers, it is necessary to disentangle them from the yarn without introducing any damage. Three aramid-based copolymer fibers were selected for the study. The fibers were washed with acetone followed by methanol to remove an organic coating that held the individual fibers in each yarn bundle together. This coating makes it difficult to separate single fibers from the yarn bundle for mechanical testing without damaging the fibers and affecting their strength. After washing, fourier transform infrared (FTIR) spectroscopy was performed on both washed and unwashed samples and the results were compared. This experiment has shown that there are no significant variations in the spectra of poly(p-phenylene-benzimidazole-terephthalamide-co-p-phenylene terephthalamide) (PBIA-co-PPTA1) and PBIA-co-PPTA3 after washing, and only a small variation in intensity for PBIA. This indicates that the acetone and methanol rinses are not adversely affecting the fibers and causing chemical degradation. Additionally, single fiber tensile testing was performed on the washed fibers to characterize their initial tensile strength and strain to failure, and compare those to other reported values. Iterative procedural development was necessary to find a successful method for performing tensile testing on these fibers.

The primary goal of the study is to develop a protocol to prepare consistent specimens for accurate mechanical testing of high strength copolymer aramid fibers, by removing a coating and disentangling the individual fiber strands without introducing significant chemical or physical degradation.

Traditionally, soft body armor has been made from poly(p-phenylene terephthalamide) (PPTA) and ultra-high molecular weight polyethylene. However, to ...

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates

Many body armor designs incorporate unidirectional (UD) laminates. UD laminates are constructed of thin (&#60;0.05 mm) layers of high-performance yarns, where the yarns in each layer are oriented parallel to each other and held in place using binder resins and thin polymer films. The armor is constructed by stacking the unidirectional layers in different orientations. To date, only very preliminary work has been performed to characterize the ageing of the binder resins used in unidirectional laminates and the effects on their performance. For example, during the development of the conditioning protocol used in the National Institute of Justice Standard-0101.06, UD laminates showed visual signs of delamination and reductions in V50, which is the velocity at which half of the projectiles are expected to perforate the armor, after ageing. A better understanding of the material property changes in UD laminates is necessary to comprehend the long-term performance of armors constructed from these materials. There are no current standards recommended for mechanically interrogating unidirectional (UD) laminate materials. This study explores methods and best practices for accurately testing the mechanical properties of these materials and proposes a new test methodology for these materials. Best practices for ageing these materials are also described.

The goal of the study was to develop protocols to prepare consistent specimens for accurate mechanical testing of high-strength aramid or ultra-high-molar-mass polyethylene-based flexible unidirectional composite laminate materials and to describe protocols for performing artificial ageing on these materials.

Many body armor designs incorporate unidirectional (UD) laminates. UD laminates are constructed of thin (&#60;0.05 mm) layers of high-performance yarns, ...

Artificial Thermal Ageing of Polyester Reinforced and Polyvinyl Chloride Coated Technical Fabric

Architectural fabric AF9032 has been subjected to artificial thermal ageing to determine changes of the material parameters of the fabric. The proposed method is based on the accelerated ageing approach proposed by Arrhenius. 300 mm x 50 mm samples were cut in the warp and fill directions and placed in a thermal chamber at 80 &#176;C for up to 12 weeks or at 90 &#176;C for up to 6 weeks. Then after one week of conditioning at ambient temperature, the samples were uniaxially tensioned at a constant strain rate. Experimentally, the parameters were determined for the non-linear elastic (linear piecewise) and viscoplastic (Bodner&#8211;Partom) models. Changes in these parameters were studied with respect to the ageing temperature and ageing period. In both cases, the linear approximation function was successfully applied using the simplified methodology of Arrhenius. A correlation was obtained for the fill direction between experimental results and the results from the Arrhenius approach. For the warp direction, the extrapolation results exhibited some differences. Increasing and decreasing tendencies have been observed at both temperatures. The Arrhenius law was confirmed by the experimental results only for the fill direction. The proposed method makes it possible to predict real fabric behavior during long term exploitation, which is a critical issue in the design process.

Here, we simulate accelerated thermal ageing of technical fabric and see how this ageing process influences the mechanical properties of the fabric.

Architectural fabric AF9032 has been subjected to artificial thermal ageing to determine changes of the material parameters of the fabric. The proposed ...

Fabrication and Mechanical Property Assessment of Fiber Composite Laminates

Measuring the Mechanical Properties of Glass Fiber Reinforcement Polymer Composite Laminates Obtained by Different Fabrication Processes

The traditional wet hand lay-up process (WL) has been widely applied in the manufacturing of fiber composite laminates. However, due insufficiency in the forming pressure, the mass fraction of fiber is reduced and lots of air bubbles are trapped inside, resulting in low-quality laminates (low stiffness and strength). The wet hand lay-up/vacuum bag (WLVB) process for the fabrication of composite laminates is based on the traditional wet hand lay-up process, using a vacuum bag to remove air bubbles and provide pressure, and then carrying out the heating and curing process. 
Compared with the traditional hand lay-up process, laminates manufactured by the WLVB process show superior mechanical properties, including better strength and stiffness, higher fiber volume fraction, and lower void volume fraction, which are all benefits for composite laminates. This process is completely manual, and it is greatly influenced by the skills of the preparation personnel. Therefore, the products are prone to defects such as voids and uneven thickness, leading to unstable qualities and mechanical properties of the laminate. Hence, it is necessary to finely describe the WLVB process, finely control steps, and quantify material ratios, in order to ensure the mechanical properties of laminates. 
This paper describes the meticulous process of the WLVB process for preparing woven plain patterned glass fiber reinforcement composite laminates (GFRPs). The fiber volume content of laminates was calculated using the formula method, and the calculated results showed that the fiber volume content of WL laminates was 42.04%, while that of WLVB laminates was 57.82%, increasing by 15.78%. The mechanical properties of the laminates were characterized using tensile and impact tests. The experimental results revealed that with the WLVB process, the strength and modulus of the laminates were enhanced by 17.4% and 16.35%, respectively, and the specific absorbed energy was increased by 19.48%.

Author Spotlight: Enhancing Fiber Composite Laminate Quality with the Wet Hand Lay-Up/Vacuum Bag Process 

This paper describes a fabrication process for fiber-reinforced polymer matrix composite laminates obtained using the wet hand lay-up/vacuum bag method.

The traditional wet hand lay-up process (WL) has been widely applied in the manufacturing of fiber composite laminates. However, due insufficiency in the ...

Tension Tests of Polymers

Source:&#160;Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
Polymeric materials are widely used in civil structures, with uses ranging from very soft sealants to more rigid pipes in water and wastewater systems. The most basic definition of a polymer is a molecular structure with repeating subunits. The term polymer comes from Greek, where &#34;poly&#34; means many, and &#34;-mer&#34; means basic unit. Monomers, or single mers, are the specific repeating units. With polymers, the structure, including the length of the carbon backbone and the varying flexibility, will dictate the properties of the polymer. Polymers are classified into 3 subcategories: plastics, elastomers, and rigid rod polymers. Plastics are further subdivided into thermosets, which do not soften on heating, and thermoplastics, which do soften when heated and harden on cooling. Additionally, thermoplastics are mostly linear or branched polymers with little to no cross-linking, whereas thermosets exhibit 3D structure and have extensive cross-linking. Elastomers, or rubbers, are long, coiled chains and can be stretched to twice the original length, but will contract back to the original size when released, whereas rigid rod polymers do not stretch and are strong, crystalline structures.
In this laboratory, we will look at several different polymeric materials, including high density polyethylene (HDPE), polyvinyl chlorides (PVC), nylon, and methyl methacrylate (acrylic) in order to understand the breadth and diversity of the stress-strain curves for these materials and how their mechanical properties affect their performance.

Uniaxial Tensile Test Strength for Polymers

Source:&#160;Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
Polymeric materials are widely used in civil ...

A Testing Platform for Durability Studies of Polymers and Fiber-reinforced Polymer Composites under Concurrent Hygrothermo-mechanical Stimuli

Summary

Explore More Videos

Chapters in this video

Synthesis of Programmable Main-chain Liquid-crystalline Elastomers Using a Two-stage Thiol-acrylate Reaction

Environmentally-controlled Microtensile Testing of Mechanically-adaptive Polymer Nanocomposites for ex vivo Characterization

In Situ High Pressure Hydrogen Tribological Testing of Common Polymer Materials Used in the Hydrogen Delivery Infrastructure

The Effect of Construction and Demolition Waste Plastic Fractions on Wood-Polymer Composite Properties

Ultrasonic Fatigue Testing in the Tension-Compression Mode

Disentangling High Strength Copolymer Aramid Fibers to Enable the Determination of Their Mechanical Properties

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates

Artificial Thermal Ageing of Polyester Reinforced and Polyvinyl Chloride Coated Technical Fabric

Measuring the Mechanical Properties of Glass Fiber Reinforcement Polymer Composite Laminates Obtained by Different Fabrication Processes

Tension Tests of Polymers