This project was supported by Chang Gung Medical Foundation with grant BMRP390021 and the Ministry of Science and Technology with grants MOST 107-2218-E-182A-001 and 108-2218-E-182A-001.

The training protocol and informed consent document were reviewed and approved by the Institutional Review Board of the Chang Gung Medical Foundation. The details of the study and the procedures were clearly explained to each subject.
1. Recruitment of three healthy adults
<ol>
	<li>Perform the screening process using the following inclusion criteria: (1) age 20&#8211;60 years, (2) already signed informed consent, (3) normal function in upper limbs, (4) Mini-Mental State Examination (MMSE) score &#8807;24.</li>
	<li>Conduct Trial 1: manipulating objects without wearing the robotic hand system.
	<ol>
		<li>Instruct the subject to sit upright in a chair with a firm back and no armrests. Seat the subject in front of a table. Stand by the subject&#8217;s non-dominant side.</li>
		<li>Teach the subject how to manipulate the designed objects for 5 min. Include a palmar prehension to pick up the peg, a lateral prehension to pick up the rectangular cube, a three-point chuck to pick up the cube, a spherical grasp to pick up the ball, and a cylindrical grasp to pick up the cylindrical bar. 
		NOTE: The objects are shown in Figure 1A. The experimental setup is shown in Figure 1B. The subjects learned the specific grasp patterns for each object. The grasping pattern is shown in Figure 2.</li>
		<li>Place two bases bilaterally in front of the subject&#8217;s hands. Place each object used in the rehabilitation on top of these bases to assist manipulation. For all the objects, repeat the following sequences 20 times. Ask the subjects to grasp the objects in the starting area of the base, lift, and move them to the midline and release using their non-dominant hands.</li>
		<li>At the same time, measure the success rate for these 20 attempts. Perform this procedure on 3 consecutive days. The success rate is the number of successful manipulations per 20 attempts x 100%. Successful manipulation is defined as when the subjects are able to complete the sequences with specific grasp pattern according to the objects and without dropping them.</li>
	</ol>
	</li>
	<li>Conduct Trial 2: manipulating objects using robotic hand system (Figure 3). 
	NOTE: The mechanisms of the robotic hand system are as follows. In the exoskeleton hand, the joints in each finger module are designed in mechanical linking and driven by an individual linear actuator with a constant speed of 10 mm/s. The exoskeleton has different ranges of motion in each finger module (thumb: MCP= 0&#176; to 55&#176;, DIP= 0&#176; to 70&#176;; index and middle fingers: MCP= -10 &#176; to 55&#176;, PIP=0&#176; to 35&#176;, DIP=0&#176; to 35&#176;; ring and little fingers: MCP= -5 &#176; to 55&#176;, PIP= 0&#176; to 35&#176;, DIP= 0&#176; to 35&#176;). In the sensor glove, each finger module is installed with a flex sensor which measures the joint angle and sends input signals to the control box through cables.
	<ol>
		<li>Sensor glove setup (Figure 1B,b)
		<ol>
			<li>Put the sensor glove&#160;on the subject&#8217;s dominant hand. Use the Velcro to secure the wrist.</li>
		</ol>
		</li>
		<li>Exoskeleton setup (Figure 1B,b)
		<ol>
			<li>Use a clean pad to wrap the non-dominant hand. Fasten the Velcro snugly.</li>
			<li>Loosen the thumb mechanism of the exoskeleton hand to allow adjustment of the thumb-opening angle. Place the non-dominant hand in the exoskeleton hand. Fasten the Velcro to the palm through the fastening ring. Fasten the fingers one by one, beginning with the forefinger and finishing with the thumb.</li>
			<li>Then, fasten the Velcro parallel to the wrist through the fastening ring. Adjust the thumb to a comfortable angle and then tighten the thumb mechanism.</li>
		</ol>
		</li>
		<li>Control box setup (Figure 1A,c)
		<ol>
			<li>Insert the cables for the exoskeleton&#160;hand and sensor glove into the sockets in the exoskeleton&#160;hand and sensor glove, respectively. After that, insert the cables for the exoskeleton&#160;hand and sensor glove into the socket in the control box. Finally, insert the power cable into the control box and connect it to an outlet with the correct voltage.</li>
		</ol>
		</li>
		<li>Conduct a warm-up session (The PROM mode)
		<ol>
			<li>Switch on the control box and adjust the mode to Five Fingers. This mode allows the exoskeleton hand to move the subject&#8217;s fingers passively. Ask the subject to perform a grasp-and-release task guided by the exoskeleton hand for 2.5 min.</li>
			<li>Switch the mode to Single Finger and let the exoskeleton&#160;hand move the subject&#8217;s fingers individually and passively. Ask the subject to extend and retract individual fingers for 2.5 min, guided by the exoskeleton&#160;hand.</li>
		</ol>
		</li>
		<li>Conduct a robot-assisted bimanual movement session.
		<ol>
			<li>Switch the mode to Mirror. In this mode, the movement of the dominant hand wearing the sensor glove controls the exoskeleton hand&#8217;s movements. Any movement that is made by the sensor glove is mimicked and mirrored by the exoskeleton&#160;hand. For example, a flexion of the sensor glove&#8217;s index finger corresponds to a flexion of the exoskeleton&#8217;s index finger.</li>
		</ol>
		</li>
		<li>Instruct the subject to perform a grasp-and-release task for 2.5 min and make individual finger movements for a further 2.5 min while wearing the sensor glove. This action is mirrored by the exoskeleton hand, which guides the subject&#8217;s non-dominant hand in performing the required tasks.</li>
	</ol>
	</li>
	<li>Conduct the task-oriented session.
	<ol>
		<li>Teach the subject how to manipulate the designed objects using the robotic hand system for 5 min. Include a palmar prehension to pick up the peg, a lateral prehension to pick up the rectangular cube, a three-point chuck to pick up the cube, a spherical grasp to pick up the ball, and a cylindrical grasp to pick up the cylindrical bar.</li>
		<li>Place two bases bilaterally in front of the subject&#8217;s hands. Place each object used in the rehabilitation on top of these bases to assist manipulation. For all the objects, repeat the following sequences 20 times. Ask the subjects to grasp the object in the starting area of the base, lift, and move them to the midline and release using the robotic hand system.</li>
		<li>At the same time, measure the success rate for these 20 attempts. Perform this procedure on 3 consecutive days. The success rate is the number of successful manipulations per 20 attempts x 100%. Successful manipulation is defined as when the subjects are able to complete the sequences with specific grasp pattern using the robotic hand system and without dropping them. 
		NOTE: The success rate will be used to assess the feasibility of the bimanual robotic hand system in healthy subjects.</li>
	</ol>
	</li>
</ol>
2. Recruit three stroke patients to determine the applicability of the training program
<ol>
	<li>Perform the screening process using the following inclusion criteria: (1) age 20&#8211;60 years; (2) signed informed consent; (3) diagnosed with unilateral stroke &#8807; 1 month (4) Modified Ashworth Scale (MAS) score &#8806;2; (5) Brunnstrom stage &#8806;2; (6) MMSE score &#8807;24.</li>
	<li>Conduct Trial 1: manipulating objects when not using robotic hand system (Figure 2).
	<ol>
		<li>Let the subject sit upright in a chair with a firm back and no armrests. Seat the subject in front of a table. Stand by the subject&#8217;s affected side. Place a sling under the subject&#8217;s elbow and exoskeleton hand to support his/her affected arm.</li>
		<li>Teach the subject how to manipulate the designed objects for 5 min. Include a palmar prehension to pick up the peg, a lateral prehension to pick up the rectangular cube, a three-point chuck to pick up the cube, a spherical grasp to pick up the ball, and a cylindrical grasp to pick up the cylindrical bar.</li>
		<li>Place two bases bilaterally in front of the subject&#8217;s hands. Place each object used in the rehabilitation on top of these bases to assist manipulation. Ask the subject to manipulate the five different objects using his/her affected hand 20 times. Support the subject in moving his/her upper arm if needed.</li>
		<li>At the same time, measure the success rate for these 20 attempts. Perform this procedure on 3 consecutive days.</li>
	</ol>
	</li>
	<li>Conduct Trial 2: manipulating objects using robotic hand system (Figure 3).
	<ol>
		<li>Fit the exoskeleton hand to the subject&#8217;s affected hand and the sensor glove to the unaffected hand. Repeat steps 1.3.1&#8211;1.3.3. Place a sling under the subject&#8217;s elbow and exoskeleton hand to support his/her affected arm.</li>
		<li>Conduct a warm-up session (The PROM mode).
		<ol>
			<li>Switch on the control box and adjust the mode to Five Fingers. Ask the subject to perform a grasp-and-release task guided by the exoskeleton hand for 2.5 min.</li>
			<li>Switch the mode to Single Finger. Ask the subject to extend and retract individual fingers for 2.5 min, guided by the exoskeleton hand.</li>
			<li>Switch the mode to Mirror. Instruct the subject to perform a grasp-and-release task for 2.5 min and make individual finger movements for a further 2.5 min while wearing the sensor glove. This action is mirrored by the exoskeleton hand, which guides the subject&#8217;s affected hand in performing the required tasks.</li>
		</ol>
		</li>
		<li>Conduct a task-oriented session.</li>
		<li>Teach the subject how to manipulate the designed objects using the robotic hand system for 5 min. Include a palmar prehension to pick up the peg, a lateral prehension to pick up the rectangular cube, a three-point chuck to pick up the cube, a spherical grasp to pick up the ball, and a cylindrical grasp to pick up the cylindrical bar.</li>
		<li>Place two bases bilaterally in front of the subject&#8217;s hands. Place each object used in the rehabilitation on top of these bases to assist manipulation. For all the objects, repeat the following sequences 20 times. Ask the subjects to grasp the objects in the starting area of the base, lift, and move them to the midline and release using the robotic hand system.</li>
		<li>At the same time, measure the success rate for these 20 attempts. Perform this procedure on 3 consecutive days. The success rate is the number of successful manipulations per 20 attempts x 100%. Successful manipulation is defined as when the subjects are able to complete the sequences with specific grasp pattern using the robotic hand system and without dropping them. 
		NOTE: The success rate will be used to assess the feasibility of the robotic hand system in stroke patients.</li>
	</ol>
	</li>
</ol>
3. Patient evaluation
<ol>
	<li>To assess acceptability, ask the subjects following questions at the end of each session: (1) was the robotic hand system helpful for you to manipulate the objects? (2) were there any adverse events happened during or after the training program?</li>
</ol>

<ol>
	<li>Hung, C. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+effects+of+combination+of+robot-assisted+therapy+with+task-specific+or+impairment-oriented+training+on+motor+function+and+quality+of+life+in+chronic+stroke.">The effects of combination of robot-assisted therapy with task-specific or impairment-oriented training on motor function and quality of life in chronic stroke.</a> PM &amp; R: The Journal of Injury, Function, and Rehabilitation. 8 (8), 721-729 (2016).</li><li>SangWook, L., Landers, K. A., Hyung-Soon, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+a+biomimetic+hand+exotendon+device+(BiomHED)+for+restoration+of+functional+hand+movement+post-stroke.">Development of a biomimetic hand exotendon device (BiomHED) for restoration of functional hand movement post-stroke.</a> IEEE Transactions on Neural Systems and Rehabilitation Engineering. 22 (4), 886-898 (2014).</li><li>Johnson, M. J., Wisneski, K. J., Anderson, J., Nathan, D., Smith, R. O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+ADLER:+The+Activities+of+Daily+Living+Exercise+Robot.">Development of ADLER: The Activities of Daily Living Exercise Robot.</a> Proceedings of IEEE/RAS-EMBS International Conference. , (2006).</li><li>Pignolo, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Robotics+in+neuro-rehabilitation.">Robotics in neuro-rehabilitation.</a> Journal of Rehabilitation Medicine. 41 (12), 955-960 (2009).</li><li>Timmermans, A. A., Spooren, A. I., Kingma, H., Seelen, H. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Influence+of+task-oriented+training+content+on+skilled+arm-hand+performance+in+stroke:+a+systematic+review.">Influence of task-oriented training content on skilled arm-hand performance in stroke: a systematic review.</a> Neurorehabilitation and Neural Repair. 24 (9), 858-870 (2010).</li><li>Schweighofer, N., Choi, Y., Winstein, C., Gordon, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Task-oriented+rehabilitation+robotics.">Task-oriented rehabilitation robotics.</a> American Journal of Physical Medicine &amp; Rehabilitation. 91, 270-279 (2012).</li><li>Almhdawi, K. A., Mathiowetz, V. G., White, M., delMas, R. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Efficacy+of+occupational+therapy+task-oriented+approach+in+upper+extremity+post-stroke+rehabilitation.">Efficacy of occupational therapy task-oriented approach in upper extremity post-stroke rehabilitation.</a> Occupational Therapy International. 23 (4), 444-456 (2016).</li><li>Takahashi, C. D., Der-Yeghiaian, L., Le, V. H., Cramer, S. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+robotic+device+for+hand+motor+therapy+after+stroke.">A robotic device for hand motor therapy after stroke.</a> Proceedings of 9th International Conference on Rehabilitation Robotics. , (2005).</li><li>Villafa&#241;e, J. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Efficacy+of+short-term+robot-assisted+rehabilitation+in+patients+with+hand+paralysis+after+stroke:+a+randomized+clinical+trial.">Efficacy of short-term robot-assisted rehabilitation in patients with hand paralysis after stroke: a randomized clinical trial.</a> Hand (NY). 13 (1), 95-102 (2018).</li><li>Cauraugh, J. H., Lodha, N., Naik, S. K., Summers, J. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bilateral+movement+training+and+stroke+motor+recovery+progress:+a+structured+review+and+meta-analysis.">Bilateral movement training and stroke motor recovery progress: a structured review and meta-analysis.</a> Human Movement Science. 29 (5), 853-870 (2010).</li><li>Brunner, I. C., Skouen, J. S., Strand, L. I. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Is+modified+constraint-induced+movement+therapy+more+effective+than+bimanual+training+in+improving+arm+motor+function+in+the+subacute+phase+post+stroke?+A+randomized+controlled+trial.">Is modified constraint-induced movement therapy more effective than bimanual training in improving arm motor function in the subacute phase post stroke? A randomized controlled trial.</a> Clinical Rehabilitation. 26 (12), 1078-1086 (2012).</li><li>Sleimen-Malkoun, R., Temprado, J. J., Thefenne, L., Berton, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bimanual+training+in+stroke:+how+do+coupling+and+symmetry-breaking+matter.">Bimanual training in stroke: how do coupling and symmetry-breaking matter.</a> BMC Neurology. 11, 11 (2011).</li><li>Yue, Z., Zhang, X., Wang, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hand+rehabilitation+robotics+on+poststroke+motor+recovery.">Hand rehabilitation robotics on poststroke motor recovery.</a> Behavioural Neurology. 2017, 1-20 (2017).</li><li>Dovat, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=HandCARE:+a+cable-actuated+rehabilitation+system+to+train+hand+function+after+stroke.">HandCARE: a cable-actuated rehabilitation system to train hand function after stroke.</a> IEEE Transactions on Neural Systems and Rehabilitation Engineering. 16 (6), 582-591 (2008).</li><li>Yoo, C., Park, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Impact+of+task-oriented+training+on+hand+function+and+activities+of+daily+living+after+stroke.">Impact of task-oriented training on hand function and activities of daily living after stroke.</a> Journal of Physical Therapy Science. 27 (8), 2529-2531 (2015).</li></ol>

The authors declare no conflict of interest.

The results of this study showed the following: (1) both groups could successfully grasp the objects provided with the robotic hand system. They were able to complete this task with a nearly 100% success rate, which verifies the feasibility of the proposed robot-assisted task-oriented training program. (2) There were no reports of injury or adverse events during the study period and all patients reported that the robotic hand system was helpful to manipulate objects. This confirmed the acceptability of the robotic hand s...

Most (80%) stroke patients experience a deficit in the hand and have difficulty in independently performing manual tasks that are pertinent to daily living1. However, the complex nature of manual tasks means that it is a significant challenge to design a task-oriented training program for hand rehabilitation2. In recent years, many robotic devices have been developed for hand rehabilitation3,4, but few training protocols assisted by robotic devices allow a patient to interact with real objects. It is unclear exactly how a task-oriented training program for hand function rehabilitation can be applied using robotic devices for patients who experience hand dysfunction due to stroke.
Task-oriented training is used to improve hand function5,6 and is commonly applied in the rehabilitation for upper limb dysfunction due to stroke. It is used to increase neuroplasticity and is highly dependent on individual neurological deficits and functional demands7. However, during task-oriented training, patients experience difficultly in manipulating objects if hand function is impaired. Examples of this include poor grasp or limited pinch functions. Therapists also show difficulty in guiding patients&#8217; finger movements individually, which therefore limits the variation of grasping tasks. Robotic devices are thus necessary to increase the effectiveness of task-oriented training by explicitly guiding hand movement during repetitive training2,8.
Previous studies only used rehabilitation robots for task-oriented training on upper-limb reaching tasks3. It is unclear how robot-assisted rehabilitation can be employed for task-oriented training targeting at hand function. An exoskeleton&#160;hand, HWARD, has been used to guide the fingers to grasp and release objects8. However, this device does not allow varied grasping patterns because it lacks the necessary degrees of freedom. Recently, other devices that target moving a patient&#8217;s fingers individually have been developed9. However, these devices have not previously been used for neurorehabilitation. The robotic devices mentioned above are all unilateral robots. In contrast, the robotic hand system presented here needs the cooperation of unaffected and affected hands. The robotic hand system is specifically designed for rehabilitation purposes using the master&#8211;slave mechanism to achieve symmetric bimanual hand movements. The system consists of an exoskeleton hand (worn on the affected hand), a control box, and a sensory glove (worn on the unaffected hand). Each finger module of the exoskeleton hand is driven by a motor with one degree of freedom and its joints are linked using a mechanical linkage system. Two sizes, S and M, are designed to fit different subjects. The control box provides two therapeutic modes, the passive range of motion (PROM) and mirror-guided motion modes, through which the patient&#8217;s affected hand can be manipulated by the exoskeleton hand. In the PROM mode, the control box sends input commands to the exoskeleton while moves the subject&#8217;s hand to perform full finger flexion/extension. It contains two modes: single-finger mode (acts in sequence from thumb to little finger) and five fingers mode (five fingers move together). In the mirror-guided motion mode, the master (sensor glove)&#8211;slave (exoskeleton hand) mechanism is implemented, in which the movement of each finger is detected by the sensor glove and signals of the joint angles are transmitted to the control box to manipulate the exoskeleton hand.
When equipped the robotic hand system, the subjects were instructed to move their affected hands under the guidance of the exoskeleton hand controlled by unaffected hands which is bimanual movement training (BMT)10. According to previous research, BMT is able to activate similar neural pathways in both hemispheres of the brain and prevent the trans-hemisphere inhibition that hinders the recovery of neuronal function in the lesion hemisphere10. Brunner et al.11 compared BMT to constraint-induced movement therapy (CIMT) in sub-acute stroke patients. They suggested that BMT tends to activate more neural networks in both hemispheres than CIMT, and there was no significant difference in improvement of hand function between the BMT and CIMT approaches. Sleimen-Malkoun et al.12 also suggested that through BMT, stroke patients are able to re-establish both paretic limb control and bimanual control. That is to say, training should comprise bimanual tasks that focus on using the affected arm. Moreover, the coordination of both hands is necessary for activities of daily living (ADL)11,12. Therefore, it is crucial to develop a bimanual robot-assisted task-oriented training program for post-stroke patients and objects that can be grasped or pinched by patients wearing the robotic hand system.
In this study, a variety of grasping objects were designed based on the needs of occupational therapy and the mechanical properties of rehabilitation robots. A task-oriented training protocol was developed using robotic rehabilitation devices for patients with distal upper limb dysfunction due to stroke. The purpose of this study was to investigate the feasibility, and acceptability of the task-oriented training program using an exoskeleton robot and newly designed grasping objects.

<table>
	<tbody>
		<tr>
			<td>Control Box</td>
			<td>Rehabotics Medical Technology Corporation</td>
			<td>HB01</td>
			<td>The control box includes a power supply, sensor glove signal receiver, motor signal transmitter, and exoskeletal hand motion mode selection unit.</td>
		</tr>
		<tr>
			<td>Exoskeletal Hand</td>
			<td>Rehabotics Medical Technology Corporation</td>
			<td>HS01</td>
			<td>It is a wearable device causing the patient&#39;s fingers to move and is driven by an external motor and mechanical assembly.</td>
		</tr>
		<tr>
			<td>Sensor Glove</td>
			<td>Rehabotics Medical Technology Corporation</td>
			<td>HM01</td>
			<td>Worn on the patient&#39;s unaffected side hand. The sensors in the sensor glove will detect flexing and extension of the hand, and this data will be used to control the exoskeletal hand when in bimanual mode.</td>
		</tr>
	</tbody>
</table>

development of a novel task-oriented rehabilitation program using a bimanual exoskeleton robotic hand

A robot-assisted hand is used for the rehabilitation of patients with impaired upper limb function, particularly for stroke patients with a loss of motor control. However, it is unclear how conventional occupational training strategies can be applied to the use of rehabilitation robots. Novel robotic technologies and occupational therapy concepts are used to develop a protocol that allows patients with impaired upper limb function to grasp objects using their affected hand through a variety of pinching and grasping functions. To conduct this appropriately, we used five types of objects: a peg, a rectangular cube, a cube, a ball, and a cylindrical bar. We also equipped the patients with a robotic hand, the Mirror Hand, an exoskeleton&#160;hand that is fitted to the subject&#8217;s affected hand and follows the movement of the sensor glove fitted to their unaffected hand (bimanual movement training (BMT)). This study had two stages. Three healthy subjects were first recruited to test the feasibility and acceptability of the training program. Three patients with hand dysfunction caused by stroke were then recruited to confirm the feasibility and acceptability of the training program, which was conducted on 3 consecutive days. On each day, the patient was monitored during 5 min of movement in a passive range of motion, 5 min of robot-assisted bimanual movement, and task-oriented training using the five objects. The results showed that both healthy subjects and subjects who had suffered a stroke in conjunction with the robotic hand could successfully grasp the objects. Both healthy subjects and those who had suffered a stroke performed well with the robot-assisted task-oriented training program in terms of feasibility and acceptability.

A total of six subjects were enrolled in this study, including three healthy subjects and three post-stroke subjects. The demographic data of both groups are shown in Supplementary Table 1. The average age of the healthy group was 28 (range: 24&#8211;30), whereas the average age of the patient group was 49 (40&#8211;57). The average assessment scores of the patient group were as follows: (1) MMSE=27 (26&#8211;29), (2) FMA=11.3 (6&#8211;15), (3) MAS=1, (4) Brunnstrom stage=2.
I...

Watch this Scientific Journal Video about Development of a Novel Task-oriented Rehabilitation Program using a Bimanual Exoskeleton Robotic Hand at JoVE.com

Development of a Novel Task-oriented Rehabilitation Program using a Bimanual Exoskeleton Robotic Hand

This study reports the development of a novel robot-assisted task-oriented program for hand rehabilitation. The developmental process consists of experiments using both healthy subjects and subjects who have had a stroke and suffered from subsequent motor control dysfunction.

A robot-assisted hand is used for the rehabilitation of patients with impaired upper limb function, particularly for stroke patients with a loss of motor ...

development-novel-task-oriented-rehabilitation-program-using-bimanual

Universidad de Cartagena UDEC

Research

JoVE Journal

Medicine

6.9K Views.  Chang Gung Memorial Hospital at Taoyuan. This study reports the development of a novel robot-assisted task-oriented program for hand rehabilitation. The developmental process consists of experiments using both healthy subjects and subjects who have had a stroke and suffered from subsequent motor control dysfunction.

Video: Development of a Novel Task-oriented Rehabilitation Program using a Bimanual Exoskeleton Robotic Hand

A Novel Technique of Rescuing Capsulorhexis Radial Tear-out using a Cystotome

Part 1 : Purpose: To demonstrate a capsulorhexis radial tear out rescue technique using a cystotome on a virtual reality cataract surgery simulator and in a human eye. Part 2 : Method: Steps: When a capsulorhexis begins to veer radially towards the periphery beyond the pupillary margin the following steps should be applied without delay. 2.1) Stop further capsulorhexis manoeuvre and reassess the situation. 2.2) Fill the anterior chamber with ophthalmic viscosurgical device (OVD). We recommend mounting the cystotome to a syringe containing OVD so that the anterior chamber can be reinflated rapidly. 2.3) The capsulorhexis flap is then left unfolded on the lens surface. 2.4) The cystotome tip is tilted horizontally to avoid cutting or puncturing the flap and is engaged on the flap near the leading edge of the tear but not too close to the point of tear. 2.5) Gently push or pull the leading edge of tear opposite to the direction of tear. 2.6) The leading tearing edge will start to do a 'U-Turn'. Maintain the tension on the flap until the tearing edge returns to the desired trajectory. Part 3 : Results: Using our technique, a surgeon can respond instantly to radial tear out without having to change surgical instruments. Changing surgical instruments at this critical stage runs a risk of further radial tear due to sudden shallowing of anterior chamber as a result of forward pressure from the vitreous. Our technique also has the advantage of reducing corneal wound distortion and subsequent anterior chamber collapse. Part 4 : Discussion The EYESI Surgical Simulator is a realistic training platform for surgeons to practice complex capsulorhexis tear-out techniques. Capsulorhexis is the most important and complex part of phacoemulsification and endocapsular intraocular lens implantation procedure. A successful cataract surgery depends on achieving a good capsulorhexis. During capsulorhexis, surgeons may face a challenging situation like a capsulorhexis radial tear-out. A surgeon must learn to tackle the problem promptly without making the situation worse. Some other methods of rescuing the situation have been described using a capsulorhexis forceps. However, we believe our method is quicker, more effective and easier to manipulate as demonstrated on the EYESi surgical simulator and on a human eye. Acknowledgments: List acknowledgements and funding sources. We would like to thank Dr. Wael El Gendy, for video clip. Disclosures: describe potential conflicting interests or state We have nothing to disclose. References: 1. Brian C. Little, Jennifer H. Smith, Mark Packer. J Cataract Refract Surg 2006; 32:1420 1422, Issue-9. 2. Neuhann T. Theorie und Operationstechnik der Kapsulorhexis. Klin Monatsbl Augenheilkd. 1987; 1990: 542-545. 3. Gimbel HV, Neuhann T. Development, advantages and methods of the continuous circular capsulorhexis technique. J Cataract Refract Surg. 1990; 16: 31-37. 4. Gimbel HV, Neuhann T. Continuous curvilinear capsulorhexis. (letter) J Cataract Refract Sur. 1991; 17: 110-111.

Capsulorhexis is an important step in phacoemulsification surgery. A surgeon creates a continous curvilinear tear on the anterior lens capsule by controlling the tearing vector forces. A peripherally extended tear is a serious complication. This video demonstrates a novel technique of rescuing capsular radial tear out using a cystotome.

Part 1 : Purpose:   To demonstrate a capsulorhexis radial tear out rescue technique using a cystotome on a virtual reality cataract surgery simulator and ...

Manual Muscle Testing:  A Method of Measuring Extremity Muscle Strength Applied to Critically Ill Patients

Survivors of acute respiratory distress syndrome (ARDS) and other causes of critical illness often have generalized weakness, reduced exercise tolerance, and persistent nerve and muscle impairments after hospital discharge.1-6 Using an explicit protocol with a structured approach to training and quality assurance of research staff, manual muscle testing (MMT) is a highly reliable method for assessing strength, using a standardized clinical examination, for patients following ARDS, and can be completed with mechanically ventilated patients who can tolerate sitting upright in bed and are able to follow two-step commands. 7, 8 
This video demonstrates a protocol for MMT, which has been taught to &ge;43 research staff who have performed &gt;800 assessments on &gt;280 ARDS survivors. Modifications for the bedridden patient are included. Each muscle is tested with specific techniques for positioning, stabilization, resistance, and palpation for each score of the 6-point ordinal Medical Research Council scale.7,9-11 Three upper and three lower extremity muscles are graded in this protocol: shoulder abduction, elbow flexion, wrist extension, hip flexion, knee extension, and ankle dorsiflexion. These muscles were chosen based on the standard approach for evaluating patients for ICU-acquired weakness used in prior publications. 1,2.

Survivors of acute respiratory distress syndrome (ARDS) and critical illness frequently develop long-lasting muscle weakness. Manual muscle testing (MMT) is a standardized clinical examination commonly used to measure strength of peripheral skeletal muscle groups. This video demonstrates MMT using the 6-point Medical Research Council scale.

Survivors of acute respiratory distress syndrome (ARDS) and other causes of critical illness often have generalized weakness, reduced exercise tolerance, ...

Method for Novel Anti-Cancer Drug Development using Tumor Explants of Surgical Specimens

The current therapies for malignant glioma have only palliative effect. For therapeutic development, one hurdle is the discrepancy of efficacy determined by current drug efficacy tests and the efficacy on patients. Thus, novel and reliable methods for evaluating drug efficacy are warranted in pre-clinical phase. In vitro culture of tumor tissues, including cell lines, has substantial phenotypic, genetic, and epigenetic alterations of cancer cells caused by artificial environment of cell culture, which may not reflect the biology of original tumors in situ. Xenograft models with the immunodeficient mice also have limitations, i.e., the lack of immune system and interspecies genetic and epigenetic discrepancies in microenvironment. Here, we demonstrate a novel method using the surgical specimens of malignant glioma as undissociated tumor blocks to evaluate treatment effects. To validate this method, data with the current first-line chemotherapeutic agent, temozolomide (TMZ), are described.


We used the freshly-removed surgical specimen of malignant glioma for our experiments. We performed intratumoral injection of TMZ or other drug candidates, followed by incubation and analysis on surgical specimens. Here, we sought to establish a tumor tissue explant method as a platform to determine the efficacy of novel anti-cancer therapies so that we may be able to overcome, at least, some of the current limitations and fill the existing gap between the current experimental data and the efficacy on an actual patient's tumor. This method may have the potential to accelerate identifying novel chemotherapeutic agents for solid cancer treatment.

Here, we established a method for drug efficacy testing with surgical specimens of brain tumors, termed &#x201C;tumor explant method&#x201D;. With this method, we can evaluate drug efficacy without breaking the microenvironment of solid tumors. To validate reliability of this method, we describe representative data with our glioma specimen treated with the current first-line chemotherapeutic agent, temozolomide.


The current therapies for malignant glioma have only palliative effect. For therapeutic development, one hurdle is the discrepancy of efficacy determined ...

Using Continuous Data Tracking Technology to Study Exercise Adherence in Pulmonary Rehabilitation

Pulmonary rehabilitation (PR) is an important component in the management of respiratory diseases. The effectiveness of PR is dependent upon adherence to exercise training recommendations. The study of exercise adherence is thus a key step towards the optimization of PR programs. To date, mostly indirect measures, such as rates of participation, completion, and attendance, have been used to determine adherence to PR. The purpose of the present protocol is to describe how continuous data tracking technology can be used to measure adherence to a prescribed aerobic training intensity on a second-by-second basis.
In our investigations, adherence has been defined as the percent time spent within a specified target heart rate range. As such, using a combination of hardware and software, heart rate is measured, tracked, and recorded during cycling second-by-second for each participant, for each exercise session. Using statistical software, the data is subsequently extracted and analyzed. The same protocol can be applied to determine adherence to other measures of exercise intensity, such as time spent at a specified wattage, level, or speed on the cycle ergometer. Furthermore, the hardware and software is also available to measure adherence to other modes of training, such as the treadmill, elliptical, stepper, and arm ergometer. The present protocol, therefore, has a vast applicability to directly measure adherence to aerobic exercise.

Pulmonary rehabilitation is widely recognized in the management of respiratory diseases. A key component to successful pulmonary rehabilitation is adherence to the recommended exercise training. The purpose of the present protocol is to describe how continuous data tracking technology can be used to precisely measure adherence to a prescribed aerobic training intensity.

Pulmonary rehabilitation (PR) is an important component in the management of respiratory diseases. The effectiveness of PR is dependent upon adherence to ...

Ischemic Tissue Injury in the Dorsal Skinfold Chamber of the Mouse: A Skin Flap Model to Investigate Acute Persistent Ischemia

Despite profound expertise and advanced surgical techniques, ischemia-induced complications ranging from wound breakdown to extensive tissue necrosis are still occurring, particularly in reconstructive flap surgery. Multiple experimental flap models have been developed to analyze underlying causes and mechanisms and to investigate treatment strategies to prevent ischemic complications. The limiting factor of most models is the lacking possibility to directly and repetitively visualize microvascular architecture and hemodynamics. The goal of the protocol was to present a well-established mouse model affiliating these before mentioned lacking elements. Harder et al. have developed a model of a musculocutaneous flap with a random perfusion pattern that undergoes acute persistent ischemia and results in ~50% necrosis after 10 days if kept untreated. With the aid of intravital epi-fluorescence microscopy, this chamber model allows repetitive visualization of morphology and hemodynamics in different regions of interest over time. Associated processes such as apoptosis, inflammation, microvascular leakage and angiogenesis can be investigated and correlated to immunohistochemical and molecular protein assays. To date, the model has proven feasibility and reproducibility in several published experimental studies investigating the effect of pre-, peri- and postconditioning of ischemically challenged tissue.

The window of the murine dorsal skinfold chamber presented visualizes a zone of acute persistent ischemia of a musculocutaneous flap. Intravital epi-fluorescence microscopy permits for direct and repetitive assessment of the microvasculature and quantification of hemodynamics. Morphologic and hemodynamic results can further be correlated with histological and molecular analyses.

Despite profound expertise and advanced surgical techniques, ischemia-induced complications ranging from wound breakdown to extensive tissue necrosis are ...

Development of an Algorithm to Perform a Comprehensive Study of Autonomic Dysreflexia in Animals with High Spinal Cord Injury Using a Telemetry Device

Spinal cord injury (SCI) is a debilitating neurological condition characterized by somatic and autonomic dysfunctions. In particular, SCI above the mid-thoracic level can lead to a potentially life-threatening hypertensive condition called autonomic dysreflexia (AD) that is often triggered by noxious or non-noxious somatic or visceral stimuli below the level of injury. One of the most common triggers of AD is the distension of pelvic viscera, such as during bladder and bowel distension or evacuation. This protocol presents a novel pattern recognition algorithm developed for a JAVA platform software to study the fluctuations of cardiovascular parameters as well as the number, severity and duration of spontaneously occurring AD events. The software is able to apply a pattern recognition algorithm on hemodynamic data such as systolic blood pressure (SBP) and heart rate (HR) extracted from telemetry recordings of conscious and unrestrained animals before and after thoracic (T3) complete transection. With this software, hemodynamic parameters and episodes of AD are able to be detected and analyzed with minimal experimenter bias.

The catheter of a telemetry device is implanted into the abdominal aorta in order to continuously collect beat-by-beat hemodynamic data from animals pre and post-high thoracic spinal cord transection. A novel JAVA software was employed to analyze hemodynamic parameters as well as frequency and intensity of spontaneous episodes of autonomic dysreflexia.

Spinal cord injury (SCI) is a debilitating neurological condition characterized by somatic and autonomic dysfunctions. In particular, SCI above the ...

Design, Fabrication, and Administration of the Hand Active Sensation Test (HASTe)

The concept of personalizing neurologic rehabilitation, based on individual impairments, has experienced a recent surge. In parallel, the number of outcome measures of upper extremity motor performance has grown. However, clinicians and researchers lack practical, quantitative measures of the hand&#8217;s natural role as a receptor of the environment. The Hand Active Sensation Test (HASTe), developed by Williams and colleagues in 2006, is a valid and reliable measure of haptic performance. Though not available commercially, the HASTe can be fabricated from inexpensive materials, and it has been used successfully to identify impairments in haptic touch in individuals with stroke. (Williams, 2006). This paper presents the methods of design and fabrication of the HASTe testing kit, as well as a visual screen to be used during administration, and instructions for the tests administration and scoring.

Design, Fabrication, and Administration of the Hand Active Sensation Test HASTe

The Hand Active Sensation Test (HASTe) is a valid and reliable measure of haptic performance, which has been used successfully to identify impaired haptic touch in individuals with stroke. The purpose of this paper is to describe the design, fabrication and administration of the HASTe.

The concept of personalizing neurologic rehabilitation, based on individual impairments, has experienced a recent surge. In parallel, the number of ...

A Detailed Protocol for Perspiration Monitoring Using a Novel, Small, Wireless Device

Perspiration monitoring can be utilized for the detection of certain diseases, such as thermoregulation and mental disorders, particularly when the patients are unaware of such disorders or are having difficulty expressing their symptoms. Until now, several devices for perspiration monitoring have been developed; however, such devices tend to have a relatively large exterior, considerable power consumption, and/or less sensitivity.
Recently, we developed a small, wireless device for perspiration monitoring. The device consists of a temperature/relative humidity (T/RH) sensor, battery-driven small data logger, and silica gel as a desiccant in a small cylindrical exterior. The T/RH sensor is placed between the detection windows (through which the water vapor from the skin enters) and the silica gel. The underlying principle of the perspiration monitoring device is based on Fick&#39;s law of diffusion, which means that water vapor flux from the skin to the silica gel (i.e.&#160;transepidermal water loss and perspiration) can be captured by change in humidity at the T/RH sensor. In addition, a baseline subtraction method was adopted to distinguish perspiration and transepidermal water loss.
As shown in the previous report, the developed device can monitor the perspiration at any sites of the body in an easy, wireless manner. However, detailed methods of how to use the device have not been disclosed yet. In this article, therefore, we would like to show the point-by-point tutorials of how to use the device for perspiration monitoring, by showing the sympathetic activity test with the sympathetic skin response monitoring as an example.

Recently, we developed a small wireless device for perspiration monitoring. In this article, we present detailed protocols on how to use the device for perspiration monitoring with an example of the sympathetic activity test.

Perspiration monitoring can be utilized for the detection of certain diseases, such as thermoregulation and mental disorders, particularly when the ...

Minimally Invasive Muscle Embedding (MIME) - A Novel Experimental Technique to Facilitate Donor-Cell-Mediated Myogenesis

Skeletal muscle possesses regenerative capacity due to tissue-resident, muscle-fiber-generating (myogenic) satellite cells (SCs), which can form new muscle fibers under the right conditions. Although SCs can be harvested from muscle tissue and cultured in vitro, the resulting myoblast cells are not very effective in promoting myogenesis when transplanted into host muscle. Surgically exposing the host muscle and grafting segments of donor muscle tissue, or the isolated muscle fibers with their SCs onto host muscle, promotes better myogenesis compared to myoblast transplantation. We have developed a novel technique that we call Minimally Invasive Muscle Embedding (MIME). MIME involves passing a surgical needle through the host muscle, drawing a piece of donor muscle tissue through the needle track, and then leaving the donor tissue embedded in the host muscle so that it may act as a source of SCs for the host muscle. Here we describe in detail the steps involved in performing MIME in an immunodeficient mouse model that expresses a green fluorescent protein (GFP) in all of its cells. Immunodeficiency in the host mouse reduces the risk of immune rejection of the donor tissue, and GFP expression enables easy identification of the host muscle fibers (GFP+) and donor-cell-derived muscle fibers (GFP-). Our pilot data suggest that MIME can be used to implant an extensor digitorum longus (EDL) muscle from a donor mouse into the tibialis anterior (TA) muscle of a host mouse. Our data also suggest that when a myotoxin (barium chloride, BaCl2) is injected into the host muscle after MIME, there is evidence of donor-cell-derived myogenesis in the host muscle, with approximately 5%, 26%, 26% and 43% of the fibers in a single host TA muscle showing no host contribution, minimal host contribution, moderate host contribution, and maximal host contribution, respectively.

Minimally Invasive Muscle Embedding MIME - A Novel Experimental Technique to Facilitate Donor-Cell-Mediated Myogenesis

We describe a novel experimental technique that we call Minimally Invasive Muscle Embedding (MIME), which is based on the evidence that skeletal muscle tissue contains viable myogenic cells that can facilitate donor-cell-mediated myogenesis when implanted into a host muscle.

Skeletal muscle possesses regenerative capacity due to tissue-resident, muscle-fiber-generating (myogenic) satellite cells (SCs), which can form new ...

Structured Motor Rehabilitation After Selective Nerve Transfers

After severe nerve injuries, selective nerve transfers provide an opportunity to restore motor and sensory function. Functional recovery depends both on the successful re-innervation of the targets in the periphery and on the motor re-learning process entailing cortical plasticity. While there is an increasing number of methods to improve rehabilitation, their routine implementation in a clinical setting remains a challenge due to their complexity and long duration. Therefore, recommendations for rehabilitation strategies are presented with the aim of guiding medical doctors and therapists through the long-lasting rehabilitation process and providing step-by-step instructions for supporting motor re-learning.
Directly after nerve transfer surgery, no motor function is present, and therapy should focus on promoting activity in the sensory-motor cortex areas of the paralyzed body part. After about two to six months (depending on the severity and modality of injury, the distance of nerve regeneration and many other factors), the first motor activity can be detected via electromyography (EMG). Within this phase of rehabilitation, multimodal feedback is used to re-learn the motor function. This is especially critical after nerve transfers, as muscle activation patterns change due to the altered neural connection. Finally, muscle strength should be sufficient to overcome gravity/resistance of antagonistic muscles and joint stiffness, and more functional tasks can be implemented in rehabilitation.

Here, we present a protocol for the motor rehabilitation of patients with severe nerve injuries and selective nerve transfer surgery. It aims at restoring the motor function proposing several stages in patient education, early-stage therapy after surgery and interventions for rehabilitation after successful re-innervation of the nerve&#8217;s target.

After severe nerve injuries, selective nerve transfers provide an opportunity to restore motor and sensory function. Functional recovery depends both on ...