This work was supported by the Israel Science Foundation, grant # 306/15.

1. System Preparation
<ol>
	<li>Fill the tank with tap water up to a depth of about 20 cm to satisfy deep-water condition; clean the water surface of any contaminants that may affect the surface tension.</li>
	<li>Position the instrument carriage at the desired fetch.
	<ol>
		<li>Mount the Pitot tube and position it at the center of the airflow part of the test section.</li>
		<li>Mount the wave gauge on a computer-controlled vertical stage to enable its static calibration.</li>
	</ol>
	</li>
	<li>Position the LSG assembly at the desired fetch and at the lateral distance of about 7 cm from the wave gauge to eliminate interference of the wave gauge assembly with the optical path. 
	NOTE: The use of an opaque curtain is recommended to prevent the exposure of the PSD to ambient light, as well as to protect the environment from spurious reflections of the laser beam.
	<ol>
		<li>Align the laser positioned below the water tank so that the beam is directed vertically, and focus the beam.</li>
		<li>Position the fresnel lens within the test section as high as possible above the water surface to minimize the lens&#39;s disturbance of the air flow.</li>
		<li>Make sure that the deflected laser beam hits the lens in its central part under the extreme wind conditions planned in the experimental session.</li>
		<li>Mount the diffusive screen exactly at the focal plane of the lens, then check the horizontal and vertical alignment of both the lens and the screen.</li>
		<li>Make sure that any two parallel vertical laser beams hit the diffusive screen exactly at the center when the water surface is still. 
		NOTE: This can be tested using two identical lasers positioned at some distance from each other.</li>
		<li>Position the PSD making sure that the whole area of the diffusive screen is within the effective area of the detector. Perform focusing of the PSD lens by adjusting the lens settings to the actual distance between the lens and the screen.</li>
	</ol>
	</li>
</ol>
2. Calibration and Operation of Sensors
<ol>
	<li>Calibration of the wave gauge
	<ol>
		<li>Perform wave gauge calibration for each measuring location and each maximum wind velocity expected in the experimental run.
		<ol>
			<li>Set the vertical position of the sensor so that the mean water level is approximately in the middle of the sensing wires&#39; length.</li>
			<li>Set the blower speed to the desired value, and allow the wind to blow steadily for a sufficiently long time (2 - 3 min).</li>
			<li>Using an oscilloscope, manually adjust sensibility, gain, and offset of the wave gauge using the conditioner unit to ensure that the voltage values corresponding to the highest crest and the lowest trough expected in the wave field are within the range of the A/D converter (+/- 10 V).</li>
			<li>Shut down the blower for several minutes, until the water&#39;s surface becomes completely undisturbed.</li>
			<li>Verify that the submerged length is within expected maximum crest and trough values by moving the wave gauge vertically.</li>
			<li>Perform automatic calibration of the wave gauge using a custom-made routine in still water submerging the gauge at a number of specified depths and recording the mean voltage output during 5 s for each depth.</li>
			<li>Fit a quadratic calibration polynomial to the recorded data to obtain the dependence H(V), where H is the submergence depth (corresponding to the instantaneous surface elevation), as a function of the gauge output voltage V.</li>
			<li>Verify visually the quality of the fitted calibration polynomial (Figure 3).</li>
		</ol>
		</li>
	</ol>
	</li>
</ol>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/56480/56480fig3.jpg" /> 
Figure 3. Calibration curve of the wave gauge. <a href="http://cloudfront.jove.com/files/ftp_upload/56480/56480fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="2">
	<li>Calibration and adjustment of LSG
	<ol>
		<li>Verify the performance of the LSG after each displacement of the sensor assembly.
		<ol>
			<li>Using an optical wedge prism placed on a horizontal glass sheet, deviate the laser beam with respect to the optical axis simulating a known water surface slope.</li>
			<li>Sample the PSD outputs of the deviated laser beam spot at the diffusive screen using an oscilloscope or a custom-built data acquisition program.</li>
			<li>Compute the beam deflection angle and the slope from the measured coordinate laser beam spot coordinate; compare the result with the known wedge angle.</li>
			<li>Repeat the procedure for several deflection angles using one or more prisms. 
			NOTE: Wedge prisms with deflection angles ranging from 2.5&#176;&#160;to 17.5&#176;&#160;were used; if the test fails due to misalignment of PSD with the diffusive screen, adjust the PSD manually, to correct for misalignment. This procedure is performed manually using a 2D horizontal translation stage and a level and is very time consuming.</li>
		</ol>
		</li>
		<li>Verification of linearity of PSD and calibration procedure
		<ol>
			<li>Place an equally spaced grid that has been printed on a transparent sheet on the diffusive screen and orient it so that its axes, x and y, are aligned with the down and cross wind directions, respectively (Figure 4). 
			NOTE: The grid facilitates directing the laser beam to the desired locations on the diffusive screen conveniently and accurately either using a set of prisms or moving the laser below the diffusive screen in along-wind and crosswind directions.</li>
			<li>Using the set of prisms, deflect the vertical laser beam to obtain multiple radial positions of the laser beam spot on the diffusive screen while maintaining a constant azimuthal angle. 
			NOTE: Resolution of 1 cm and maximal radius of 7 cm is used for each of the 9 azimuthal angles.</li>
			<li>Move the laser spot to multiple positions in the x-direction, while keeping y coordinate constant, then change the direction of the movement to y, and keep x constant. 
			NOTE: Range and resolution used are similar to those from the previous section.</li>
			<li>Collect about 50 points on the grid in every calibration. 
			NOTE: The laser beam spot coordinates are acquired by PSD and evaluated using a standard two-channel oscilloscope connected to the PSD.
			<ol>
				<li>For each direction, use linear fit of the data to yield the calibration coefficients to convert the coordinates of the laser beam on the PSD sensor to the corresponding coordinates on the diffusive screen. 
				NOTE: An example of the PSD calibration is plotted in Figure 5 for a set of points taken along the centerline of the test section. The response of the sensor, and thus the calibration coefficients, is nearly identical in all directions when the axes of the diffusive screen and the sensor are aligned properly. The grid facilitates the calibration procedure, allowing an easy determination of the laser slope coordinates on the diffusive screen.</li>
			</ol>
			</li>
		</ol>
		</li>
	</ol>
	</li>
</ol>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/56480/56480fig4.jpg" /> 
Figure 4. The diffusive screen grid. The grid facilitates directing the laser beam to the desired locations on the diffusive screen conveniently and accurately, either using a set of prisms or moving the laser below the diffusive screen in along-wind and crosswind directions <a href="http://cloudfront.jove.com/files/ftp_upload/56480/56480fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/56480/56480fig5.jpg" /> 
Figure 5. PSD calibration curve. The figure demonstrates that the translation of the PSD output voltages to coordinates yields adequate results. <a href="http://cloudfront.jove.com/files/ftp_upload/56480/56480fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
3. Experimental Procedure and Data Acquisition
NOTE: See Supplementary Figure 1 for the user interface used in the following steps.
<ol>
	<li>Set blower frequency using a custom-built program user interface. 
	NOTE: Nearly stepwise increase of the wind velocity over initially undisturbed water surface was applied, followed by a steady airflow rate for a prescribed duration (120 s), and a nearly impulsive shut down of the blower.</li>
	<li>Determine the number of different steady wind flow rates and the required blower settings.</li>
	<li>Adjust the pressure transducer settings to the expected range of dynamic pressure variations detected by the Pitot tube.</li>
	<li>Make sure that at the beginning of each realization, there is no wind and the water surface is undisturbed (mirror smooth). Start data acquisition synchronously with operation of the blower.</li>
	<li>Record the instantaneous surface elevation, surface slope components in along- and crosswind directions, the Pitot tube output monitoring the mean wind velocity U, and the voltage variation from the blower controller at the prescribed sampling rate (300 Hz/channel were used). 
	NOTE: The voltage from wave-gauge acquired by the program is converted automatically to surface elevation using the calibration coefficients from the fit presented in Figure 3.</li>
	<li>Continue sampling for sufficient time to record the decaying wave field after the shutdown of the blower.</li>
	<li>Upon completion of the sampling, make sure that the automatic experimental procedure allows for sufficient time (depending on the system) to bring water surface to undisturbed condition prior to the initiation of the next run.</li>
	<li>Save all the recorded data for subsequent processing.</li>
	<li>Perform the prescribed number of realizations (usually 100 independent runs were found sufficient).</li>
	<li>Compute the ensemble-averaged parameters of the recorded data as a function of the time elapsed since the initiation of the blower.</li>
	<li>Repeat the whole procedure for the next setting of the blower corresponding to the selected target wind velocity in the test section.</li>
</ol>

<ol>
	<li>Sir William Thomson, F. R. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydrokinetic+solutions+and+observations.">Hydrokinetic solutions and observations.</a> Philosophical Magazine. 42, 362-377 (1871).</li><li>Jeffreys, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+formation+of+water+waves+by+wind.">On the formation of water waves by wind.</a> Proc. Roy. Soc. London Ser. A. 107, 189-206 (1925).</li><li>Miles, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+generation+of+surface+waves+by+shear+flows.">On the generation of surface waves by shear flows.</a> J. Fluid Mech. 3 (2), 185-204 (1957).</li><li>Phillips, O. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+generation+of+waves+by+turbulent+wind.">On the generation of waves by turbulent wind.</a> J. Fluid Mech. 2 (5), 417-445 (1957).</li><li>Plate, E. J., Chang, P. C., Hidy, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experiments+on+the+generation+of+small+water+waves+by+wind.">Experiments on the generation of small water waves by wind.</a> J. Fluid Mech. 35 (4), 625-656 (1969).</li><li>Mitsuyasu, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+growth+of+the+spectrum+of+wind-generated+waves+I.">On the growth of the spectrum of wind-generated waves I.</a> Rep. Res. Inst. Appl. Mech., Kyushu Univ. 16 (55), 459-482 (1968).</li><li>Toba, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Local+balance+in+the+air-sea+boundary+processes,+I.+On+the+growth+process+of+wind+waves.">Local balance in the air-sea boundary processes, I. On the growth process of wind waves.</a> J. Oceanog. Soc. Japan. 28, 109-120 (1972).</li><li>Toba, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Local+balance+in+the+air-sea+boundary+processes.+III.+On+the+spectrum+of+wind+waves.">Local balance in the air-sea boundary processes. III. On the spectrum of wind waves.</a> J. Oceanogr. Soc. Japan. 29, 209-220 (1973).</li><li>Hara, T., Bock, E. J., Donelan, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Frequency-wavenumber+spectrum+of+wind-generated+gravity-capillary+waves.">Frequency-wavenumber spectrum of wind-generated gravity-capillary waves.</a> J. Geoph. Res. 102, 1061-1072 (1997).</li><li>Caulliez, G., Gu&#233;rin, C. -. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Higher-order+statistical+analysis+of+short+wind+wave+fields.">Higher-order statistical analysis of short wind wave fields.</a> J. Geophys. Res. 117, C06002 (2012).</li><li>Mitsuyasu, H., Rikiishi, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+growth+of+duration-limited+wind+waves.">The growth of duration-limited wind waves.</a> J. Fluid Mech. 85, 705-730 (1978).</li><li>Kawai, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Generation+of+initial+wavelets+by+instability+of+a+coupled+shear+flow+and+their+evolution+to+wind+waves.">Generation of initial wavelets by instability of a coupled shear flow and their evolution to wind waves.</a> J. Fluid Mech. 93 (4), 661-703 (1979).</li><li>Waseda, T., Toba, Y., Tulin, M. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adjustment+of+wind+waves+to+sudden+changes+of+wind+speed.">Adjustment of wind waves to sudden changes of wind speed.</a> J. Oceanography. 57, 519-533 (2001).</li><li>Uz, B. M., Hara, T., Bock, E. J., Donelan, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Laboratory+observations+of+gravity-capillary+waves+under+transient+wind+forcing.">Laboratory observations of gravity-capillary waves under transient wind forcing.</a> J. Geophys. Res.: Oceans. 108 (C2), (2003).</li><li>Hwang, P. A., Wang, D. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Field+measurements+of+duration-limited+growth+of+wind-generated+ocean+surface+waves+at+young+stage+of+development.">Field measurements of duration-limited growth of wind-generated ocean surface waves at young stage of development.</a> J. Phys. Oceanogr. 34 (10), 2316-2326 (2004).</li><li>Hwang, P. A., Garc&#237;a-Nava, H., Ocampo-Torres, F. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Observations+of+wind+wave+development+in+mixed+seas+and+unsteady+wind+forcing.">Observations of wind wave development in mixed seas and unsteady wind forcing.</a> J. Phys. Oceanogr. 41, 2340-2359 (2011).</li><li>Liberzon, D., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+study+of+the+initial+stages+of+wind+waves'+spatial+evolution.">Experimental study of the initial stages of wind waves' spatial evolution.</a> J. Fluid Mech. 681, 462-498 (2011).</li><li>Miles, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+generation+of+surface+waves+by+shear+flows.+Part+2.">On generation of surface waves by shear flows. Part 2.</a> J. Fluid Mech. 6 (4), 568-582 (1959).</li><li>Plant, W. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+relationship+between+wind+stress+and+wave+slope.">A relationship between wind stress and wave slope.</a> J. Geophys. Res. 87, 1961-1967 (1982).</li><li>Zavadsky, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characterization+of+turbulent+air+flow+over+evolving+water-waves+in+a+wind-wave+tank.">Characterization of turbulent air flow over evolving water-waves in a wind-wave tank.</a> J. Geophys. Res. 117, C00J19 (2012).</li><li>Zavadsky, A., Liberzon, D., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Statistical+analysis+of+the+spatial+evolution+of+the+stationary+wind+wave+field.">Statistical analysis of the spatial evolution of the stationary wind wave field.</a> J. Phys. Oceanogr. 43, 65-79 (2013).</li><li>Zavadsky, A., Benetazzo, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+two-dimensional+structure+of+short+gravity+waves+in+a+wind+wave+tank.">On the two-dimensional structure of short gravity waves in a wind wave tank.</a> Phys. Fluids. 29 (1), 016601 (2017).</li><li>Zavadsky, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigation+of+statistical+parameters+of+the+evolving+wind+wave+field+using+Laser+Slope+Gauge.">Investigation of statistical parameters of the evolving wind wave field using Laser Slope Gauge.</a> Phys. Fluids. 29 (5), (2017).</li><li>Zavadsky, A., Shemer, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Water+waves+excited+by+near-impulsive+wind+forcing.">Water waves excited by near-impulsive wind forcing.</a> J. Fluid Mech. , (2017).</li></ol>

Authors have nothing to disclose.

The present experimental protocol is aimed at quantitative characterization of a wave field under unsteady wind forcing that evolves in time and space. Since wind-waves are essentially random and three-dimensional, and thus vary quickly in time and space, records of individual realizations of a growing wind-wave field under time-dependent wind forcing can only provide qualitative estimates of the governing wave parameters. To achieve the goal of this protocol and obtain statistically reliable time- and fetch-dependent wa...

Since ancient times, it has been well known that waves on water surfaces are excited by wind. The current understanding of the physical mechanisms that govern this process is far from satisfactory. Numerous theories attempting to describe wind-wave generation were proposed over the years1,2,3,4, however their reliable experimental validation is not yet available. Measurements of random wind-waves in the ocean are extremely challenging due to unpredictable wind that may vary quickly in direction as well as in magnitude. Laboratory experiments have the advantage of controllable conditions that enable prolonged and repeatable measurements.
Under steady wind forcing in the laboratory environment, wind-waves evolve in space. Early laboratory experiments on waves under steady forcing performed decades ago were limited to instantaneous surface elevation measurements5,6,7,8. More recent studies also employed various optical techniques to measure instantaneous water surface inclination angle, such as LSG9,10. Those measurements allowed getting some limited qualitative information on the three-dimensional structure of wind-wave fields. When wind forcing is unstable, as it is in field experiments, additional complexity is introduced to the problem of water waves&#39; excitation by wind, since the statistical parameters of the resulting wave field vary not just in space but in time as well. The attempts made so far to describe wave evolution patterns qualitatively and quantitatively under time-dependent forcing were only partially successful11,12,13,14,15,16. The relative contribution of different plausible physical mechanisms that may lead to excitation and growth of waves due to wind action remains largely unknown.
Our experimental facility was designed with the purpose of enabling the accumulation of accurate and diverse statistical information on the variation of wind-wave field characteristics under either steady or unsteady wind forcing. Two major factors facilitated carrying out these detailed studies. First, the modest size of the facility results in relatively short characteristic evolution scales in time and space. Second, the whole experiment is fully controlled by a computer, thus enabling the performance of experimental runs under different experimental conditions automatically and practically without human intervention. These features of the experimental set-up are of crucial importance in performing experiments on waves excited from rest by impulsive wind.
Spatial growth of wind-waves under steady forcing has been studied in our facility for a range of wind velocities17. Results were compared with growth rate estimates based on the Miles18 theory as presented by Plant19. The comparison revealed that the experimental results differ notably from the theoretical predictions. Additional important parameters were also obtained in17, such as mean pressure drop in the test section, as well as the absolute values and phases of characteristic static pressure fluctuations. The shear stress at the air-water interface is essential for characterization of momentum and energy transfer between wind and waves17,19. Therefore, detailed measurements of the logarithmic boundary layer and the turbulent fluctuations in the air flow above water waves were performed at numerous fetches and wind velocities20. The values of the friction velocity u* at the air-water interface determined in this study were used to obtain dimensionless statistical parameters of the wind-waves measured in our facility21. These values were compared with the corresponding dimensionless parameters obtained in larger experimental installations and field experiments. It was demonstrated previously21 that with proper scaling, the important characteristics of the wind-wave field obtained in our small-scale facility do not differ significantly from the corresponding data accumulated in larger laboratory installations and open sea measurements. These parameters include spatial growth of the representative wave height and wave length, the shape of the frequency spectrum of the surface elevation, as well as the values of higher statistical moments.
The subsequent studies carried out in our facility22,23 showed that wind waves are essentially random and three-dimensional. To get a better insight into the 3D structure of wind waves, an attempt was made to perform quantitative time-dependent measurements of water surface elevation over an extended area using stereo video imaging22. Due to inadequate computer power available at present and processing algorithms that are not yet sufficiently effective, these attempts proved to be only partially successful. However, it was demonstrated that combined use of a conventional capacitance-type wave gauge and the LSG provides valuable information on the spatial structure of wind waves. Simultaneous application of both those instruments enables independent measurements with high temporal resolution of the instantaneous surface elevation and of the two components of the instantaneous surface slope23. These measurements allow estimation of both the dominant frequency and dominant wave length of the waves, as well as providing insight into the wave structure in the direction normal to the wind. A pitot tube, which can be moved vertically by a computer-controlled motor, complements the set of sensors and is used for measurements of wind velocity.
All those studies made clear that randomness and three-dimensionality of wind waves result in significant variability of the measured parameters even for steady wind forcing and a single measuring location. Thus, prolonged measurements with duration commensurate with the characteristic time scales of the measured wave field are needed to accumulate sufficient information for extracting reliable statistical quantities. To gain valuable physical insight into the mechanisms governing spatial variation of the wave field, it is imperative to carry out measurements at numerous locations and for as many values of the wind flow rate as possible in the test section. To achieve this goal, it is thus highly desirable to apply an automated experimental procedure.
Experiments on waves excited by unsteady wind forcing introduce an additional level of complexity. In such studies, it is imperative to relate the instantaneous measured parameters to the instantaneous level of the wind speed. Consider experiments on waves excited from rest by a nearly impulsive wind forcing as an important example. In this case, numerous independent measurements are needed of the wind-wave field evolving under the action of wind that varies in time following the same prescribed pattern24. Meaningful statistical parameters, expressed as a function of time elapsed since the initiation of air flow, are then calculated by averaging the data extracted from the accumulated ensemble of independent realizations. This undertaking may involve tens and hundreds of hours of continuous sampling. The total duration of experimental sessions required to accomplish such an ambitious task renders the whole approach unfeasible, unless the experiment is fully automated. No such fully computerized experimental procedure in wind-wave facilities has been developed until recently. That is among the main reasons for the lack of reliable statistical data on wind waves under unsteady forcing.
Since the facility used for the experiment is not constructed from commercially available, off-the-shelf hardware, a brief description of its main parts is provided here.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/56480/56480fig1.jpg" /> 
Figure 1. Schematic (not to scale) view of the experimental facility. 1 - blower; 2 - inflow settling chamber; 3 - outflow settling chamber; 4 - silencer boxes; 5 - test section; with a 6 - beach; 7 - heat exchanger; 8 - honeycomb; 9 - nozzle; 10 - wavemaker; 11 - flap; 12 - instrument carriage; 13 - wave gauge driven by a stepper motor; 14 - Pitot tube driven by a stepper motor. <a href="http://cloudflare.jove.com/files/ftp_upload/56480/56480fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
The experimental facility consists of a closed loop wind tunnel mounted over a wave tank (a schematic view is shown in Figure 1). The test section is 5 m long, 0.4 m wide, and 0.5 m deep. The sidewalls and floor are made of 6 mm thick glass plates and are enclosed within a frame made of aluminum profiles. A 40-cm long flap provides a smooth expansion of the airflow cross-section from the nozzle to the water surface. Wave energy absorbing beach made of porous packing material is located at the far end of the tank. A computer-controlled blower allows attaining mean air flow velocity in the test section up to 15 m/s.
The custom-made capacitance-type 100 mm-long wave gauge is made of anodized tantalum. 0.3 mm wire is mounted on a vertical stage driven by a PC-controlled step motor designed for wave gauge calibration. A Pitot tube with a diameter of 3 mm is used for measuring the dynamic pressure in the central airflow part of the test section.
The LSG, measuring instantaneous 2D water surface slope, is installed on a frame detached from the test section that can be positioned at any location along the tank (Figure 2). LSG consists of four main parts: a laser diode, a Fresnel lens, a diffusive screen, and a Position Sensing Detector (PSD) assembly. The laser diode generates a 650 nm (red), 200 mW focusable laser beam with diameter of about 0.5 mm. The 26.4 cm diameter Fresnel lens with focal length of 22.86 cm directs the incoming laser beam to the 25 x&#160;25 cm2 diffusive screen located in the back focal plane of the lens.
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/56480/56480fig2.jpg" /> 
Figure 2. Schematic view of the Laser Slope Gauge (LSG). 1 - laser diode; 2 - Fresnel lens; 3 - diffusive screen; 4 - Position Sensor Detector (PSD). <a href="http://cloudflare.jove.com/files/ftp_upload/56480/56480fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
This protocol describes the procedure that allows performing experiments in which numerous parameters characterizing unsteady waves are measured simultaneously under time-dependent wind forcing. The procedure can be adjusted to any desired dependence of wind velocity on time that can be attained in view of the technical limitations of the experimental facility. The present protocol describes specifically experiments in which in every realization, wind starts nearly impulsively over initially calm water. The steady wind forcing then lasts for long enough that the wind-wave field everywhere in the test section attains quasi-steady state. The wind eventually is shut down, again nearly impulsively. At all stages, multiple wave parameters are recorded. The procedure that allows computation of numerous statistically representative ensemble-averaged quantities characterizing the instantaneous local wind-wave field is novel, and was developed in the course of recent experiments carried out in our facility22,23,24.

<table><tbody><tr><td>PSD</td><td>THORLABS</td><td>PDP90A</td><td></td></tr><tr><td>Laser Diode</td><td></td><td></td><td>any laser pointer &amp;le; 200 mW</td></tr><tr><td>Aspheric Fresnel Lens</td><td>EDMUND OPTICS</td><td>#46-390</td><td>Diameter 10.4&#039;&#039;, Focal length 9&#039;&#039;</td></tr><tr><td>Wave-gauge</td><td></td><td></td><td>custom made</td></tr><tr><td>Pressure Transducer</td><td>MAMAC SYSTEMS</td><td>PR-274-R2-VDC</td><td></td></tr><tr><td>Signal Conditioner</td><td></td><td></td><td>custom made</td></tr><tr><td>Diffusive screen</td><td>EDMUND OPTICS</td><td>#02-147</td><td></td></tr><tr><td>Water tank</td><td></td><td></td><td>custome made</td></tr><tr><td>A/D card PCI-6221</td><td>National Instruments</td><td>779066-01</td><td></td></tr><tr><td>Pitot tube</td><td>KIMO Instruments</td><td>12971</td><td></td></tr><tr><td>15&amp;deg; Nom. VIS-NIR Coated, Wedge Prism</td><td>EDMUND OPTICS</td><td>#47-624</td><td></td></tr><tr><td>10&amp;deg; Nom. VIS 0&amp;deg; Coated, Wedge Prism</td><td>EDMUND OPTICS</td><td>#49-444</td><td></td></tr><tr><td>2.5&amp;deg; Nom. Fused Silica Wedge Prism Uncoated</td><td>EDMUND OPTICS</td><td>#84-863</td><td></td></tr><tr><td>4&amp;deg; Nom. Uncoated, Wedge Prism</td><td>EDMUND OPTICS</td><td>#43-650</td><td></td></tr><tr><td>5.0&amp;deg; Nom. Fused Silica Wedge Prism Uncoated</td><td>EDMUND OPTICS</td><td>#84-865</td><td></td></tr><tr><td>LabView Full Development System</td><td>National Instruments</td><td>776670-35</td><td></td></tr></tbody></table>

measurements of waves in a wind-wave tank under steady and time-varying wind forcing

This manuscript describes an experimental procedure that allows obtaining diverse quantitative information on temporal and spatial evolution of water waves excited by time-dependent and steady wind forcing. Capacitance-type wave gauge and Laser Slope Gauge (LSG) are used to measure instantaneous water surface elevation and two components of the instantaneous surface slope at a number of locations along the test section of a wind-wave facility. The computer-controlled blower provides airflow over the water in the tank whose rate can vary in time. In the present experiments, the wind speed in the test section initially increases quickly from rest to the set value. It is then kept constant for the prescribed duration; finally, the airflow is shut down. At the beginning of each experimental run, the water surface is calm and there is no wind. Operation of the blower is initiated simultaneously with the acquisition of data provided by all sensors by a computer; data acquisition continues until the waves in the tank fully decay. Multiple independent runs performed under identical forcing conditions allow determining statistically reliable ensemble-averaged characteristic parameters that quantitatively describe wind-waves&#39; variation in time for the initial development stage as a function of fetch. The procedure also allows characterizing the spatial evolution of the wave field under steady wind forcing, as well as decay of waves in time, once the wind is shut down, as a function of fetch.

The representative ensemble-averaged results are plotted in Figure 6, Figure 7, and Figure 8. The variation of the RMS values of the instantaneous surface elevation &#60;&#951;2&#62;1/2 that characterizes the amplitude of random wind waves as presented in Figure 6 as a function of time elapsed since initiation of the b...

Watch this Scientific Journal Video about Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing at JoVE.com

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

This manuscript describes a fully computer-controlled procedure that allows obtaining reliable statistical parameters from experiments of water waves excited by steady and unsteady wind forcing in a small-scale facility.

This manuscript describes an experimental procedure that allows obtaining diverse quantitative information on temporal and spatial evolution of water ...

measurements-waves-wind-wave-tank-under-steady-time-varying-wind

Universidad de Cartagena UDEC

Research

Education

JoVE Journal

JoVE Core

Engineering

Physics

Electrical Engineering

Unit 1

First and Second-Order Circuits

Waves

SCIENTISTS IN ACTION

8.6K 조회수.  Tel-Aviv University. This manuscript describes a fully computer-controlled procedure that allows obtaining reliable statistical parameters from experiments of water waves excited by steady and unsteady wind forcing in a small-scale facility.

비디오: Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

Exploring the Effects of Atmospheric Forcings on Evaporation: Experimental Integration of the Atmospheric Boundary Layer and Shallow Subsurface

Evaporation is directly influenced by the interactions between the atmosphere, land surface and soil subsurface. This work aims to experimentally study evaporation under various surface boundary conditions to improve our current understanding and characterization of this multiphase phenomenon as well as to validate numerical heat and mass transfer theories that couple Navier-Stokes flow in the atmosphere and Darcian flow in the porous media. Experimental data were collected using a unique soil tank apparatus interfaced with a small climate controlled wind tunnel. The experimental apparatus was instrumented with a suite of state of the art sensor technologies for the continuous and autonomous collection of soil moisture, soil thermal properties, soil and air temperature, relative humidity, and wind speed. This experimental apparatus can be used to generate data under well controlled boundary conditions, allowing for better control and gathering of accurate data at scales of interest not feasible in the field. Induced airflow at several distinct wind speeds over the soil surface resulted in unique behavior of heat and mass transfer during the different evaporative stages.

A protocol for the design and construction of a soil tank interfaced to a small climate controlled wind tunnel to study the effects of atmospheric forcings on evaporation is presented. Both the soil tank and wind tunnel are instrumented with sensor technologies for the continuous in situ measurement of environmental conditions.

증발에 대기 강제력의 효과를 탐구 : 대기 경계층과 얕은 표면 하의의 실험 통합

Evaporation is directly influenced by the interactions between the atmosphere, land surface and soil subsurface. This work aims to experimentally study ...

연구

환경과학

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Two different experimental methods for determining the threshold of particle motion as a function of geometrical properties of the bed from laminar to turbulent flow conditions are presented. For that purpose, the incipient motion of a single bead is studied on regular substrates that consist of a monolayer of fixed spheres of uniform size that are regularly arranged in triangular and quadratic symmetries. The threshold is characterized by the critical Shields number. The criterion for the onset of motion is defined as the displacement from the original equilibrium position to the neighboring one. The displacement and the mode of motion are identified with an imaging system. The laminar flow is induced using a rotational rheometer with a parallel disk configuration. The shear Reynolds number remains below 1. The turbulent flow is induced in a low-speed wind tunnel with open jet test section. The air velocity is regulated with a frequency converter on the blower fan. The velocity profile is measured with a hot wire probe connected to a hot film anemometer. The shear Reynolds number ranges between 40 and 150. The logarithmic velocity law and the modified wall law presented by Rotta are used to infer the shear velocity from the experimental data. The latter is of special interest when the mobile bead is partially exposed to the turbulent flow in the so-called hydraulically transitional flow regime. The shear stress is estimated at onset of motion. Some illustrative results showing the strong impact of the angle of repose, and the exposure of the bead to shear flow are represented in both regimes.

Two different methods for characterizing the incipient particle motion of a single bead as a function of the sediment bed geometry from laminar to turbulent flow are presented.

Two different experimental methods for determining the threshold of particle motion as a function of geometrical properties of the bed from laminar to ...

공학

Simultaneous Measurement of Turbulence and Particle Kinematics Using Flow Imaging Techniques

Numerous problems in scientific and engineering fields involve understanding the kinematics of particles in turbulent flows, such as contaminants, marine micro-organisms, and/or sediments in the ocean, or fluidized bed reactors and combustion processes in engineered systems. In order to study the effect of turbulence on the kinematics of particles in such flows, simultaneous measurements of both the flow and particle kinematics are required. Non-intrusive, optical flow measurement techniques for measuring turbulence, or for tracking particles, exist but measuring both simultaneously can be challenging due to interference between the techniques. The method presented herein provides a low cost and relatively simple method to make simultaneous measurements of the flow and particle kinematics. A cross section of the flow is measured using a particle image velocimetry (PIV) technique, which provides two components of velocity in the measurement plane. This technique utilizes a pulsed-laser for illumination of the seeded flow field that is imaged by a digital camera. The particle kinematics are simultaneously imaged using a light emitting diode (LED) line light that illuminates a planar cross section of the flow that overlaps with the PIV field-of-view (FOV). The line light is of low enough power that it does not affect the PIV measurements, but powerful enough to illuminate the larger particles of interest imaged using the high-speed camera. High-speed images that contain the laser pulses from the PIV technique are easily filtered by examining the summed intensity level of each high-speed image. By making the frame rate of the high-speed camera incommensurate with that of the PIV camera frame rate, the number of contaminated frames in the high-speed time series can be minimized. The technique is suitable for mean flows that are predominantly two-dimensional, contain particles that are at least 5 times the mean diameter of the PIV seeding tracers, and are low in concentration.

The technique described herein offers a low cost and relatively simple method to simultaneously measure particle kinematics and turbulence in flows with low particle concentrations. The turbulence is measured using particle image velocimetry (PIV), and particle kinematics are calculated from images obtained with a high-speed camera in an overlapping field-of-view.

Numerous problems in scientific and engineering fields involve understanding the kinematics of particles in turbulent flows, such as contaminants, marine ...

Power Input Measurements in Stirred Bioreactors at Laboratory Scale

The power input in stirred bioreactors is an important scaling-up parameter and can be measured through the torque that acts on the impeller shaft during rotation. However, the experimental determination of the power input in small-scale vessels is still challenging due to relatively high friction losses inside typically used bushings, bearings and/or shaft seals and the accuracy of commercially available torque meters. Thus, only limited data for small-scale bioreactors, in particular single-use systems, is available in the literature, making comparisons among different single-use systems and their conventional counterparts difficult.
This manuscript provides a protocol on how to measure power inputs in benchtop scale bioreactors over a wide range of turbulence conditions, which can be described by the dimensionless Reynolds number (Re). The aforementioned friction losses are effectively reduced by the use of an air bearing. The procedure on how to set up, conduct and evaluate a torque-based power input measurement, with special focus on cell culture typical agitation conditions with low to moderate turbulence (100 &#60; Re &#60; 2&#183;104), is described in detail. The power input of several multi-use and single-use bioreactors is provided by the dimensionless power number (also called Newton number, P0), which is determined to be in the range of P0 &#8776; 0.3 and P0 &#8776; 4.5 for the maximum Reynolds numbers in the different bioreactors.

The power input in stirred bioreactors can be measured through the torque that acts on the impeller shaft during rotation. This manuscript describes how an air bearing can be used to effectively reduce friction losses observed in mechanical seals and improve the accuracy of power input measurements in small-scale vessels.

The power input in stirred bioreactors is an important scaling-up parameter and can be measured through the torque that acts on the impeller shaft during ...

생체공학

안정적이고 생물학적으로 유의미한 팬텀 물질의 제조

A Stable Phantom Material for Optical and Acoustic Imaging

Establishing tissue-mimicking biophotonic phantom materials that provide long-term stability are imperative to enable the comparison of biomedical imaging devices across vendors and institutions, support the development of internationally recognized standards, and assist the clinical translation of novel technologies. Here, a manufacturing process is presented that results in a stable, low-cost, tissue-mimicking copolymer-in-oil material for use in photoacoustic, optical, and ultrasound standardization efforts.
The base material consists of mineral oil and a copolymer with defined Chemical Abstract Service (CAS) numbers. The protocol presented here yields a representative material with a speed of sound c(f) = 1,481 &#177; 0.4 m&#183;s-1 at 5 MHz (corresponds to the speed of sound of water at 20 &#176;C), acoustic attenuation &#945;(f) = 6.1 &#177; 0.06 dB&#183;cm-1 at 5 MHz, optical absorption &#181;a(&#955;) = 0.05 &#177; 0.005 mm-1 at 800 nm, and optical scattering &#181;s&#39;(&#955;) = 1 &#177; 0.1 mm-1 at 800 nm. The material allows independent tuning of the acoustic and optical properties by respectively varying the polymer concentration or light scattering (titanium dioxide) and absorbing agents (oil-soluble dye). The fabrication of different phantom designs is displayed and the homogeneity of the resulting test objects is confirmed using photoacoustic imaging.
Due to its facile, repeatable fabrication process and durability, as well as its biologically relevant properties, the material recipe has high promise in multimodal acoustic-optical standardization initiatives.

저자 스포트라이트: 광학 및 음향 이미징을 위한 안정적인 팬텀 재료  

This protocol describes the fabrication of a stable, biologically relevant phantom material for optical and acoustic biomedical imaging applications, featuring independently tunable acoustic and optical properties.

광학 및 음향 이미징을 위한 안정적인 팬텀 소재

Establishing tissue-mimicking biophotonic phantom materials that provide long-term stability are imperative to enable the comparison of biomedical imaging ...

의학

Stability of Floating Vessels

Source: Alexander S Rattner and Kevin Rao Li Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA
 The objective of this experiment is to demonstrate the phenomenon of stability of floating vessels - the ability to self-right when rolled over to the side by some external force. Careful design of hull shapes and internal mass distribution enables seagoing vessels to be stable with low drafts (submerged depth of hull), improving vessel maneuverability and reducing drag. 
In this experiment, a model boat will first be modified to enable adjustment of its center of mass (representing different cargo loadings) and automated tracking of its roll angle. The boat will be placed in a container of water, and tipped to different angles with varying heights of its center of mass. Once released, the capsizing (tipping over) or oscillating motion of the boat will be tracked with a digital camera and video analysis software. Results for the maximum stable roll angle and frequency of oscillation will be compared with theoretical values. Stability calculations will be performed using geometric and structural properties of the boat determined in a computer aided design environment.

The Buoyant Force and Stability of Floating Vessels

플로팅 선박의 안정성

Source: Alexander S Rattner and Kevin Rao Li Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA
 The ...

교육

JoVE Science Education

기계공학

Turbulence Sphere Method: Evaluating Wind Tunnel Flow Quality

Source: Jose Roberto Moreto and Xiaofeng Liu, Department of Aerospace Engineering, San Diego State University, San Diego, CA
Wind tunnel tests are useful in the design of vehicles and structures that are subjected to airflow during their use. Wind tunnel data are generated by applying a controlled air flow to a model of the object being studied. The test model usually has a similar geometry but is a smaller scale compared to the full-sized object. To ensure accurate and useful data is collected during low speed wind tunnel tests, there must be a dynamic similarity of the Reynolds number between the tunnel flow field over the testing model and the actual flow field over the full-sized object.
In this demonstration, wind tunnel flow over a smooth sphere with well-defined flow characteristics will be analyzed. Because the sphere has well-defined flow characteristics, the turbulence factor for the wind tunnel, which correlates the effective Reynolds number to the test Reynolds number, can be determined, as well as the free-stream turbulence intensity of the wind tunnel.

Turbulence Measurements at Varying Air Speeds

난류 구체 방식: 풍동 흐름 품질 평가

Source: Jose Roberto Moreto and Xiaofeng Liu, Department of Aerospace Engineering, San Diego State University, San Diego, CA
Wind tunnel tests are useful ...

항공공학

Measuring Turbulent Flows

Source: Ricardo Mejia-Alvarez and Hussam Hikmat Jabbar, Department of Mechanical Engineering, Michigan State University, East Lansing, MI
Turbulent flows exhibit very high frequency fluctuations that require instruments with high time-resolution for their appropriate characterization. Hot-wire anemometers have a short enough time-response to fulfill this requirement. The purpose of this experiment is to demonstrate the use of hot-wire anemometry to characterize a turbulent jet.
In this experiment, a previously calibrated hot-wire probe will be used to obtain velocity measurements at different positions within the jet. Finally, we will demonstrate a basic statistical analysis of the data to characterize the turbulent field.

Measuring Turbulent Flows Using Hot-Wire Anemometers

난류 측정

Source: Ricardo Mejia-Alvarez and Hussam Hikmat Jabbar, Department of Mechanical Engineering, Michigan State University, East Lansing, MI
Turbulent flows ...

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

요약

더 많은 비디오 탐색

이 비디오의 챕터

증발에 대기 강제력의 효과를 탐구 : 대기 경계층과 얕은 표면 하의의 실험 통합

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Simultaneous Measurement of Turbulence and Particle Kinematics Using Flow Imaging Techniques

Power Input Measurements in Stirred Bioreactors at Laboratory Scale

광학 및 음향 이미징을 위한 안정적인 팬텀 소재

광학 및 음향 이미징을 위한 안정적인 팬텀 소재

광학 및 음향 이미징을 위한 안정적인 팬텀 소재

플로팅 선박의 안정성

난류 구체 방식: 풍동 흐름 품질 평가

난류 측정