我们感谢布拉施克，格伦​​沃尔德和WITTWER实验室的咨询和技术援助的成员。这项工作是由PCMC基金会，美国国立卫生研究院R01 MH092256和DP2 MH100008和优生优育基金会的研究经费＃1-FY13-425的3月，为广东健力宝的支持。

1。 DNA的制备<ol><li>制备的DNA的裂解缓冲液:50mM的KCl，10mM的Tris-盐酸的pH 8.3，0.3％吐温20，0.3％NP40。加入新鲜的蛋白酶K至对使用12的天1毫克/毫升的最终浓度。 </li><li>组织收集: <ol><li>对于成年鱼翅夹: <ol><li>麻醉鱼:将鱼在0.004％的MS-222（三卡因）解决方案。等到鳃运动减慢。 </li><li>把鱼放在一摞5-10的Kimwipes切一小片尾翼，约2-3毫米，用无菌刀片的。 </li><li>迅速将鱼与淡水回收标记罐;仔细标注两个油箱和相应的管道将包含翅夹。换水及隔日喂鱼。 </li><li>拿起翅片夹，用无菌移液管尖端，并将其转移到充满100μl的DNA的裂解缓冲液的管中。 </li><li>丢弃枪头，并丢弃刀片成锐器容器。 </li></ol></li><li>胚胎长尾夹: <ol><li>把胚胎成0.004％的MS-222（三卡因）溶液。等待2分钟。 </li><li>切下一块尾部用解剖显微镜下用镊子。 </li><li>把尾巴放入盛有30微升的DNA裂解液标记管。 </li><li>赶紧把胚胎成含100微升4％多聚甲醛管。 </li><li>标签管与胚胎和相应的尾管中。 </li><li>存储与胚胎试管在4℃过夜固定。 </li><li>使用，以减少污染的每个胚胎之间的Milli-Q水和清洁的Kimwipes的钳子。 </li></ol></li><li>对于整个胚胎: <ol><li>把胚胎成0.004％的MS-222（三卡因）溶液。等待2分钟。 </li><li>放1-5胚胎在充满100微升DNA的裂解缓冲液的管中。 Dechorionation是没有必要的。 </li></ol></li></ol></li><li> DNA酶切 孵育组织（鳍或尾巴夹或胚胎）试管在55℃下4小时到过夜12。 </li><li>灭活蛋白酶K 热管至95℃15分钟12。 DNA应立即用于PCR，或储存在-20℃下长达3个月。 </li></ol> 2。 PCR <ol><li>手动或通过引物设计软件（ 如 Lightscanner引物设计软件-Biofire）设计引物。 PCR产物为HRMA通常50-200个基点; PCR产物进行SNP检测应该是较小的，通常50-80个基点。 </li><li> PCR <ol><li>进行PCR反应在96孔或384孔板。 </li><li>使用10μl的总体积:4微升LightScanner母液（0.1ü热启动Taq-AB聚合酶，缓冲液，0.2mM的dNTPs浓度，2mM的氯化镁，和1x荧光双链DNA结合染料）; 5pmol的各引物，从成年尾鳍或胚胎尾部13 3微升基因组DNA提取1微升基因组DNA模板。 </li><li>盖样品与30μl的矿物油。 </l我&gt; <li>用光学透明粘合剂密封覆盖板。 </li><li>优化的PCR循环条件，典型的条件是95℃5分钟，10秒30个循环的95℃，25秒，60℃，30秒，72℃，结束与95℃30秒，并冷却至15℃。 </li><li>商店PCR板在4℃或直接继续HRMA。 </li><li>通过在PCR过程中的初始优化利用琼脂糖凝胶电泳的大小的分析证实了我们的PCR产物，以及如果所述，通过PCR产物的测序。 </li></ol></li></ol> 3。 HRMA <ol><li>热板<ol><li>放置板在熔融分析系统。 </li><li>打开软件（LightScanner软件呼叫的IT 2.0）。 </li><li>从60-95℃，热板</li><li>创建一个新的数据存储文件。 </li></ol></li><li>分析HRMA数据（ 图2）。 分析的多个步骤是可能的。我们显示最常用的一组数据米anipulations。 <ol><li>子集设置 单击子集标签。选择井样品。 </li><li>正常化<ol><li>在左边的面板中选择标准化选项卡。消除荧光方差，手动定位平行双线路的预（初始）和后（最终）熔融区域如图所示（ 图2C，箭头）和归一化所有样品的预熔融后和熔融的荧光信号，以1和0 ，分别为14。 </li><li>调整线的定位，以使熔化区是在该区域的前，后熔线之间，但没有被选中。在一般情况下，下民，下最大（和上最小和上最大）温度线应放置约1°C分开。 </li><li>选择温度职位正常化，使得所有样品具有最大或满（100％）的荧光的预熔区和最小或无（0％）荧光为后熔融区域（尽量将POSsible）。正常化应该导致近水平线以1延​​伸，直到熔点，然后近水平线从在0的最小荧光熔融点的最大荧光;不应该有荧光水平高于1或0以下。例如，在图2C中 ，用79-80℃，温度范围内归一化的预熔化曲线</li></ol></li><li>分组/集群 区分基于其熔化温度（ 图2C，绿框）的基因型。选择分组 。 <ol><li>从下分组部分中的标准选择列表中选择Autogroup。 </li><li>选择正常或高的单转换或多个过渡分别从灵敏度选择列表下的分组部分熔解图谱。 </li><li>选择计算根据分组节组。 </li><li>转到文件菜单，然后单击保存以保存结果。 </li></ol></li></ol></li></ol>

<ol>
	<li>Kawakami, K., Takeda, H., Kawakami, N., Kobayashi, M., Matsuda, N., Mishina, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+transposon-mediated+gene+trap+approach+identifies+developmentally+regulated+genes+in+zebrafish.">A transposon-mediated gene trap approach identifies developmentally regulated genes in zebrafish.</a> Dev. Cell. 7 (1), 133-144 (2004).</li><li>Kwan, K. M., Fujimoto, E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+Tol2kit:+a+multisite+gateway-based+construction+kit+for+Tol2+transposon+transgenesis+constructs.">The Tol2kit: a multisite gateway-based construction kit for Tol2 transposon transgenesis constructs.</a> Dev. Dyn. 236 (11), 3088-3099 (2007).</li><li>Sander, J. D., Cade, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Targeted+gene+disruption+in+somatic+zebrafish+cells+using+engineered+TALENs.">Targeted gene disruption in somatic zebrafish cells using engineered TALENs.</a> Nat. Biotechnol. 29 (8), 697-698 (2011).</li><li>Huang, P., Xiao, A., Zhou, M., Zhu, Z., Lin, S., Zhang, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heritable+gene+targeting+in+zebrafish+using+customized+TALENs.">Heritable gene targeting in zebrafish using customized TALENs.</a> Nat. Biotechnol. 29 (8), 699-700 (2011).</li><li>Vossen, R. H. A. M., Aten, E., Roos, A., Den Dunnen, J. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-resolution+melting+analysis+(HRMA):+more+than+just+sequence+variant+screening.">High-resolution melting analysis (HRMA): more than just sequence variant screening.</a> Hum. Mutation. 30 (6), 860-866 (2009).</li><li>Dahlem, T. J., Hoshijima, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simple+methods+for+generating+and+detecting+locus-specific+mutations+induced+with+TALENs+in+the+zebrafish+genome.">Simple methods for generating and detecting locus-specific mutations induced with TALENs in the zebrafish genome.</a> PLoS Genet. 8 (8), (2012).</li><li>Liew, M., Pryor, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Genotyping+of+single-nucleotide+polymorphisms+by+high-resolution+melting+of+small+amplicons.">Genotyping of single-nucleotide polymorphisms by high-resolution melting of small amplicons.</a> Clin. Chem. 50 (7), 1156-1164 (2004).</li><li>Herrmann, M. G., Durtschi, J. D., Bromley, L. K., Wittwer, C. T., Voelkerding, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=V+Amplicon+DNA+melting+analysis+for+mutation+scanning+and+genotyping:+cross-platform+comparison+of+instruments+and+dyes.">V Amplicon DNA melting analysis for mutation scanning and genotyping: cross-platform comparison of instruments and dyes.</a> Clin. Chem. 52 (3), 494-503 (2006).</li><li>Carrillo, J., Mart&#237;nez, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High+resolution+melting+analysis+for+the+identification+of+novel+mutations+in+DKC1+and+TERT+genes+in+patients+with+dyskeratosis+congenita.">High resolution melting analysis for the identification of novel mutations in DKC1 and TERT genes in patients with dyskeratosis congenita.</a> Blood Cell. Mol. Dis.. 49 (3-4), 140-146 (2012).</li><li>Thomsen, N., Ali, R. G., Ahmed, J. N., Arkell, R. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High+resolution+melt+analysis+(HRMA);+a+viable+alternative+to+agarose+gel+electrophoresis+for+mouse+genotyping.">High resolution melt analysis (HRMA); a viable alternative to agarose gel electrophoresis for mouse genotyping.</a> PloS one. 7 (9), (2012).</li><li>Vorkas, P. A., Poumpouridou, N., Agelaki, S., Kroupis, C., Georgoulias, V., Lianidou, E. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=PIK3CA+hotspot+mutation+scanning+by+a+novel+and+highly+sensitive+high-resolution+small+amplicon+melting+analysis+method.">PIK3CA hotspot mutation scanning by a novel and highly sensitive high-resolution small amplicon melting analysis method.</a> J. Mol. Diagn. 12 (5), 697-704 (2010).</li><li>Parant, J. M., George, S. A., Pryor, R., Wittwer, C. T., Yost, H. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+rapid+and+efficient+method+of+genotyping+zebrafish+mutants.">A rapid and efficient method of genotyping zebrafish mutants.</a> Dev. Dyn. 238 (12), 3168-3174 (2009).</li><li>Xing, L., Hoshijima, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Zebrafish+foxP2+zinc+finger+nuclease+mutant+has+normal+axon+pathfinding.">Zebrafish foxP2 zinc finger nuclease mutant has normal axon pathfinding.</a> PloS one. 7 (8), (2012).</li><li>Raghavendra, A., Siji, A., Sridhar, T. S., Phadke, K., Vasudevan, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+High+Resolution+Melting+analysis+as+an+alternate+tool+to+screen+for+risk+alleles+associated+with+small+kidneys+in+Indian+newborns.">Evaluation of High Resolution Melting analysis as an alternate tool to screen for risk alleles associated with small kidneys in Indian newborns.</a> BMC Nephrol. 12 (1), 60 (2011).</li><li>Herrmann, M. G., Durtschi, J. D., Wittwer, C. T., Voelkerding, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=V+Expanded+instrument+comparison+of+amplicon+DNA+melting+analysis+for+mutation+scanning+and+genotyping.">V Expanded instrument comparison of amplicon DNA melting analysis for mutation scanning and genotyping.</a> Clin. Chem. 53 (8), 1544-1548 (2007).</li><li>Wittwer, C. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-Resolution+Genotyping+by+Amplicon+Melting+Analysis+Using+LCGreen.">High-Resolution Genotyping by Amplicon Melting Analysis Using LCGreen.</a> Clin. Chem. 49 (6), 853-860 (2003).</li><li>Dimitrakopoulos, L., Vorkas, P. A., Georgoulias, V., Lianidou, E. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+closed-tube+methylation-sensitive+high+resolution+melting+assay+(MS-HRMA)+for+the+semi-quantitative+determination+of+CST6+promoter+methylation+in+clinical+samples.">A closed-tube methylation-sensitive high resolution melting assay (MS-HRMA) for the semi-quantitative determination of CST6 promoter methylation in clinical samples.</a> BMC Cancer. 12, 486-48 (2012).</li><li>Jeng, K., Gaydos, C. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparative+analysis+of+two+broad-range+PCR+assays+for+pathogen+detection+in+positive-blood-culture+bottles:+PCR-high-resolution+melting+analysis+versus+PCR-mass+spectrometry.">Comparative analysis of two broad-range PCR assays for pathogen detection in positive-blood-culture bottles: PCR-high-resolution melting analysis versus PCR-mass spectrometry.</a> J. Clin. Microbiol. 50 (10), 3287-3292 (2012).</li></ol>

作者什么都没有透露。

PCR结合HRMA是一种功​​能强大的技术，斑马鱼基因分型。这种方法的优点是它的速度，鲁棒性，以及灵敏度来检测偶数的点突变。整个协议，从翅片夹熔化曲线分析，可在少于八小时由个人执行的。此外，该技术是适合于高通量筛选;不需要使用溴化乙锭;和密封所有PCR和分析步骤，这有助于减少污染的问题。 这种技术的一个关键步骤是PCR扩增子和引物设计。典型的长度为PCR?...

斑马鱼（ 斑马鱼 ）是脊椎动物模型系统广泛用于开发和疾病模型的研究。最近，众多的转基因和基因突变技术已经开发了斑马鱼。快速的转基因技术，通常根据一个TOL2座子系统1中，已合并为多个DNA片段组件2改进的克隆选择。锌指核酸酶（ZFN）和转录活化因子样效应物核酸酶（TALENS）已被用于靶向基因座在两个体细胞和生殖系细胞，斑马鱼3,4。这些技术可以有效地产生转基因动物，具有高频突变的创建和种系传递3,4。 尽管取得了这些进展，在传统的斑马鱼基因分型技术限制的诱变和转基因工具的全部功能。 PCR然后进行凝胶电泳，有时结合不受限制。Ñ​​酶消化，被广泛用于检测基因组的修饰，但很费时，并确定小插入或缺失不敏感。 TaqMan探针检测具有较高的初始成本，需要仔细优化。 PCR产物的测序可能需要几天时间，并且是不实用的大规模筛选。限制性片段长度多态性（RFLP）分析，只能判别影响的限制性内切酶识别位点的一个有限的范围内的SNP。 高分辨率熔解分析（HRMA），封闭管后的PCR分析方法，是一种最近开发的方法，该方法快速，灵敏，价格低廉，适合于筛选大量样品。 HRMA可用于检测单核苷酸多态性，突变，和转基因5-7。 HRMA是基于双链DNA热变性，并且每个PCR扩增子具有唯一的解离（熔体）特性5。样品可以分辨由于吨ø其不同的核苷酸组成，GC含量，或长度，通常在用荧光染料的组合，只有结合双链DNA 8。因此，HRMA可以基于不同的熔融曲线的特征区分不同基因型。因为HRMA使用廉价的试剂和是一个单步PCR后的过程中，它可用于高通量的策略。 HRMA是破坏性的，所以下面的分析将PCR扩增子可以用于其他应用。 HRMA已在许多生物和系统，包括细胞系，小鼠和人类9-11中得到应用。它的使用最近在斑马鱼被描述检测由锌指核酸酶（ZFN）和塔伦斯6,12,13突变。 在本文中，我们将描述如何在胚胎和成年斑马鱼进行基于PCR的HRMA（ 图1）。这个协议是适合于检测单核苷酸多态性，转基因，和基因突变，包括SIngle碱基对的改变，插入或缺失。

<table border="0" cellpadding="0" cellspacing="0" width="842">
	<colgroup>
		<col />
		<col />
		<col />
		<col />
		<col />
	</colgroup>
	<tbody>
		<tr height="42">
			<td height="42" style="height:42px;width:232px;">100 Reaction LightScanner Master Mix</td>
			<td style="width:145px;">BioFire</td>
			<td style="width:141px;">HRLS-ASY-0002</td>
			<td style="width:157px;">www.biofiredx.com</td>
			<td style="width:167px;">Store at -20 &#176;C&#160;</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:232px;">Hard-Shell PCR 96-well BLK/WHT Plates</td>
			<td style="width:145px;">Bio-Rad Laboratories</td>
			<td style="width:141px;">HSP9665</td>
			<td>www.bio-rad.com</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:232px;">Microseal &#39;B&#39; Adhesive Seals</td>
			<td style="width:145px;">Bio-Rad Laboratories</td>
			<td style="width:141px;">MSB1001</td>
			<td>www.bio-rad.com</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:232px;">96-Well LightScanner Instrument</td>
			<td style="width:145px;">BioFire</td>
			<td style="width:141px;">LSCN-ASY-0040</td>
			<td>www.biofiredx.com</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:232px;">LightScanner Software with Call-IT 2.0</td>
			<td style="width:145px;">BioFire</td>
			<td style="width:141px;"></td>
			<td>www.biofiredx.com</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:232px;">High-Resolution Melting Analysis 2.0</td>
			<td style="width:145px;">BioFire</td>
			<td style="width:141px;"></td>
			<td>www.biofiredx.com</td>
			<td></td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:232px;">LightScanner Primer Design Software</td>
			<td style="width:145px;">BioFire</td>
			<td style="width:141px;"></td>
			<td>www.biofiredx.com</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:232px;">Vector NTI Software</td>
			<td style="width:145px;">Invitrogen</td>
			<td style="width:141px;"></td>
			<td>www.invitrogen.com</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:232px;">Tricaine</td>
			<td style="width:145px;"></td>
			<td style="width:141px;"></td>
			<td style="width:157px;"></td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:232px;">Paraformaldehyde</td>
			<td style="width:145px;"></td>
			<td style="width:141px;"></td>
			<td style="width:157px;"></td>
			<td></td>
		</tr>
	</tbody>
</table>

rapid and efficient zebrafish genotyping using pcr with high-resolution melt analysis

斑马鱼是研究开发，造型疾病，并进行药物筛选功能强大的脊椎动物模型系统。最近的各种遗传工具的相继出台，其中包括诱导突变并产生转基因株系多种策略。然而，大规模的筛选是通过传统的基因分型方法，这是耗时耗力的限制。在这里，我们描述的技术来分析斑马鱼的基因型PCR结合高分辨率熔解分析（HRMA）。这种方法快速，灵敏，而且价格便宜，具有污染器物风险较低。基因分型的PCR与HRMA可以用于胚胎或成年鱼，包括高通量筛选的协议。

可以在一天内进行，或在步骤分离出的协议数天（工作的流程图示于图1）。 DNA提取之后，通过PCR扩增子的熔化和分析。的温度为扩增子的熔化取决于大小和GC含量，但一般就50˚C和95˚C端的温度是适当的（ 图2A和2B）。一旦熔体被执行时，荧光熔融曲线的分析通常需要不同的样本曲线的变化的归一化，使用前和后的熔融区域作为标准（ 图2C）。这?...

Watch this Scientific Journal Video about Rapid and Efficient Zebrafish Genotyping Using PCR with High-resolution Melt Analysis at JoVE.com

Rapid and Efficient Zebrafish Genotyping Using PCR with High-resolution Melt Analysis

PCR结合高分辨率的熔融分析（HRMA）被证明是一种快速，有效的方法，以斑马鱼的基因型。

快速，高效的斑马鱼基因分型采用PCR与高分辨率熔体分析

Zebrafish is a powerful vertebrate model system for studying development, modeling disease, and performing drug screening. Recently a variety of genetic ...

rapid-efficient-zebrafish-genotyping-using-pcr-with-high-resolution

Universidad de Cartagena UDEC

Research

JoVE Journal

Biology

22.1K 次观看.  University of Utah School of Medicine.  PCR结合高分辨率的熔融分析（HRMA）被证明是一种快速，有效的方法，以斑马鱼的基因型。 

视频: Rapid and Efficient Zebrafish Genotyping Using PCR with High-resolution Melt Analysis

Rapid Genotyping of Mouse Tissue Using Sigma's Extract-N-Amp Tissue PCR Kit

Genomic detection of DNA via PCR amplification and detection on an electrophoretic gel is a standard way that the genotype of a tissue sample is determined. Conventional preparation of tissues for PCR-ready DNA often take several hours to days, depending on the tissue sample. The genotype of the sample may thus be delayed for several days, which is not an option for many different types of experiments. Here we demonstrate the complete genotyping of a mouse tail sample, including tissue digestion and PCR readout, in one and a half hours using Sigma's SYBR Green Extract-N-Amp Tissue PCR Kit. First, we demonstrate the fifteen-minute extraction of DNA from the tissue sample. Then, we demonstrate the real time read-out of the PCR amplification of the sample, which allows for the identification of a positive sample as it is being amplified. Together, the rapid extraction and real-time readout allow for a prompt identification of genotype of a variety different types of tissues through the reliable method of PCR.

The complete genotyping of a mouse tail sample, including tissue digestion and PCR readout, is done in one and a half hours using Sigma's SYBR Green Extract-N-Amp Tissue PCR kit.

使用Sigma的提取物N -安培组织PCR试剂盒小鼠组织的快速基因分型

Genomic detection of DNA via PCR amplification and detection on an electrophoretic gel is a standard way that the genotype of a tissue sample is ...

科研

生物学

Zebrafish Whole Mount High-Resolution Double Fluorescent In Situ Hybridization

Whole mount in situ hybridization is one of the most widely used techniques in developmental biology. Here, we present a high-resolution double fluorescent in situ hybridization protocol for analyzing the precise expression pattern of a single gene and for determining the overlap of the expression domains of two genes. The protocol is a modified version of the standard in situ hybridization using alkaline phosphatase and substrates such as NBT/BCIP and Fast Red 1,2. This protocol utilizes standard digoxygenin and fluorescein labeled probes along with tyramide signal amplification (TSA) 3. The commercially available TSA kits allow flexible experimental design as fluorescence emission from green to far-red can be used in combination with various nuclear stains, such as propidium iodide, or fluorescence immunohistochemistry for proteins. TSA produces a reactive fluorescent substrate that quickly covalently binds to moieties, typically tyrosine residues, in the immediate vicinity of the labeled antisense riboprobe. The resulting staining patterns are high resolution in that subcellular localization of the mRNA can be observed using laser scanning confocal microscopy 3,4. One can observe nascent transcripts at the chromosomal loci, distinguish nuclear and cytoplasmic staining and visualize other patterns such as cortical localization of mRNA. Studies in Drosophila indicate that roughly 70% of mRNAs exhibit specific patterns of subcellular localization that frequently correlate with the function of the encoded protein 5. When combined with computer-aided reconstruction of 3D confocal datasets, our protocol allows the detailed analysis of mRNA distribution with sub-cellular resolution in whole vertebrate embryos.

Zebrafish Whole Mount High-Resolution Double Fluorescent In Situ Hybridization

Whole mount in situ hybridization is one of the most widely used techniques in developmental biology. Here, we present a high-resolution double fluorescent in situ hybridization protocol for analyzing the precise expression pattern of a single gene and for determining the overlap of the expression domains of two genes. We include a propidium iodide nuclear counter-stain to highlight tissue organization.

斑马鱼整装高分辨率双荧光原位杂交

Whole mount in situ hybridization is one of the most widely used techniques in developmental biology.  Here, we present a high-resolution double ...

Rapid PCR Thermocycling using Microscale Thermal Convection

Many molecular biology assays depend in some way on the polymerase chain reaction (PCR) to amplify an initially dilute target DNA sample to a detectable concentration level. But the design of conventional PCR thermocycling hardware, predominantly based on massive metal heating blocks whose temperature is regulated by thermoelectric heaters, severely limits the achievable reaction speed1. Considerable electrical power is also required to repeatedly heat and cool the reagent mixture, limiting the ability to deploy these instruments in a portable format.
Thermal convection has emerged as a promising alternative thermocycling approach that has the potential to overcome these limitations2-9. Convective flows are an everyday occurrence in a diverse array of settings ranging from the Earth's atmosphere, oceans, and interior, to decorative and colorful lava lamps. Fluid motion is initiated in the same way in each case: a buoyancy driven instability arises when a confined volume of fluid is subjected to a spatial temperature gradient. These same phenomena offer an attractive way to perform PCR thermocycling. By applying a static temperature gradient across an appropriately designed reactor geometry, a continuous circulatory flow can be established that will repeatedly transport PCR reagents through temperature zones associated with the denaturing, annealing, and extension stages of the reaction (Figure 1). Thermocycling can therefore be actuated in a pseudo-isothermal manner by simply holding two opposing surfaces at fixed temperatures, completely eliminating the need to repeatedly heat and cool the instrument.
One of the main challenges facing design of convective thermocyclers is the need to precisely control the spatial velocity and temperature distributions within the reactor to ensure that the reagents sequentially occupy the correct temperature zones for a sufficient period of time10,11. Here we describe results of our efforts to probe the full 3-D velocity and temperature distributions in microscale convective thermocyclers12. Unexpectedly, we have discovered a subset of complex flow trajectories that are highly favorable for PCR due to a synergistic combination of (1) continuous exchange among flow paths that provides an enhanced opportunity for reagents to sample the full range of optimal temperature profiles, and (2) increased time spent within the extension temperature zone the rate limiting step of PCR. Extremely rapid DNA amplification times (under 10 min) are achievable in reactors designed to generate these flows.

We describe a novel method to perform DNA replication via the polymerase chain reaction (PCR). Thermal convection is harnessed to continuously shuttle reagents between denaturing, annealing, and extension conditions by maintaining opposing surfaces of the reactor at constant temperature. This inherently simple design promises to make rapid PCR more accessible.

快速PCR热循环利用微型热对流

Many molecular biology assays depend in some way on the polymerase chain reaction (PCR) to amplify an initially dilute target DNA sample to a detectable ...

A PCR-based Genotyping Method to Distinguish Between Wild-type and Ornamental Varieties of Imperata cylindrica

Wild-type I. cylindrica (cogongrass) is one of the top ten worst invasive plants in the world, negatively impacting agricultural and natural resources in 73 different countries throughout Africa, Asia, Europe, New Zealand, Oceania and the Americas1-2. Cogongrass forms rapidly-spreading, monodominant stands that displace a large variety of native plant species and in turn threaten the native animals that depend on the displaced native plant species for forage and shelter. To add to the problem, an ornamental variety [I. cylindrica var. koenigii (Retzius)] is widely marketed under the names of Imperata cylindrica 'Rubra', Red Baron, and Japanese blood grass (JBG). This variety is putatively sterile and noninvasive and is considered a desirable ornamental for its red-colored leaves. However, under the correct conditions, JBG can produce viable seed (Carol Holko, 2009 personal communication) and can revert to a green invasive form that is often indistinguishable from cogongrass as it takes on the distinguishing characteristics of the wild-type invasive variety4 (Figure 1). This makes identification using morphology a difficult task even for well-trained plant taxonomists. Reversion of JBG to an aggressive green phenotype is also not a rare occurrence. Using sequence comparisons of coding and variable regions in both nuclear and chloroplast DNA, we have confirmed that JBG has reverted to the green invasive within the states of Maryland, South Carolina, and Missouri. JBG has been sold and planted in just about every state in the continental U.S. where there is not an active cogongrass infestation. The extent of the revert problem in not well understood because reverted plants are undocumented and often destroyed.
Application of this molecular protocol provides a method to identify JBG reverts and can help keep these varieties from co-occurring and possibly hybridizing. Cogongrass is an obligate outcrosser and, when crossed with a different genotype, can produce viable wind-dispersed seeds that spread cogongrass over wide distances5-7. JBG has a slightly different genotype than cogongrass and may be able to form viable hybrids with cogongrass. To add to the problem, JBG is more cold and shade tolerant than cogongrass8-10, and gene flow between these two varieties is likely to generate hybrids that are more aggressive, shade tolerant, and cold hardy than wild-type cogongrass. While wild-type cogongrass currently infests over 490 million hectares worldwide, in the Southeast U.S. it infests over 500,000 hectares and is capable of occupying most of the U.S. as it rapidly spreads northward due to its broad niche and geographic potential3,7,11. The potential of a genetic crossing is a serious concern for the USDA-APHIS Federal Noxious Week Program. Currently, the USDA-APHIS prohibits JBG in states where there are major cogongrass infestations (e.g., Florida, Alabama, Mississippi). However, preventing the two varieties from combining can prove more difficult as cogongrass and JBG expand their distributions. Furthermore, the distribution of the JBG revert is currently unknown and without the ability to identify these varieties through morphology, some cogongrass infestations may be the result of JBG reverts. Unfortunately, current molecular methods of identification typically rely on AFLP (Amplified Fragment Length Polymorphisms) and DNA sequencing, both of which are time consuming and costly. Here, we present the first cost-effective and reliable PCR-based molecular genotyping method to accurately distinguish between cogongrass and JBG revert.

A PCR-based Genotyping Method to Distinguish Between Wild-type and Ornamental Varieties of Imperata cylindrica

We provide a cost-effective and rapid molecular genotyping protocol that employs variety-specific PCR primers that target DNA sequence differences within the chloroplast trnL-F spacer region to differentiate between varieties of Imperata cylindrica (cogongrass) that cannot be distinguished by morphology alone. These varieties include the federally listed noxious weed, cogongrass and closely-related, wide-spread ornamental variety, I. cylindrica var. koenigii (Japanese blood grass).

一个基于PCR的基因分型方法来区分野生型和观赏品种白茅</em

Wild-type I. cylindrica (cogongrass) is one of the top ten worst invasive plants in the world, negatively impacting agricultural and natural resources in ...

Using High Resolution Computed Tomography to Visualize the Three Dimensional Structure and Function of Plant Vasculature

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique with sub-micron resolution capability that is now being used to evaluate the structure and function of plant xylem network in three dimensions (3D) (e.g. Brodersen et al. 2010; 2011; 2012a,b). HRCT imaging is based on the same principles as medical CT systems, but a high intensity synchrotron x-ray source results in higher spatial resolution and decreased image acquisition time. Here, we demonstrate in detail how synchrotron-based HRCT (performed at the Advanced Light Source-LBNL Berkeley, CA, USA) in combination with Avizo software (VSG Inc., Burlington, MA, USA) is being used to explore plant xylem in excised tissue and living plants. This new imaging tool allows users to move beyond traditional static, 2D light or electron micrographs and study samples using virtual serial sections in any plane. An infinite number of slices in any orientation can be made on the same sample, a feature that is physically impossible using traditional microscopy methods.
Results demonstrate that HRCT can be applied to both herbaceous and woody plant species, and a range of plant organs (i.e. leaves, petioles, stems, trunks, roots). Figures presented here help demonstrate both a range of representative plant vascular anatomy and the type of detail extracted from HRCT datasets, including scans for coast redwood (Sequoia sempervirens), walnut (Juglans spp.), oak (Quercus spp.), and maple (Acer spp.) tree saplings to sunflowers (Helianthus annuus), grapevines (Vitis spp.), and ferns (Pteridium aquilinum and Woodwardia fimbriata). Excised and dried samples from woody species are easiest to scan and typically yield the best images. However, recent improvements (i.e. more rapid scans and sample stabilization) have made it possible to use this visualization technique on green tissues (e.g. petioles) and in living plants. On occasion some shrinkage of hydrated green plant tissues will cause images to blur and methods to avoid these issues are described. These recent advances with HRCT provide promising new insights into plant vascular function.

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique that can be used to study the structure and function of plant vasculature in 3D. We demonstrate how HRCT facilitates exploration of xylem networks across a wide range of plant tissues and species.

使用高解析度电脑断层可视化的三维结构和功能的植物血管

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique with sub-micron resolution capability that is now being ...

Efficient and Rapid Isolation of Early-stage Embryos from Arabidopsis thaliana Seeds

In flowering plants, the embryo develops within a nourishing tissue - the endosperm - surrounded by the maternal seed integuments (or seed coat). As a consequence, the isolation of plant embryos at early stages (1 cell to globular stage) is technically challenging due to their relative inaccessibility. Efficient manual dissection at early stages is strongly impaired by the small size of young Arabidopsis seeds and the adhesiveness of the embryo to the surrounding tissues. Here, we describe a method that allows the efficient isolation of young Arabidopsis embryos, yielding up to 40 embryos in 1 hr to 4 hr, depending on the downstream application. Embryos are released into isolation buffer by slightly crushing 250-750 seeds with a plastic pestle in an Eppendorf tube. A glass microcapillary attached to either a standard laboratory pipette (via a rubber tube) or a hydraulically controlled microinjector is used to collect embryos from droplets placed on a multi-well slide on an inverted light microscope. The technical skills required are simple and easily transferable, and the basic setup does not require costly equipment. Collected embryos are suitable for a variety of downstream applications such as RT-PCR, RNA sequencing, DNA methylation analyses, fluorescence in situ hybridization (FISH), immunostaining, and reporter gene assays.

Efficient and Rapid Isolation of Early-stage Embryos from Arabidopsis thaliana Seeds

We report an efficient and simple method to isolate embryos at early stages of development from Arabidopsis thaliana seeds. Up to 40 embryos can be isolated in 1 hr to 4 hr, depending on the downstream application. The procedure is suitable for transcriptome, DNA methylation, reporter gene expression, immunostaining and fluorescence in situ hybridization analyses.

高效，快速的早期胚胎分离<em&gt;拟南芥</em&gt;种子

In flowering plants, the embryo develops within a nourishing tissue - the endosperm - surrounded by the maternal seed integuments (or seed coat). As a ...

High Resolution Whole Mount In Situ Hybridization within Zebrafish Embryos to Study Gene Expression and Function

This article focuses on whole-mount in situ hybridization (WISH) of zebrafish embryos. The WISH technology facilitates the assessment of gene expression both in terms of tissue distribution and developmental stage. Protocols are described for the use of WISH of zebrafish embryos using antisense RNA probes labeled with digoxigenin. Probes are generated by incorporating digoxigenin-linked nucleotides through in vitro transcription of gene templates that have been cloned and linearized. The chorions of embryos harvested at defined developmental stages are removed before incubation with specific probes. Following a washing procedure to remove excess probe, embryos are incubated with anti-digoxigenin antibody conjugated with alkaline phosphatase. By employing a chromogenic substrate for alkaline phosphatase, specific gene expression can be assessed. Depending on the level of gene expression the entire procedure can be completed within 2-3 days.

High Resolution Whole Mount In Situ Hybridization within Zebrafish Embryos to Study Gene Expression and Function

The zebrafish, a small tropical fish, has become a popular model for studying gene function during vertebrate development and disease. The temporal and spatial expression of target genes can be determined by in situ hybridization. Our improved protocol allows for the detection of low abundant transcripts with low non-specific background signal.

高解析度全山<em&gt;在原位</em杂交斑马鱼胚胎内，研究基因表达和功能

This article focuses on whole-mount in situ hybridization (WISH) of zebrafish embryos. The WISH technology facilitates the assessment of gene expression ...

Rapid Analysis and Exploration of Fluorescence Microscopy Images

Despite rapid advances in high-throughput microscopy, quantitative image-based assays still pose significant challenges. While a variety of specialized image analysis tools are available, most traditional image-analysis-based workflows have steep learning curves (for fine tuning of analysis parameters) and result in long turnaround times between imaging and analysis. In particular, cell segmentation, the process of identifying individual cells in an image, is a major bottleneck in this regard.
Here we present an alternate, cell-segmentation-free workflow based on PhenoRipper, an open-source software platform designed for the rapid analysis and exploration of microscopy images. The pipeline presented here is optimized for immunofluorescence microscopy images of cell cultures and requires minimal user intervention. Within half an hour, PhenoRipper can analyze data from a typical 96-well experiment and generate image profiles. Users can then visually explore their data, perform quality control on their experiment, ensure response to perturbations and check reproducibility of replicates. This facilitates a rapid feedback cycle between analysis and experiment, which is crucial during assay optimization. This protocol is useful not just as a first pass analysis for quality control, but also may be used as an end-to-end solution, especially for screening. The workflow described here scales to large data sets such as those generated by high-throughput screens, and has been shown to group experimental conditions by phenotype accurately over a wide range of biological systems. The PhenoBrowser interface provides an intuitive framework to explore the phenotypic space and relate image properties to biological annotations. Taken together, the protocol described here will lower the barriers to adopting quantitative analysis of image based screens.

Here we describe a workflow for rapidly analyzing and exploring collections of fluorescence microscopy images using PhenoRipper, a recently developed image-analysis platform.

快速分析和荧光显微镜图像的探索

Despite rapid advances in high-throughput microscopy, quantitative image-based assays still pose significant challenges. While a variety of specialized ...

qPCRTag Analysis - A High Throughput, Real Time PCR Assay for Sc2.0 Genotyping

The Synthetic Yeast Genome Project (Sc2.0) aims to build 16 designer yeast chromosomes and combine them into a single yeast cell. To date one synthetic chromosome, synIII1, and one synthetic chromosome arm, synIXR2, have been constructed and their in vivo function validated in the absence of the corresponding wild type chromosomes. An important design feature of Sc2.0 chromosomes is the introduction of PCRTags, which are short, re-coded sequences within open reading frames (ORFs) that enable differentiation of synthetic chromosomes from their wild type counterparts. PCRTag primers anneal selectively to either synthetic or wild type chromosomes and the presence/absence of each type of DNA can be tested using a simple PCR assay. The standard readout of the PCRTag assay is to assess presence/absence of amplicons by agarose gel electrophoresis. However, with an average PCRTag amplicon density of one per 1.5 kb and a genome size of ~12 Mb, the completed Sc2.0 genome will encode roughly 8,000 PCRTags. To improve throughput, we have developed a real time PCR-based detection assay for PCRTag genotyping that we call qPCRTag analysis. The workflow specifies 500 nl reactions in a 1,536 multiwell plate, allowing us to test up to 768 PCRTags with both synthetic and wild type primer pairs in a single experiment.

Designer chromosomes of the Synthetic Yeast Genome project, Sc2.0, can be distinguished from their native counterparts using a PCR-based genotyping assay called PCRTagging, which has a presence/absence endpoint. Here we describe a high-throughput real time PCR detection method for PCRTag genotyping.

qPCRTag分析 - 高通量，实时定量PCR检测方法的基因分型Sc2.0

The Synthetic Yeast Genome Project (Sc2.0) aims to build 16 designer yeast chromosomes and combine them into a single yeast cell. To date one synthetic ...

High-resolution Imaging and Analysis of Individual Astral Microtubule Dynamics in Budding Yeast

Dynamic microtubules are fundamental to many cellular processes, and accurate measurements of microtubule dynamics can provide insight into how cells regulate these processes and how genetic mutations impact regulation. The quantification of microtubule dynamics in metazoan models has a number of associated challenges, including a high microtubule density and limitations on genetic manipulations. In contrast, the budding yeast model offers advantages that overcome these challenges. This protocol describes a method to measure the dynamics of single microtubules in living yeast cells. Cells expressing fluorescently tagged tubulin are adhered to assembled slide chambers, allowing for stable time-lapse image acquisition. A detailed guide for high-speed, four-dimensional image acquisition is also provided, as well as a protocol for quantifying the properties of dynamic microtubules in confocal image stacks. This method, combined with conventional yeast genetics, provides an approach that is uniquely suited for quantitatively assessing the effects of microtubule regulators or mutations that alter the activity of tubulin subunits.

Budding yeast is an advantageous model for studying microtubule dynamics in vivo due to its powerful genetics and the simplicity of its microtubule cytoskeleton. The following protocol describes how to transform and culture yeast cells, acquire confocal microscopy images, and quantitatively analyze microtubule dynamics in living yeast cells.

高分辨率成像和芽殖酵母个人星体微管动力学分析

Dynamic microtubules are fundamental to many cellular processes, and accurate measurements of microtubule dynamics can provide insight into how cells ...

快速，高效的斑马鱼基因分型采用PCR与高分辨率熔体分析

摘要

探索更多视频

此视频中的章节