This work was supported by the LabEx CeLyA of the University of Lyon (ANR-10-LABX-0060 / ANR-11-IDEX-0007).

1. Design of the acoustic levitation chamber
<ol>
	<li>Design an optically transparent (PMMA-like) cubic tank (8 cm edge and 2.8 mm thickness per face) with the geometry module of a multiphysics simulation software (Table of Materials).</li>
	<li>Insert a cylindrical surface (&#216; = 35 mm) centered at the bottom of the tank, to model the ultrasonic transducer.</li>
	<li>Set the boundary conditions to zero pressure on each wall with a normal displacement of amplitude 1 &#181;m at the transducer surface.</li>
	<li>Using a Frequency domain module, simulate the Frequency Response Function (FRF) of the tank in the frequency range [10 - 40] kHz, at the three arbitrary locations loc1 = (0.01375, 0.01375, 0.04125), loc2 = (0, 0, 0.0088), and loc3 = (0.021725, 0.023375, 0.00935).</li>
	<li>Adapt the tank size such that one of the acoustic modes of the cavity corresponds to the nominal frequency of the transducer (here 31.2 kHz). The FRF therefore contains one resonance peak close to this frequency, as illustrated in Figure 3.</li>
	<li>Plot the pressure field inside the tank, as shown in Figure 4. The chosen resonance mode must contain at least one pressure antinode in the inner of the container, on which the acoustic bubble will be trapped.</li>
	<li>When designing the tank, design a movable top face with a guiding groove on each edge to tightly close the tank faces. Drill a tiny hole at the top face in order to fill the tank with the liquid medium.</li>
	<li>Place the water tank atop a homemade frame that contains the ultrasound transducer (Langevin-type, 31.2 kHz nominal frequency). Use echographic gel to couple the transducer to the tank bottom wall.</li>
	<li>Place the tank and frame system atop a three-directions displacement table with micrometric screws.</li>
	<li>Fill the tank with microfiltered, demineralized and water (not degassed, volume ~500mL, oxygen saturation of approximatively 8 mg&#183;L-1). 
	&#8203;NOTE: Using not degassed water instead of degassed makes it possible to maintaining stable bubbles for the duration of experiments. Using degassed water will accelerate bubble shrinking due to gas diffusion, even if slightly counterbalanced by rectified (ultrasound-mediated) diffusion.</li>
</ol>
2. Bubble generation and acoustic calibration
<ol>
	<li>Prepare the experimental setup used for laser-induced bubble nucleation, acoustic excitation and high-speed recording (Figure 5a,b,c). The experimental setup consists of (A) the acoustic levitation system, (B) the laser power supply and (C) the laser head, (D) one spherical concave lens, (E) one plano-concave lens and one aspherical lens, (F) the high-speed camera, (G) the continuous light-emitting diode. Later, for measurements of liquid flows (Figure 5d) (H) one continuous wave laser source, (I) a cylindrical plano-concave lens followed by a cylindrical plano-concave lens inserted behind the first lens and oriented on the orthogonal axis will be added.</li>
	<li>Plug the ultrasound transducer to a function generator. Set the excitation signal as: sinusoidal waveform, continuous wave, frequency 31.2 kHz. The amplitude is the only variable parameter.</li>
	<li>Place the lens (D) at a distance of approximatively 6 cm in front of the laser head (C).</li>
	<li>Place the lens (E) at a distance of approximatively 12 cm in front of the lens (D).</li>
	<li>Place the water tank (A) such that a focusing point of the laser is located inside the water tank, leading to spark generation for every laser pulse (5 -10 mJ). The laser spark should be located approximately 3 cm below the targeted pressure antinode. 
	NOTE: Without ultrasound (US), laser-nucleated bubble will rise to the top face due to buoyancy.</li>
	<li>Switch on the ultrasound transducer. Increase the applied voltage until the bubble no longer rises vertically but is deviated towards the pressure antinode and, for a sufficient high pressure, trapped.</li>
	<li>Set the backlit illumination (continuous light-emitting diode) and the high-speed camera in order to observe the trapped bubble. 
	NOTE: When nucleating a new bubble with a laser spark, it is easy to capture the trajectory of the bubble approaching its trapping location.</li>
	<li>Move the location of the laser spark within the water tank such that the bubble trajectory remains inside the focal plane of the camera.</li>
	<li>Trap one bubble and capture its radial oscillations with the following parameters: frame size 128 x 128 pixels, acquisition rate 180 kHz. An example of large-amplitude radial oscillations over two acoustic periods is provided in Figure 6. Typical gas bubbles size ranges from 30 to 80 &#181;m.</li>
	<li>Record the bubble radial oscillations during 3 to 30 milliseconds in order to capture hundreds to thousands of bubble oscillations. Repeat this recording for increasing applied voltages of the transducer. Typical applied voltages are in the range of 0 - 8 V. 
	NOTE: When modifying the applied voltage, the equilibrium location of the trapped bubble slightly moves vertically. To follow the oscillations without moving the backlit illumination and camera, place the system (transducer and water tank) onto a three-directions movable table with micrometric accuracy.</li>
	<li>Switch on the ultrasound transducer and capture one image of the background for post-analysis.</li>
	<li>Post-process the video series following this procedure:
	<ol>
		<li>Run the executable file VoltagePressure.exe. The interface shown in Figure 7 should open. 
		NOTE: The script is available as a supplementary document.</li>
		<li>Specify the physical and experimental parameters in the left column (Figure 7A).</li>
		<li>Specify the values of applied voltage for the series of recordings in the bottom-right table (Figure 7B).</li>
		<li>In the Bubble radius analysis panel, click on Load parameters (Figure 7C) and select the folder containing all the files of your video series, and then the background image (mandatory).</li>
		<li>The choice is allowed between analyzing all the videos at once, by clicking on Auto, or one-by-one by clicking on Step by step.</li>
		<li>For each video file, the evolution of the bubble radius is plotted over one acoustic period, and a numerical fit is superimposed. The red curve corresponds to a linearized Rayleigh-Plesset modeling. The equilibrium bubble radius is displayed (Figure 7D).</li>
		<li>According to the numerical fitting, the applied pressure for this voltage is displayed in the Pressure (Voltage) graph panel (Figure 7E). The value of the applied pressure is also displayed in the bottom-right table (Figure 7B). Typical applied pressures corresponding to the 0 - 8 V voltage dynamics are 0 - 25 kPa.</li>
		<li>Once all videos are processed, click on the Linear regression button to perform a linear fit of the pressure/voltage curve. The data (voltage and pressure values) are saved into a .txt file located in the current directory. The slope of the fit is provided.</li>
	</ol>
	</li>
</ol>
3. Coalescence technique
<ol>
	<li>Switch on the ultrasound transducer. Set the applied voltage high enough such that the corresponding acoustic pressure may lead to the triggering of surface instability, according to the numerical pressure/radius diagram of instability zones, as shown in Figure 8.</li>
	<li>Nucleate a bubble, which will then migrate to its trapping location. If the trapped bubble only exhibits spherical oscillations, move on to the next step. If nonspherical oscillations appear:
	<ol>
		<li>Switch off the ultrasound power to let the bubble rise to the top surface.</li>
		<li>Modify the laser energy (by finely tuning over a few mJ) or reduce the transducer voltage.</li>
		<li>Switch on the ultrasound power.</li>
		<li>Nucleate a new bubble.</li>
		<li>Repeat this procedure until the bubble size leads to purely spherical oscillations.</li>
	</ol>
	</li>
	<li>When a trapped bubble exhibits only spherical oscillations, generate a new laser spark. When the new bubble reaches the trapping location, coalescence occurs.</li>
	<li>If the coalesced bubble exhibits only spherical oscillations, generate a new bubble. Multiple coalescences may be necessary to reach the bubble radius at which nonspherical deformations occur. An example of bubble coalescence leading to nonspherical oscillations is shown in Figure 9.</li>
	<li>Once the coalesced bubble exhibits nonspherical oscillations, record the bubble oscillations for a duration of approximatively 3 to 30 milliseconds.</li>
	<li>Identify the mode number of shape oscillations by referring to Figure 10.</li>
</ol>
4. Fluid flow measurements
<ol>
	<li>In the case of cavitation microstreaming measurements, fluorescent tracer particles must be added to the water prior to bubble nucleation. In this study, 0.71 &#181;m particles are used (Table of Materials). They are sufficiently small to be acoustically transparent (not influenced by the acoustic radiation force) and to accurately follow the flow as well as sufficiently large to scatter laser light. Use three drops for the volume of the water tank, corresponding to approximatively 2.104 particles/mm3.</li>
	<li>Prior to taking measurements, set the following parameters for capturing both the (fast timescale) bubble dynamics and (low timescale) fluid flow:
	<ol>
		<li>Create a partitioning of the camera recording disk.</li>
		<li>Alternatively define the recording parameters as:
		<ol>
			<li>Frame rate 180 kHz, frame size 128 x 128 pixels, and exposure time 1 &#181;s for one recording of the dynamics of the bubble interface</li>
			<li>Frame rate 600 Hz, frame size 1024 x 768 pixels, and exposure time 1 ms for one recording of the motion of dye tracers.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Use a continuous laser.</li>
	<li>Create a thin laser sheet by successively letting the laser beam pass through cylindrical plano-concave lens and cylindrical plano-convex lens oriented on an orthogonal axis. A beam width of about 160 &#181;m can be obtained.</li>
	<li>Set up the laser sheet to correspond to the imaging plane:
	<ol>
		<li>Set the laser on a movable device so that the laser sheet can be moved parallel to the imaging plane.</li>
		<li>Adjust the position so that the illuminated particles are visible by the camera.</li>
		<li>Nucleate and trap a bubble.</li>
		<li>Adjust the position of the laser sheet further, so that a shadow becomes visible behind the bubble. The bubble is now inside the laser sheet, as shown in Figure 11.</li>
	</ol>
	</li>
	<li>Induce bubble coalescence until a stably oscillating shape mode is apparent.</li>
	<li>Do several recordings switching back and forth between bubble dynamics and microstreaming. 
	&#8203;NOTE: Switch off the continuous laser when not needed. Heating can create unwanted convective flows. Also, turn off the light-emitting diode when performing the measurements of streaming flow.</li>
</ol>
5. Image processing to visualize the cavitation microstreaming patterns
<ol>
	<li>Install the visualization software ImageJ for image processing and analysis in Java. Also install the plugin CINE File Reader in order to open the high-speed camera files.</li>
	<li>Click on File | Import | CineFile and select the video *.cine containing the capture of the particle motion.</li>
	<li>Select Use virtual stack in the new window, the video is now loaded.</li>
	<li>In order to observe the particle motion without displaying the streaming pattern, click on Image | Adjust | Brightness/Contrast | Auto. The dark background is now replaced by an automatically optimized image.</li>
	<li>In order to display the resulting pattern, click on Image | Stacks | Z Project and choose the Max Intensity option for the image projection. An output image with pixels containing the maximum value over all images in the stack is displayed. Adjust the image contrast as described in step 5.4, if necessary. 
	NOTE: A streaming pattern such as the ones shown in Figure 12b and Figure 12d is obtained.</li>
</ol>

<ol>
	<li>Roovers, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+role+of+ultrasound-driven+microbubble+dynamics+in+drug+delivery:+from+microbubble+fundamentals+to+clinical+translation.">The role of ultrasound-driven microbubble dynamics in drug delivery: from microbubble fundamentals to clinical translation.</a> Langmuir. 35 (31), 10173-10191 (2019).</li><li>Liu, H. L., Fan, C. H., Ting, C. Y., Yeh, C. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Combining+microbubbles+and+ultrasound+for+drug+delivery+to+brain+tumors:+current+progress+and+overview.">Combining microbubbles and ultrasound for drug delivery to brain tumors: current progress and overview.</a> Theranostics. 4 (4), 432-444 (2014).</li><li>Lammertink, B. H. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sonochemotherapy:+from+bench+to+bedside.">Sonochemotherapy: from bench to bedside.</a> Frontiers in Pharmacology. 6, 138 (2015).</li><li>Lajoinie, G., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+vitro+methods+to+study+bubble-cell+interactions:+fundamentals+and+therapeutic+applications.">In vitro methods to study bubble-cell interactions: fundamentals and therapeutic applications.</a> Biomicrofluidics. 10, 011501 (2016).</li><li>Van Wamel, A., Bouakaz, A., Versluis, M., de Jong, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Micromanipulation+of+endothelial+cells:+ultrasound-microbubble-cell+interaction.">Micromanipulation of endothelial cells: ultrasound-microbubble-cell interaction.</a> Ultrasound in Medicine and Biology. 30, 1255-1258 (2004).</li><li>Tran, T. A., Roger, S., Le Guennec, J. Y., Tranquart, F., Bouakaz, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+ultrasound-activated+microbubbles+on+the+cell+electrophysiological+properties.">Effect of ultrasound-activated microbubbles on the cell electrophysiological properties.</a> Ultrasound in Medicine and Biology. 33, 158-163 (2007).</li><li>Marmottant, P., Hilgenfeldt, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Controlled+vesicle+deformation+and+lysis+by+single+oscillating+bubbles.">Controlled vesicle deformation and lysis by single oscillating bubbles.</a> Nature. 423 (6936), 153-156 (2003).</li><li>Prentice, P. A., Cuschieri, K., Dholakia, K., Prausnitz, M., Campbell, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Membrane+disruption+by+optically+controlled+microbubble+cavitation.">Membrane disruption by optically controlled microbubble cavitation.</a> Nature Physics. 1, 107-110 (2005).</li><li>Kudo, N., Okada, K., Yamamoto, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sonoporation+by+single-shot+pulsed+ultrasound+with+microbubbles+adjacent+to+cells.">Sonoporation by single-shot pulsed ultrasound with microbubbles adjacent to cells.</a> Biophysical Journal. 96, 4866-4876 (2009).</li><li>Novell, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+safety+index+based+on+intrapulse+monitoring+of+ultra-harmonic+cavitation+during+ultrasound-induced+blood-brain+barrier+opening+procedures.">A new safety index based on intrapulse monitoring of ultra-harmonic cavitation during ultrasound-induced blood-brain barrier opening procedures.</a> Scientific Reports. 10, 10088 (2020).</li><li>Cornu, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrafast+monitoring+and+control+of+subharmonic+emissions+of+an+unseeded+bubble+cloud+during+pulsed+sonication.">Ultrafast monitoring and control of subharmonic emissions of an unseeded bubble cloud during pulsed sonication.</a> Ultrasonics Sonochemistry. 42, 697-703 (2018).</li><li>Reslan, L., Mestas, J. L., Herveau, S., B&#233;ra, J. C., Dumontet, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transfection+of+cells+in+suspension+by+ultrasound+cavitation.">Transfection of cells in suspension by ultrasound cavitation.</a> Journal of Controlled Release. 142 (2), 251-258 (2010).</li><li>Reuter, F., Gonzalez-Avila, S. R., Mettin, R., Ohl, C. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Flow+fields+and+vortex+dynamics+of+bubbles+collapsing+near+a+solid+boundary.">Flow fields and vortex dynamics of bubbles collapsing near a solid boundary.</a> Physical Review Fluids. 2, 064202 (2017).</li><li>Chew, L. W., Klaseboer, E., Ohl, S. W., Khoo, B. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Interaction+of+two+differently+sized+oscillating+bubbles+in+a+free+field.">Interaction of two differently sized oscillating bubbles in a free field.</a> Physical Review E. 84, 066307 (2011).</li><li>Doinikov, A. A., Bouakaz, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustic+microstreaming+around+a+gas+bubble.">Acoustic microstreaming around a gas bubble.</a> The Journal of the Acoustical Society of America. 127 (2), 703-709 (2010).</li><li>Tho, P., Manasseh, R., Ooi, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cavitation+microstreaming+patterns+in+single+and+multiple+bubble+systems.">Cavitation microstreaming patterns in single and multiple bubble systems.</a> Journal of Fluid Mechanics. 576, 191-233 (2007).</li><li>Van Wamel, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vibrating+microbubbles+poking+individual+cells:+Drug+transfer+into+cells+via+sonoporation.">Vibrating microbubbles poking individual cells: Drug transfer into cells via sonoporation.</a> Journal of Controlled Release. 112, 149-155 (2006).</li><li>Helfield, B., Chen, X., Watkins, S. C., Villanueva, F. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Biophysical+insight+into+mechanisms+of+sonoporation.">Biophysical insight into mechanisms of sonoporation.</a> PNAS. 113 (36), 9983-9988 (2016).</li><li>Pereno, V., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Layered+acoustofluidic+resonators+for+the+simultaneous+optical+and+acoustic+characterization+of+cavitation+dynamics,+microstreaming,+and+biological+effects.">Layered acoustofluidic resonators for the simultaneous optical and acoustic characterization of cavitation dynamics, microstreaming, and biological effects.</a> Biomicrofluidics. 12, 034109 (2018).</li><li>Shklyaev, S., Straube, A. V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Linear+oscillations+of+a+compressible+hemispherical+bubble+on+a+solid+substrate.">Linear oscillations of a compressible hemispherical bubble on a solid substrate.</a> Physics of Fluids. 20, 052102 (2008).</li><li>Fauconnier, M., Bera, J. C., Inserra, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nonspherical+modes+non-degeneracy+of+a+tethered+bubble.">Nonspherical modes non-degeneracy of a tethered bubble.</a> Physical Review E. 102, 033108 (2020).</li><li>Xi, X., Cegla, F., Mettin, R., Holsteyns, F., Lippert, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Study+of+non-spherical+bubble+oscillations+near+a+surface+in+a+weak+acoustic+standing+wave+field.">Study of non-spherical bubble oscillations near a surface in a weak acoustic standing wave field.</a> The Journal of the Acoustical Society of America. 135, 1731 (2014).</li><li>Doinikov, A. A., Bouakaz, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+a+distant+rigid+wall+on+microstreaming+generated+by+an+acoustically+driven+gas+bubble.">Effect of a distant rigid wall on microstreaming generated by an acoustically driven gas bubble.</a> Journal of Fluid Mechanics. 742, 425-445 (2014).</li><li>Cleve, S., Gu&#233;dra, M., Inserra, C., Mauger, C., Blanc-Benon, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Surface+modes+with+controlled+axisymmetry+triggered+by+bubble+coalescence+in+a+high-amplitude+acoustic+field.">Surface modes with controlled axisymmetry triggered by bubble coalescence in a high-amplitude acoustic field.</a> Physical Review E. 98, 033115 (2018).</li><li>Lamb, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Hydrodynamics. 6th ed. , (1932).</li><li>Liu, Y., Wang, Q. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Stability+and+natural+frequency+of+nonspherical+mode+of+an+encapsulated+microbubble+in+a+viscous+liquid.">Stability and natural frequency of nonspherical mode of an encapsulated microbubble in a viscous liquid.</a> Physics of Fluids. 28, 062102 (2016).</li><li>Dollet, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nonspherical+oscillations+of+ultrasound+contrast+agent+microbubbles.">Nonspherical oscillations of ultrasound contrast agent microbubbles.</a> Ultrasound in Medicine and Biology. 34 (9), 1465-1473 (2008).</li><li>Versluis, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microbubble+shape+oscillations+excited+through+ultrasonic+parametric+driving.">Microbubble shape oscillations excited through ultrasonic parametric driving.</a> Physical Review E. 82, 026321 (2010).</li><li>Gu&#233;dra, M., Cleve, S., Mauger, C., Blanc-Benon, P., Inserra, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dynamics+of+nonspherical+microbubble+oscillations+above+instability+threshold.">Dynamics of nonspherical microbubble oscillations above instability threshold.</a> Physical Review E. 96, 063104 (2017).</li><li>Cleve, S., Gu&#233;dra, M., Mauger, C., Inserra, C., Blanc-Benon, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microstreaming+induced+by+acoustically+trapped,+non-spherically+oscillating+microbubbles.">Microstreaming induced by acoustically trapped, non-spherically oscillating microbubbles.</a> Journal of Fluid Mechanics. 875, 597-621 (2019).</li><li>Doinikov, A. A., Cleve, S., Regnault, G., Mauger, C., Inserra, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustic+microstreaming+produced+by+nonspherical+oscillations+of+a+gas+bubble.+I.+Case+of+modes+0+and+m.">Acoustic microstreaming produced by nonspherical oscillations of a gas bubble. I. Case of modes 0 and m.</a> Physical Review E. 100, 033104 (2019).</li><li>Inserra, C., Regnault, G., Cleve, S., Mauger, C., Doinikov, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustic+microstreaming+produced+by+nonspherical+oscillations+of+a+gas+bubble.+III.+Case+of+self-interacting+modes+n-n.">Acoustic microstreaming produced by nonspherical oscillations of a gas bubble. III. Case of self-interacting modes n-n.</a> Physical Review E. 101, 013111 (2020).</li><li>Prabowo, F., Ohl, C. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Surface+oscillations+and+jetting+from+surface+attached+acoustic+driven+bubbles.">Surface oscillations and jetting from surface attached acoustic driven bubbles.</a> Ultrasonics Sonochemistry. 18 (1), 431-435 (2011).</li><li>Garbin, V., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Changes+in+microbubble+dynamics+near+a+boundary+revealed+by+combined;+optical+micromanipulation+and+high-speed+imaging.">Changes in microbubble dynamics near a boundary revealed by combined; optical micromanipulation and high-speed imaging.</a> Applied Physics Letters. 90, 114103 (2007).</li><li>Collis, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cavitation+microstreaming+and+stress+fields+created+by+microbubbles.">Cavitation microstreaming and stress fields created by microbubbles.</a> Ultrasonics. 50, 273-279 (2010).</li><li>Loughran, J., Eckersley, R. J., Tang, M. X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modeling+non-spherical+oscillations+and+stability+of+acoustically+driven+shelled+microbubbles.">Modeling non-spherical oscillations and stability of acoustically driven shelled microbubbles.</a> The Journal of the Acoustical Society of America. 131 (6), 4349-4357 (2012).</li><li>Vos, H. J., Dollet, B., Bosch, J. G., Versluis, M., de Jong, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nonspherical+vibrations+of+microbubbles+in+contact+with+a+wall+-+a+pilot+study+at+low+mechanical+index.">Nonspherical vibrations of microbubbles in contact with a wall - a pilot study at low mechanical index.</a> Ultrasound in Medicine and Biology. 34 (4), 685-688 (2008).</li><li>Regnault, G., Mauger, C., Blanc-Benon, P., Inserra, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Secondary+radiation+force+between+two+closely+spaced+acoustic+bubbles.">Secondary radiation force between two closely spaced acoustic bubbles.</a> Physical Review E. 102, 031101 (2020).</li></ol>

The authors have nothing to disclose.

The presented procedure consists of using bubble coalescence in order to trigger steady-state, symmetry-controlled bubble shape oscillations, allowing the study of the long-term fluid flow induced by these oscillations. The main challenge in the technique is the control of nonspherical oscillations for a bubble being trapped, far from any boundaries.
Most of the existing techniques proposed in the literature focused on substrate-attached bubbles7,<sup class="...

In medicine, an administered drug must penetrate many obstacles in the living system before reaching the desired targets. However, most drugs are rapidly cleaned away from the blood stream. The targeting efficiency is low and they cannot easily cross cell membranes, leading to ineffective drug delivery. Currently, the use of microbubbles in combination with ultrasound has been proposed as an innovative method for noninvasive, precise and targeted delivery of drugs and genes to pathological tissues and cells1. In this approach, microbubbles can play a role as carriers where free drugs are either co-injected with a gas bubble suspension or loaded on its surface. Microbubbles can also act as a local vector for refocusing the ultrasound energy in order to interact with the cells. Basically, under ultrasound exposure, bubbles stably compress and expand, a regime called stable cavitation that generates liquid flows and hence shear stress on nearby objects. Microbubbles may also oscillate non-linearly and expand until collapse, in the regime of inertial cavitation, producing shock waves that propagate radially from the collapse site2. It has been shown that cavitation, either stable or inertial, enhances the permeabilization of cell membranes, and thus enhances the internalization of drugs into the cell3.
In therapeutic applications, understanding the mechanism of the bubble-cell interaction is very important, but there are several barriers, both from scientific and technical sides, that prevent our knowledge from advancing. First, capturing the dynamics of cells in response to bubble-induced mechanical stimuli is very difficult4. At the acoustic timescale, the first-order microbubble oscillations can lead to activation of membrane channels, facilitating molecular passage across biological interfaces. This occurs through the direct oscillation of the cell membrane, also called &#34;cellular massage&#34;5. Channel activation following direct mechanical stress was evidenced using patch-clamp techniques that measured electrophysiological properties of cell membranes during and after ultrasound exposure6. Measuring bubble-induced cell dynamics (meaning the complete field of deformation of the cell membrane) at the acoustic timescale, would also provide insights in the threshold of membrane area expansion &#916;A/A required to induce pores into the cell membrane7. The second barrier is controlling the collapsing bubble regime to avoid microbubble-induced cell lysis. Bubble collapses and induced microjets have been identified as a mechanism through which membrane perforation occurs8,9. Once permeabilized, the cell membrane repairs through calcium self-sealing of the lipid bilayers and fusion of intracellular vesicles9. The occurrence of bubble collapses may also cause lethal damages to the cell and induce unnecessary side effects in the surrounding ones. In sensitive applications such as ultrasound-mediated blood-brain barrier opening, it is generally accepted that inertial bubble collapses should be avoided10.
Therefore, huge efforts are currently devoted to the design of ultrasound emission sequences, coupled with passive cavitation monitoring and control, in order to ensure stable oscillations of microbubbles11. In this stable regime, it has been hypothesized that stably oscillating bubbles play a strong role in the triggering of membrane permeabilization by promoting spatially-targeted shear stress on the cell membrane7. The shear stress results from the liquid flows created in the vicinity of the oscillating bubbles. These liquid flows are called cavitation microstreaming, and, as mentioned above, they are one of the several possible mechanisms which are responsible for enhanced uptake of extracellular molecules. When dealing with suspension of bubbles or cells such as in-vitro biological transfections assays12, permeabilization by microstreaming might be much more efficient than permeabilization by bubble collapse. This can be shown by a simple geometrical consideration. In cell suspensions, sonoporation will be efficient if the majority of the suspended cells is submitted to sufficiently large mechanical effects (leading to membrane permeabilization). It is known that bubble collapses are directed along the direction of isotropic symmetry breaking, such as the bubble-wall axis13 or the bubble-bubble and bubble-cell line joining their center of mass14. The produced microjet is therefore a spatially-localized phenomenon along a finite number of lines joining the cell and bubble centers. Depending on the cell and bubble concentration, as well as the bubble-cell distance, this effect may not be the most efficient to permeabilize the whole number of suspended cells. In contrast, cavitation microstreaming is a phenomenon occurring at a slow timescale, with a large spatial expansion in comparison to the bubble radius. Also, the liquid flow is distributed all around the bubble, and may therefore impacts a larger number of cells, at a very long range. Therefore, understanding the generated cavitation microstreaming around an oscillating bubble is a prerequisite for controlling and quantifying the bubble-induced shear stress that is applied to cells.
To do so, a preliminary step consists in controlling the spherical and nonspherical oscillations of an ultrasound-driven bubble, as the generated liquid flows are induced by the motion of the bubble interface15,16. In particular, shape oscillations of microbubbles have to be triggered and kept stable. Furthermore, the orientation of the bubble shape oscillations has to be controlled to properly analyze the correlation between the bubble interface dynamics and the induced microstreaming pattern. When summarizing the existing literature, it is obvious that detailed experimental results of cavitation-induced microstreaming are only available for bubbles attached to a surface. Wall-attached microbubbles are commonly-used for assessing accurate interface dynamics and cell interactions at the micrometer scale under an ultrafast microscopy system. This configuration is therapeutically relevant when considering vibrating microbubbles located on the cell membrane17,18,19. The study of substrate-attached bubble may however make the analysis of bubble dynamics more complicated, partly due to the complex nature of contact line dynamics20, and the triggering of asymmetric shape modes21. In medical and biological applications, bubbles that are not attached to a wall are commonly found in confined geometries such as small vessels. This impacts significantly bubble dynamics and shape instabilities. Particularly, the presence of a nearby wall shifts the pressure threshold for shape mode triggering to lower pressure values depending on the shape mode number and bubble size22. The wall also affects the bubble-induced microstreaming with possibly higher intensity for the produced flow23.
Amongst all the possible scenario that microbubbles may experience (free or attached, close to a wall, collapsing or stably-oscillating), we propose to investigate the nonspherical dynamics of a single bubble far from any boundary. The experimental setup is based on an acoustic levitation system24 in which a standing ultrasound wave is used to trap the bubble. This scenario is consistent with medical applications in which a collection of suspended bubbles and cells coexist in a sonotransfection chamber, for instance. As far as bubbles and cells are not too close, it is assumed that the presence of a cell does not impact the bubble interface dynamics. When cells follow the loop-like trajectories of the cavitation-induced microstreaming, they are cyclically approaching and repelling from the bubble location and we can assume that the cell presence impacts neither the streaming pattern nor its mean velocity. In addition, nonspherical dynamics and induced microstreaming from single bubbles far from boundary are well known from a theoretical point of view. In order to link the bubble-induced liquid flow to the bubble contour dynamics, it is required to accurately characterize the bubble interface dynamics. To do so, it is preferable to adapt the spatiotemporal scale in experimental studies with respect to those used in therapeutics so that acquisition with common high-speed cameras (below 1 million frame/second) is possible by using large bubbles excited at lower frequencies. When considering uncoated bubbles, the eigenfrequency &#969;n of a given mode n is related to the bubble size as <img alt="Equation 1" src="/files/ftp_upload/62044/62044eq1.jpg" /> 25. This radius-eigenfrequency relationship is slightly modified when considering shelled bubbles26, but the order of magnitude of the eigenfrequency &#969;n remains the same. Thus, investigating bubbles with equilibrium radii ~50&#956;m in a 30 kHz ultrasound field is similar to studying coated bubbles of radii ~3&#956;m in a 1.7 MHz field, as proposed by Dollet et al.27. Similar shape mode numbers and hence microstreaming patterns are therefore expected.
In order to trigger nonspherical oscillations of the bubble interface, it is necessary to exceed a certain pressure threshold that is radius-dependent, as shown in Figure 1. Existing experimental techniques rely on the increase of the acoustic pressure to trigger surface modes (illustrated by path (1) in Figure 1), either by step-by-step pressure increase28 or by modulated-amplitude excitation responsible of periodic onset and extinction of surface modes29. The main drawbacks of these techniques are (i) a random orientation of the symmetry axis of the surface oscillations that cannot be controlled to be in the imaging plane, (ii) a short lifetime of the bubble shape oscillations that makes the analysis of the induced liquid flows difficult at larger timescales, and (iii) the frequent triggering of unstable shape modes. We propose an alternative technique to cross the pressure threshold at a constant acoustic pressure in the radius/pressure map, as illustrated by the path (2) in Figure 1. To do so, it is required to increase the bubble size such that it will be in the instability zone. Such an increase is performed by a bubble coalescence technique. The coalescence of two, initially spherically-oscillating, microbubbles is exploited to create one single deformed bubble. If the acoustic pressure and bubble size of the coalesced bubble are in the instability zone, surface modes are triggered. We also evidenced that the coalescence technique induces stable shape oscillations in a steady-state regime, as well as a controlled symmetry axis defined by the rectilinear motion of the two approaching bubbles. Because a stable shape oscillation is ensured over minutes, the analysis of bubble-induced fluid flow is possible by seeding the liquid medium with fluorescent microparticles, lighted by a thin laser sheet. Recording the motion of the solid microparticles in the vicinity of the bubble interface allows identifying the pattern of the induced fluid flow30. The overall principle of the triggering of bubble shape oscillations, leading to a time-stable fluid flow, is illustrated in Figure 2.
In the following protocol, we outline the steps required to create stable bubble shape oscillations via the coalescence technique and describe the measurements of fluid flow. This includes the design of the acoustic levitation system, the acoustic calibration, bubble nucleation and the coalescence technique, the measurement of bubble interface dynamics and surrounding fluid flow, and the image processing.

<table><tbody><tr><td>Aspherical lens</td><td>Thorlabs</td><td>AL4050</td><td>Lens of focus 40 mm</td></tr><tr><td>Continuous wave laser source</td><td>CNI</td><td>MLL6FN</td><td>DPSS laser of wavelength 532nm, energy 400 mW</td></tr><tr><td>Cylindrical plano-concave lens</td><td>Thorlabs</td><td>LJ1277L1-A</td><td>lens of focus -25?4mm</td></tr><tr><td>Cylindrical plano-concave lens</td><td>Thorlabs</td><td>LK1900L1</td><td>lens of focus 250 mm</td></tr><tr><td>Fluorescent particles</td><td>Duke Scientific</td><td>R700</td><td>Red polymer fluorescent microspheres</td></tr><tr><td>Function generator</td><td>Agilent</td><td>HP33120</td><td>Generator of function feeding the ultrasound transducer</td></tr><tr><td>High-speed camera</td><td>Vision Research</td><td>Phantom v12.0</td><td>High-speed recording up to 1 Mfps</td></tr><tr><td>Liquid medium</td><td>Carlo Erba</td><td>Water for analysis</td><td>Demineralized, undegassed water</td></tr><tr><td>Multiphysics software</td><td>Comsol</td><td>None</td><td>Softwate for simulating the acoustic field of the levitation chamber</td></tr><tr><td>Nd:Yag pulsed laser</td><td>New Wave Research</td><td>Solo III-15</td><td>5 ns pulse duration, &amp;lambda;=532 nm, 3.5 mm beam diameter, up to 50 mJ</td></tr><tr><td>Plano-concave lens</td><td>Thorlabs</td><td>N-BK7</td><td>lens of focus 125 mm</td></tr><tr><td>Spherical concave lens</td><td>Thorlabs</td><td>N-SF11</td><td>Bi-concave lens of focus -25mm</td></tr><tr><td>Ultrasound transducer</td><td>SinapTec</td><td>Custom-made</td><td>Nominal frequency 31kHz, active area 35mm diameter</td></tr><tr><td>Visualization software</td><td>NIH</td><td>ImageJ</td><td>Software for image processing and analysis in Java</td></tr><tr><td>XY Linear stage</td><td>Newport</td><td>M-406</td><td>Displacement stage with micrometric screw</td></tr><tr><td>Z-axis linear stage</td><td>Edmund Optics</td><td>62-299</td><td>Vertical displacement stage with micrometric screw</td></tr></tbody></table>

induction of microstreaming by nonspherical bubble oscillations in an acoustic levitation system

When located near biological barriers, oscillating microbubbles may increase cell membrane permeability, allowing for drug and gene internalization. Experimental observations suggest that the temporary permeabilization of these barriers may be due to shear stress that is exerted on cell tissues by cavitation microstreaming. Cavitation microstreaming is the generation of vortex flows which arise around oscillating ultrasound microbubbles. To produce such liquid flows, bubble oscillations must deviate from purely spherical oscillations and include either a translational instability or shape modes. Experimental studies of bubble-induced flows and shear stress on nearby surfaces are often restricted in their scope due to the difficulty of capturing shape deformations of microbubbles in a stable and controllable manner. We describe the design of an acoustic levitation chamber for the study of symmetry-controlled nonspherical oscillations. Such control is performed by using a coalescence technique between two approaching bubbles in a sufficiently intense ultrasound field. The control of nonspherical oscillations opens the way to a controlled cavitation microstreaming of a free surface-oscillating microbubble. High-frame rate cameras allow investigating quasi-simultaneously the nonspherical bubble dynamics at the acoustic timescale and the liquid flow at a lower timescale. It is shown that a large variety of fluid patterns may be obtained and that they are correlated to the modal content of the bubble interface. We demonstrate that even the high-order shape modes can create large-distance fluid patterns if the interface dynamics contain several modes, highlighting the potential of nonspherical oscillations for targeted and localized drug delivery.

A complete sequence of bubble coalescence leading to time-stable, symmetry-controlled nonspherical oscillations is presented in Figure 9. The approaching phase of two spherically-oscillating bubbles ends when the thin liquid film between the two bubbles is ruptured. It is worth noting that, at the last stage prior to the coalescence, the bubble interfaces deviate from sphericity. Both bubbles elongate on an ellipsoidal shape along the path of the rectilinear ...

Watch this Scientific Journal Video about Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System at JoVE.com

Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System

A fast and reliable technique is proposed to control the shape oscillations of a single, trapped acoustic bubble that is based on coalescence technique between two bubbles. The steady-state, symmetry-controlled bubble shape oscillations allow analysis of the fluid flow generated in the vicinity of the bubble interface.

When located near biological barriers, oscillating microbubbles may increase cell membrane permeability, allowing for drug and gene internalization. ...

induction-microstreaming-nonspherical-bubble-oscillations-an-acoustic

Universidad de Cartagena UDEC

Research

JoVE Journal

Engineering

2.1K Views.  Université Claude Bernard Lyon 1, Centre Léon Bérard, INSERM, UMR 1032, LabTAU, France. A fast and reliable technique is proposed to control the shape oscillations of a single, trapped acoustic bubble that is based on coalescence technique between two bubbles. The steady-state, symmetry-controlled bubble shape oscillations allow analysis of the fluid flow generated in the vicinity of the bubble interface.

Video: Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System

Activating Molecules, Ions, and Solid Particles with Acoustic Cavitation

The chemical and physical effects of ultrasound arise not from a direct interaction of molecules with sound waves, but rather from the acoustic cavitation: the nucleation, growth, and implosive collapse of microbubbles in liquids submitted to power ultrasound. The violent implosion of bubbles leads to the formation of chemically reactive species and to the emission of light, named sonoluminescence. In this manuscript, we describe the techniques allowing study of extreme intrabubble conditions and chemical reactivity of acoustic cavitation in solutions. The analysis of sonoluminescence spectra of water sparged with noble gases provides evidence for nonequilibrium plasma formation. The photons and the "hot" particles generated by cavitation bubbles enable to excite the non-volatile species in solutions increasing their chemical reactivity. For example the mechanism of ultrabright sonoluminescence of uranyl ions in acidic solutions varies with uranium concentration: sonophotoluminescence dominates in diluted solutions, and collisional excitation contributes at higher uranium concentration. Secondary sonochemical products may arise from chemically active species that are formed inside the bubble, but then diffuse into the liquid phase and react with solution precursors to form a variety of products. For instance, the sonochemical reduction of Pt(IV) in pure water provides an innovative synthetic route for monodispersed nanoparticles of metallic platinum without any templates or capping agents. Many studies reveal the advantages of ultrasound to activate the divided solids. In general, the mechanical effects of ultrasound strongly contribute in heterogeneous systems in addition to chemical effects. In particular, the sonolysis of PuO2 powder in pure water yields stable colloids of plutonium due to both effects.

Acoustic cavitation in liquids submitted to power ultrasound creates transient extreme conditions inside the collapsing bubbles, which are the origin of unusual chemical reactivity and light emission, known as sonoluminescence. In the presence of noble gases, nonequilibrium plasma is formed. The "hot" particles and the photons generated by collapsing bubbles are able to excite species in solution.

The chemical and physical effects of ultrasound arise not from a direct interaction of molecules with sound waves, but rather from the acoustic ...

Chemistry

Fabrication, Operation and Flow Visualization in Surface-acoustic-wave-driven Acoustic-counterflow Microfluidics

Surface acoustic waves (SAWs) can be used to drive liquids in portable microfluidic chips via the acoustic counterflow phenomenon. In this video we present the fabrication protocol for a multilayered SAW acoustic counterflow device. The device is fabricated starting from a lithium niobate (LN) substrate onto which two interdigital transducers (IDTs) and appropriate markers are patterned. A polydimethylsiloxane (PDMS) channel cast on an SU8 master mold is finally bonded on the patterned substrate. Following the fabrication procedure, we show the techniques that allow the characterization and operation of the acoustic counterflow device in order to pump fluids through the PDMS channel grid. We finally present the procedure to visualize liquid flow in the channels. The protocol is used to show on-chip fluid pumping under different flow regimes such as laminar flow and more complicated dynamics characterized by vortices and particle accumulation domains.

In this video we first describe fabrication and operation procedures of a surface acoustic wave (SAW) acoustic counterflow device. We then demonstrate an experimental setup that allows for both qualitative flow visualization and quantitative analysis of complex flows within the SAW pumping device.

Surface acoustic waves (SAWs) can be used to drive liquids in portable microfluidic chips via the acoustic counterflow phenomenon. In this video we ...

Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles

Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must be smaller than the incident wavelength of sound and the width of the fluidic channels are typically tens to hundreds of micrometers across, acoustofluidic devices typically use ultrasonic waves generated from a piezoelectric transducer pulsating at high frequencies (in the megahertz range). At characteristic frequencies that depend on the geometry of the device, it is possible to induce the formation of standing waves that can focus particles along desired fluidic streamlines within a bulk flow. Here, we describe a method for the fabrication of acoustophoretic devices from common materials and clean room equipment. We show representative results for the focusing of particles with positive or negative acoustic contrast factors, which move towards the pressure nodes or antinodes of the standing waves, respectively. These devices offer enormous practical utility for precisely positioning large numbers of microscopic entities (e.g., cells) in stationary or flowing fluids for applications ranging from cytometry to assembly.

Acoustofluidic devices use ultrasonic waves within microfluidic channels to manipulate, concentrate and isolate suspended micro and nanoscopic entities. This protocol describes the fabrication and operation of such a device supporting bulk acoustic standing waves to focus particles in a central streamline without the aid of sheath fluids.

Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must ...

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

An analog, macroscopic method for studying molecular-scale hydrodynamic processes in dense gases and liquids is described. The technique applies a standard fluid dynamic diagnostic, particle image velocimetry (PIV), to measure: i) velocities of individual particles (grains), extant on short, grain-collision time-scales, ii) velocities of systems of particles, on both short collision-time- and long, continuum-flow-time-scales, iii) collective hydrodynamic modes known to exist in dense molecular fluids, and iv) short- and long-time-scale velocity autocorrelation functions, central to understanding particle-scale dynamics in strongly interacting, dense fluid systems. The basic system is composed of an imaging system, light source, vibrational sensors, vibrational system with a known media, and PIV and analysis software. Required experimental measurements and an outline of the theoretical tools needed when using the analog technique to study molecular-scale hydrodynamic processes are highlighted. The proposed technique provides a relatively straightforward alternative to photonic and neutron beam scattering methods traditionally used in molecular hydrodynamic studies.

An experimentally accessible analog method for studying molecular hydrodynamic processes in dense fluids is presented. The technique uses particle image velocimetry of vibrated, high-restitution grain piles and allows direct, macroscopic observation of dynamical processes known and predicted to exist in strongly interacting, high density gases and liquids.

An analog, macroscopic method for studying molecular-scale hydrodynamic processes in dense gases and liquids is described. The technique applies a ...

Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations

We demonstrate a method for increasing the tuning ability of a standing surface acoustic wave (SSAW) for microparticles manipulation in a lab-on-a-chip (LOC) system. The simultaneous excitation of the fundamental frequency and its third harmonic, which is termed as dual-frequency excitation, to a pair of interdigital transducers (IDTs) could generate a new type of standing acoustic waves in a microfluidic channel. Varying the power and the phase in the dual-frequency excitation signals results in a reconfigurable field of the acoustic radiation force applied to the microparticles across the microchannel (e.g., the number and location of the pressure nodes and the microparticle concentrations at the corresponding pressure nodes). This article demonstrates that the motion time of the microparticle to only one pressure node can be reduced ~2-fold at the power ratio of the fundamental frequency greater than ~90%. In contrast, there are three pressure nodes in the microchannel if less than this threshold. Furthermore, adjusting the initial phase between the fundamental frequency and the third harmonic results in different motion rates of the three SSAW pressure nodes, as well as in the percentage of microparticles at each pressure node in the microchannel. There is a good agreement between the experimental observation and the numerical predictions. This novel excitation method can easily and non-invasively integrate into the LOC system, with a wide tenability and only a few changes to the experimental set-up.

A protocol for manipulating the microparticles in a microfluidic channel with a dual-frequency excitation is presented.

We demonstrate a method for increasing the tuning ability of a standing surface acoustic wave (SSAW) for microparticles manipulation in a lab-on-a-chip ...

A Microfluidic Platform for Precision Small-volume Sample Processing and Its Use to Size Separate Biological Particles with an Acoustic Microdevice

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. However, to achieve robust sample manipulation it is necessary to address device integration with the macroscale environment. To realize repeatable, sensitive particle separation with microfluidic devices, this protocol presents a complete automated and integrated microfluidic platform that enables precise processing of 0.15&#8211;1.5 ml samples using microfluidic devices. Important aspects of this system include modular device layout and robust fixtures resulting in reliable and flexible world to chip connections, and fully-automated fluid handling which accomplishes closed-loop sample collection, system cleaning and priming steps to ensure repeatable operation. Different microfluidic devices can be used interchangeably with this architecture. Here we incorporate an acoustofluidic device, detail its characterization, performance optimization, and demonstrate its use for size-separation of biological samples. By using real-time feedback during separation experiments, sample collection is optimized to conserve and concentrate sample. Although requiring the integration of multiple pieces of equipment, advantages of this architecture include the ability to process unknown samples with no additional system optimization, ease of device replacement, and precise, robust sample processing.

This protocol describes a system architecture for performing automated small volume (0.15&#8211;1.5 ml) particle separations using a microfluidic device, and discusses methods to optimize acoustofluidic device performance and operation.

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. ...

Bioengineering

Fabrication of Nanoheight Channels Incorporating Surface Acoustic Wave Actuation via Lithium Niobate for Acoustic Nanofluidics

Controlled nanoscale manipulation of fluids is known to be exceptionally difficult due to the dominance of surface and viscous forces. Megahertz-order surface acoustic wave (SAW) devices generate tremendous acceleration on their surface, up to 108 m/s2, in turn responsible for many of the observed effects that have come to define acoustofluidics: acoustic streaming and acoustic radiation forces. These effects have been used for particle, cell, and fluid manipulation at the microscale, although more recently SAW has been used to produce similar phenomena at the nanoscale through an entirely different set of mechanisms. Controllable nanoscale fluid manipulation offers a broad range of opportunities in ultrafast fluid pumping and biomacromolecule dynamics useful for physical and biological applications. Here, we demonstrate nanoscale-height channel fabrication via room-temperature lithium niobate (LN) bonding integrated with a SAW device. We describe the entire experimental process including nano-height channel fabrication via dry etching, plasma-activated bonding on lithium niobate, the appropriate optical setup for subsequent imaging, and SAW actuation. We show representative results for fluid capillary filling and fluid draining in a nanoscale channel induced by SAW. This procedure offers a practical protocol for nanoscale channel fabrication and integration with SAW devices useful to build upon for future nanofluidics applications.

We demonstrate fabrication of nanoheight channels with the integration of surface acoustic wave actuation devices upon lithium niobate for acoustic nanofluidics via liftoff photolithography, nano-depth reactive ion etching, and room-temperature plasma surface-activated multilayer bonding of single-crystal lithium niobate, a process similarly useful for bonding lithium niobate to oxides.

Controlled nanoscale manipulation of fluids is known to be exceptionally difficult due to the dominance of surface and viscous forces. Megahertz-order ...

Fabrication and Characterization of Thickness Mode Piezoelectric Devices for Atomization and Acoustofluidics

We present a technique to fabricate simple thickness mode piezoelectric devices using lithium niobate (LN). Such devices have been shown to atomize liquid more efficiently, in terms of &#64258;ow rate per power input, than those that rely on Rayleigh waves and other modes of vibration in LN or lead zirconate titanate (PZT). The complete device is composed of a transducer, a transducer holder, and a &#64258;uid supply system. The fundamentals of acoustic liquid atomization are not well known, so techniques to characterize the devices and to study the phenomena are also described. Laser Doppler vibrometry (LDV) provides vibration information essential in comparing acoustic transducers and, in this case, indicates whether a device will perform well in thickness vibration. It can also be used to &#64257;nd the resonance frequency of the device, though this information is obtained more quickly via impedance analysis. Continuous &#64258;uid atomization, as an example application, requires careful &#64258;uid flow control, and we present such a method with high-speed imaging and droplet size distribution measurements via laser scattering.

Fabrication of piezoelectric thickness mode transducers via direct current sputtering of plate electrodes on lithium niobate is described. Additionally, reliable operation is achieved with a transducer holder and &#64258;uid supply system and characterization is demonstrated via impedance analysis, laser doppler vibrometry, high-speed imaging, and droplet size distribution using laser scattering.

We present a technique to fabricate simple thickness mode piezoelectric devices using lithium niobate (LN). Such devices have been shown to atomize liquid ...

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels

Microfluidic technology has become a standard tool in chemical and biological laboratories for both analysis and synthesis. The injection of liquid samples, such as chemical reagents and cell cultures, is predominantly accomplished through steady flows that are typically driven by syringe pumps, gravity, or capillary forces. The use of complementary oscillatory flows is seldom considered in applications despite its numerous advantages as recently demonstrated in the literature. The significant technical barrier to the implementation of oscillatory flows in microchannels is likely responsible for the lack of its widespread adoption. Advanced commercial syringe pumps that can produce oscillatory flow, are often more expensive and only work for frequencies less than 1 Hz. Here, the assembly and operation of a low-cost, plug-and-play type speaker-based apparatus that generates oscillatory flow in microchannels is demonstrated. High-fidelity harmonic oscillatory flows with frequencies ranging from 10-1000 Hz can be achieved along with independent amplitude control. Amplitudes ranging from 10-600 &#181;m can be achieved throughout the entire range of operation, including amplitudes &#62; 1 mm at the resonant frequency, in a typical microchannel. Although the oscillation frequency is determined by the speaker, we illustrate that the oscillation amplitude is sensitive to fluid properties and channel geometry. Specifically, the oscillation amplitude decreases with increasing channel circuit length and liquid viscosity, and in contrast, the amplitude increases with increasing speaker tube thickness and length. Additionally, the apparatus requires no prior features to be designed on the microchannel and is easily detachable. It can be used simultaneously with a steady flow created by a syringe pump to generate pulsatile flows.

The protocol demonstrates a convenient method to produce harmonic oscillatory flow from 10-1000 Hz in microchannels. This is performed by interfacing a computer-controlled speaker diaphragm to the microchannel in a modular manner.

Microfluidic technology has become a standard tool in chemical and biological laboratories for both analysis and synthesis. The injection of liquid ...

Studying Cavitation Enhanced Therapy

Interest in the therapeutic applications of ultrasound is significant and growing, with potential clinical targets ranging from cancer to Alzheimer&#8217;s disease. Cavitation - the formation and subsequent motion of bubbles within an ultrasound field - represents a key phenomenon underpinning many of these treatments. There remains, however, considerable uncertainty regarding the detailed mechanisms of action by which cavitation promotes therapeutic effects and there is a need to develop reliable monitoring techniques that can be implemented clinically. In particular, there is significant variation between studies in the exposure parameters reported as successfully delivering therapeutic effects and the corresponding acoustic emissions. The aim of this paper is to provide design guidelines and an experimental protocol using widely available components for performing studies of cavitation-mediated bioeffects, and&#160;include real-time acoustic monitoring. It is hoped that the protocol will enable more widespread incorporation of acoustic monitoring into therapeutic ultrasound experiments and facilitate easier comparison across studies of exposure conditions and their correlation to relevant bio-effects.

The presented experimental protocol can be used to perform real time measurements of cavitation activity in a cell culture device with the aim of enabling investigation of the conditions required for successful drug delivery and/or other bioeffects.