Name: dry film photoresist-based electrochemical microfluidic biosensor platform: device fabrication, on-chip assay preparation, and system operation
Uploaded: 2017-09-19T12:30:00.000+00:00
Duration: 13 min 42 s
Description: Watch this Scientific Journal Video about Dry Film Photoresist-based Electrochemical Microfluidic Biosensor Platform: Device Fabrication, On-chip Assay Preparation, and System Operation at JoVE.com

作者希望感谢德国研究基金会 (DFG) 在赠款号 ur 70/10-01 和 ur 70/12-01 的部分资助这项工作。

1. 利用 DFR 技术制备微流控生物传感器 <ol> <li> PI 晶片的制备。
	<ol> <li> 将 PI 衬底切成6个圆片。将 PI 晶片放入烤箱中120和 #176; C 用于脱水烘烤约1小时. </li>
	</ol> </li> <li> 第一个光刻步骤用于剥离过程. 
	<ol> <li> 将自旋涂布机的30秒旋转时间定为 3000 rpm, 加速度为 2000 rpm/秒. 将 PI 晶片放在自旋涂布机上, 并将其固定, 应用真空。免除2毫升的抵抗, 使剥离过程, 并启动自旋涂布机程序。从自旋涂布机上取下晶片, 并在热板上 soft-bake PI 晶片2分钟, 在100和 #176; C. </li>
		<li> 调整所需的掩码以将 PI 晶片上的电极与肉眼进行阵列, 并将其暴露给400兆焦耳/cm 2 UV 光 (365 nm)。将晶片放在一个装有抗阻匹配显影液的碗里, 让它稍微摇动1分钟. </li>
		<li> 在去除多余的抗性后, 使用淋浴器在湿的长凳上用去离子水 (DI 水) 冲洗 PI 晶片, 然后用压缩空气将其烘干. </li>
	</ol> </li> <li> 沉积铂以形成电极。
	<ol> <li> 使用标准的物理气相沉积过程将200纳米铂沉积到晶片上 19 。
		<li> 将晶片放入碗中。添加匹配的卸妆到碗, 并删除剥离抵抗, 而轻微晃动的晶圆在一个轨道振动筛, 直到所有过剩的白金被删除。如步骤1.2.3 所述, 冲洗和烘干 PI 晶片. </li>
	</ol> </li> <li> 第二个光刻步骤: 形成保温层. 
	<ol> <li> 将 PI 晶片放入预热到120和 #176 的烤箱中; C 为5分钟, 使其脱水. </li>
		<li> 将自旋式涂布机的第一步按 500 rpm 的旋转时间的5秒进行编程。计划的第二步为三十年代在4000转每分钟, 以加速度700转/秒. </li>
		<li> 将 PI 晶片放在自旋涂布机上, 并将其固定, 应用真空。在启动自旋涂布机程序之前, 免除4毫升适当的氧光刻胶. </li>
		<li> 软烤涂覆的硅片在95和 #176; C 在热板上. </li>
		<li> 使用相应的校准标记和目镜调整晶片上的保温层的掩码。将硅片暴露为100兆焦耳/cm 2 UV 光 (365 nm). </li>
		<li> 对于后烘烤, 将晶片放在预热的热板上, 在95和 #176 处放置2分钟; C. </li>
		<li> 将晶片放入碗中, 并与合适的显影剂一起开发 ( 例如, 在 SU-8 上, 在轨道振动筛上的 1-甲氧基-2-丙基 acetat, 用于2分钟). </li>
		<li> 先用异丙醇冲洗 PI 晶片, 然后冲洗并干燥, 如步骤1.2.3 中所述. </li>
		<li> 硬-在烤箱中烘烤3小时的光刻胶, 在 150 #176; C. </li>
	</ol> </li> <li> 等离子辅助清洗电极。
	<ol> <li> 要除去光刻胶残留物, 请使用标准等离子单元的氧等离子体。启动清洁程序, 使用 200 W 低频电源与 100% O 2 流, 速率为 250 sccm, 总时间为 3 min. </li>
		<li> 将 PI 晶片放入等离子室, 用玻璃盖固定在接地板上的晶片, 并启动等离子过程. </li>
	</ol> </li> <li> 银和氯化银沉积: 创建芯片上的参考电极。
	<ol> <li> 钝化用 UV 敏感的胶带将晶片的铂接触垫。将铝箔切成5毫米宽和11厘米长的条纹, 并将其附着在晶片上, 以保护不被银沉积的部分. </li>
		<li> 对于银沉积, 将声波浴 (35 赫) 放入通风柜中, 并将银电解质溶液 (100 克/L Ag, pH 12.5) 放入浴缸中。将声波浴设置为室温和功率为 10%. 
		注意: 银电解质溶液是剧毒的, 应格外小心处理。烟雾不应该被吸入. </li>
		<li> 将参考电极的大容量触点连接到恒定的电流源。使用标准连接电缆将计数器电极、银电解液中浸入的银线连接到当前源. </li>
		<li> 将当前源设置为 DC, 并将电流密度设为-4.5 毫安/厘米 2 , 导致银沉积速率约0.3 和 #181; m/分钟启动声波浴, 让电流源运行10分钟. 用 DI 冲洗硅片
		<li> 对于参考电极的氯化, 在声波槽中插入0.1 米氯化钾 (氯化钾) 溶液的容器。将晶片的本体接触和在氯化钾溶液中浸泡的铂电极与恒流源连接. </li>
		<li> 将当前源设置为 DC, 并将电流密度设为 +0.6 毫安/cm 2 , 从而使沉积速率大约为0.075 和 #181; m/分钟启动声波浴, 让当前源运行 7.5 min. </li>
		<li> 冲洗和烘干 PI 晶片, 如步骤1.2.3 中所述. </li>
		<li> 在 uv (365 nm) 曝光300兆焦耳/cm 2 并冲洗并烘干 PI 晶片后, 再按步骤1.2.3 中的描述删除 uv 敏感磁带. </li>
	</ol> </li> <li> 第三个光刻步骤: 使用 DFRs 创建微流体通道. 
	<ol> <li> 将所需的 DFR 层剪切到与硅片 (20 x 20 cm 2 ) 类似的大小。将所需的掩码固定在曝光单元上, 并使用肉眼将 DFR 层对准蒙版。用250兆焦耳/cm 2 UV 光 (365 nm) 照亮抵抗. </li>
		<li> 取下光刻胶的保护箔, 并在1% 碳酸钠 (Na 2 CO 3 ) 中使用标准声波槽 (35 kHz) 预热至42和 #176, 以大约2分钟 (根据结构) 开发抗蚀剂; C 和声波功率100%。为了立即停止反应, 在一个轨道振动筛的 1% HCl 浴中摇动抵抗1分钟。冲洗和干燥每个 DFR 层, 如步骤1.2.3 所述. 
		注: 总共需要处理四 DFR 层, 如步骤1.7 所述: 一个通道层、一个盖层和两个背面层 (防止生物传感器在末端弯曲). </li>
	</ol> </li> <li> 在 PI 衬底上的 DFR 层的分层。
	<ol> <li> 将 PI 晶片放在透明的架空箔上, 并用标准胶带固定。使用相应的对齐结构在显微镜下调整 PI 晶片上的通道 DFR 层. </li>
		<li> 对于层压, 使用标准热辊式贴合机, 并将顶辊预热至100和 #176; c 和底部辊至60和 #176; c. 将压力设置为 3 bar, 向前速度为0.3 米/分. 将晶片与固定的 DFR 层放在层压机的中间启动它;DFR 是通过层压机推的。在将硅片旋转180和 #176 后重复该步骤;. </li>
		<li> 为了防止生物传感器的弯曲, 将两个开发后的背面层层压到硅片上, 步骤 1.8. 1-1. 8.2. </li>
	</ol> </li> <li> 使用疏水阻挡屏障并密封芯片。
	<ol> <li> 从 DFR 通道的前侧卸下保护层将标准胶带放在 DFR 的一端, 向上拉。使用带有0.004 个管的手分配器, 将被溶解的聚四氟乙烯的小水滴分配到绝缘层的井中。要密封微流控芯片, 将盖 DFR 层层压到通道层上, 如步骤1.8 所述. </li>
	</ol> </li> <li> 对微流体传感器进行硬烘烤. 
	<ol> <li> 卸下盖上的所有保护箔和背面 DFR 层。使用普通剪刀把生物传感器切成条。在160和 #176 的烤箱中治疗芯片; C 为 3 h. </li>
	</ol> </li> </ol> 2。片上试验固定化程序 <ol> <li> 在通道的固定区中吸附素. 
	<ol> <li> 准备100和 #181; 在10毫米磷酸盐缓冲盐水 (PBS) 中素溶液, pH 值为 7.4. </li>
		<li> 免除2和 #181; 将素溶液的 L 放到生物传感器的入口. 
		注: 通道由毛细管力填充, 直到流体到达疏水阻挡屏障. </li>
		<li> 确保射流在整个孵化时间内在屏障上不停地停留, 免除2和 #181; 在芯片出口处的 DI 水。将芯片在25和 #176 上孵育; 在封闭容器中, C 为1小时. </li>
		<li> 通过应用真空, 将多余的试剂通过芯片的入口移除。使用50和 #181 清洗通道; 洗涤缓冲器 (PBS 与0.05% 吐温 20), 在真空应用时, 在插座上分配。干燥的渠道, 三十年代, 而真空正在应用. </li>
	</ol> </li> <li> 阻塞通道表面以抑制不绑定. 
	<ol> <li> 在10毫米 PBS 中制备1% 牛血清白蛋白 (BSA) 溶液, pH 值为 7.4. </li>
		<li> 吸管2和 #181; 1% BSA 溶液在入口和2和 #181 上的 l; 在通道出口处的 DI 水。将芯片在25和 #176 上孵育; C 为1小时, 在密闭容器中。去除多余的试剂和干燥的通道, 如步骤2.1.4 所述. </li>
	</ol> </li> <li> 寡标记有生物素和6个家族的 DNA 的孵化。
	<ol> <li> 在10毫米 PBS 中准备不同浓度 (0.001-5 和 #181; M) 的 DNA 溶液, pH 值为 7.4. </li>
		<li> 免除2和 #181; 在入口和2和 #181 上的一个浓度的 DNA 溶液的 l; 出水口的 l。在25和 #176 中孵育芯片; C 为封闭容器中的15分钟. </li>
		<li> 使用额外的生物传感器芯片对其他 DNA 浓度重复步骤 2.3.2. </li>
		<li> 删除多余的试剂和干燥的通道, 如步骤2.1.4 所述. </li>
	</ol> </li> <li> 固定化氧化标记的6抗体。
	<ol> <li> 制定一个5和 #181; 在 10 mM PBS 中, 6 个抗体的浓度, 在 pH 值为 7.4. </li>
		<li> 引入2和 #181; 对入口和2和 #181 的抗体溶液 l; 向通道的出水口。在封闭容器中孵育25和 #176 的标记抗体; C 为15分钟。删除多余的试剂, 如步骤2.1.4 中所述. </li>
	</ol> </li> </ol> 3。使用停止流技术的安培信号检测 <ol> <li> 用于电化学检测的基底溶液的制备. 
	<ol> <li> 在 0.1 M PBS 中制定40毫米葡萄糖溶液, pH 值为 7.4, 超纯水. </li>
		<li> 对于初步处理, 请在超纯水中以7.4 的 pH 值制备0.1 米 PBS 溶液. </li>
	</ol> </li> <li> 对工作电极的初步处理。
	<ol> <li> 使用 custom-made 芯片托架可以方便地放置芯片和一个射流和电连接. </li>
		<li> 将生物传感器电连接到电位。确保微流体通道的射流接触到注射器泵和使用 custom-made 适配器和管的试剂库。启动连接到电位的笔记本电脑, 启动注射器泵控制器, 控制流经芯片的射流流. </li>
		<li> 手动启动注射器泵, 流量为20和 #181 的0.1 米 PBS;在工作电极与芯片上的参考电极, 适用于 5 s 的交流电压为0.8 和-0.05 V 为30周期。在这之后, 使用 0.8 V 的电压在六十年代氧化工作电极. </li>
	使用停止流技术的 </ol> </li> <li> 检测读数。
	<ol> <li> 启动检测信号读数, 等待测量的电流信号稳定。停止注射器泵, 将试剂从0.1 米 PBS 切换到 40 mM 葡萄糖溶液, 并在注射器泵控制器上启动软件;它将自动停止1、2或5分钟的流, 然后重新启动流。观察所产生的当前峰值. 
		注: 对于数据的分析, 可以考虑电流峰值或峰值电荷, 如电化学信号读出模型所描述的 ( 图 2 ). </li>
	</ol>
	</li>
</ol>

<ol>
	<li>Spindel, S., Sapsford, K. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+optical+detection+platforms+for+multiplexed+detection+of+proteins+and+the+need+for+point-of-care+biosensors+for+clinical+use.">Evaluation of optical detection platforms for multiplexed detection of proteins and the need for point-of-care biosensors for clinical use.</a> Sensors (Basel). 14 (12), 22313-22341 (2014).</li><li>Luppa, P. B., Bietenbeck, A., Beaudoin, C., Giannetti, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Clinically+relevant+analytical+techniques,+organizational+concepts+for+application+and+future+perspectives+of+point-of-care+testing.">Clinically relevant analytical techniques, organizational concepts for application and future perspectives of point-of-care testing.</a> Biotechnol Adv. 34 (3), 139-160 (2016).</li><li>Gauglitz, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Point-of-Care+Platforms.">Point-of-Care Platforms.</a> Annu Rev Anal Chem. 7 (1), 297-315 (2014).</li><li>Jung, W., Han, J., Choi, J. W., Ahn, C. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Point-of-care+testing+(POCT)+diagnostic+systems+using+microfluidic+lab-on-a-chip+technologies.">Point-of-care testing (POCT) diagnostic systems using microfluidic lab-on-a-chip technologies.</a> Microelectron Eng. 132, 46-57 (2014).</li><li>Yager, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+diagnostic+technologies+for+global+public+health.">Microfluidic diagnostic technologies for global public health.</a> Nature. 442 (7101), 412-418 (2006).</li><li>Fu, E., Yager, P., Floriano, P. N., Christodoulides, N., McDevitt, J. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Perspective+on+diagnostics+for+global+health.">Perspective on diagnostics for global health.</a> IEEE Pulse. 2 (6), 40-50 (2011).</li><li>Yager, P., Domingo, G. J., Gerdes, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Point-of-care+diagnostics+for+global+health.">Point-of-care diagnostics for global health.</a> Ann Rev Biomed Eng. 10, 107-144 (2008).</li><li>Dincer, C., Bruch, R., Kling, A., Dittrich, P. S., Urban, G. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multiplexed+point-of-care+testing+-+xPOCT.">Multiplexed point-of-care testing - xPOCT.</a> Trends Biotechnol. 35, (2017).</li><li>Horak, J., Dincer, C., Bakirci, H., Urban, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+disposable+dry+film+photoresist-based+microcapillary+immunosensor+chip+for+rapid+detection+of+Epstein-Barr+virus+infection.">A disposable dry film photoresist-based microcapillary immunosensor chip for rapid detection of Epstein-Barr virus infection.</a> Sens Actuators B Chem. 191, 813-820 (2014).</li><li>Jobst, G., Gamp, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Method+for+the+fabrication+of+a+&amp;#34;lab+on+chip&amp;#34;+from+photoresist+material+for+medical+diagnostic+applications.">Method for the fabrication of a &amp;#34;lab on chip&amp;#34; from photoresist material for medical diagnostic applications.</a> US patent. , (2010).</li><li>Kling, A., Dincer, C., Armbrecht, L., Horak, J., Kieninger, J., Urban, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrochemical+microfluidic+platform+for+simultaneous+multi-analyte+detection.">Electrochemical microfluidic platform for simultaneous multi-analyte detection.</a> Procedia Eng. 120, 916-919 (2015).</li><li>Armbrecht, L., Dincer, C., Kling, A., Horak, J., Kieninger, J., Urban, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Self-assembled+magnetic+bead+chains+for+sensitivity+enhancement+of+microfluidic+electrochemical+biosensor+platforms.">Self-assembled magnetic bead chains for sensitivity enhancement of microfluidic electrochemical biosensor platforms.</a> Lab Chip. 15, 4314-4321 (2015).</li><li>Dincer, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Designed+miniaturization+of+microfluidic+biosensor+platforms+using+the+stop-flow+technique.">Designed miniaturization of microfluidic biosensor platforms using the stop-flow technique.</a> Analyst. 141, 6073-6079 (2016).</li><li>Weltin, A., Kieninger, J., Enderle, B., Gellner, A. K., Fritsch, B., Urban, G. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polymer-based,+flexible+glutamate+and+lactate+microsensors+for+in+vivo+applications.">Polymer-based, flexible glutamate and lactate microsensors for in vivo applications.</a> Biosens Bioelectron. 61, 192-199 (2014).</li><li>Kling, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multianalyte+Antibiotic+Detection+on+an+Electrochemical+Microfluidic+Platform.">Multianalyte Antibiotic Detection on an Electrochemical Microfluidic Platform.</a> Anal Chem. 88 (20), 10036-10043 (2016).</li><li>Bruch, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Clinical+on-site+monitoring+of+&#223;-lactam+antibiotics+for+a+personalized+antibiotherapy.">Clinical on-site monitoring of &#223;-lactam antibiotics for a personalized antibiotherapy.</a> Sci Rep. , (2017).</li><li>Horak, J., Dincer, C., Qelibari, E., Bakirci, H., Urban, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polymer-modified+microfluidic+immunochip+for+enhanced+electrochemical+detection+of+troponin+i.">Polymer-modified microfluidic immunochip for enhanced electrochemical detection of troponin i.</a> Sens Actuators B Chem. 209, 478-485 (2015).</li><li>Horak, J., Dincer, C., Bakirci, H., Urban, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sensitive,+rapid+and+quantitative+detection+of+substance+P+in+serum+samples+using+an+integrated+microfluidic+immunochip.">Sensitive, rapid and quantitative detection of substance P in serum samples using an integrated microfluidic immunochip.</a> Biosens Bioelectron. 58, 186-192 (2014).</li><li>Mattox, D. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Handbook of Physical Vapor Deposition (PVD) Processing. , (2010).</li></ol>

作者没有什么可透露的。

在这里提出的用于制造微流体电化学生物传感器的协议, 使开发一个低成本, 紧凑, 易于使用的平台, 用于检测分子。根据随后在生物传感器上使用的化验, 可以检测到几种不同的生物标志物。这使得该平台非常通用, 可以广泛地访问各种应用程序领域, 从标准诊断测试 (例如,确定医生办公室的特定疾病的存在) 到点应用程序 (例如,对患者进行治疗性药物监测以进行个体化药物治疗)。特?...

在过去20年中, 诊断应用已成为 in-depth 研究全球公共卫生发展的基础。传统上, 实验室诊断工具用于检测疾病。尽管它们在疾病诊断方面仍然发挥着关键作用, 但在病人或病人附近进行的点试验 (POCT) 近年来已变得越来越普遍。特别是在需要立即治疗的情况下, 如急性心肌梗塞或糖尿病监测, 临床发现的快速确认是必不可少的。因此, 越来越需要 POCT 设备, 可以由非操作, 并且同时能够在短时间内执行精确的体外诊断测试,1,2,3,4.
在 POCT 领域已经取得了显著的进步。但是, 仍有许多挑战需要克服5、6、7、8。为了使 POCT 平台能够成功地投放市场并具有实验室诊断的竞争力, 该设备必须严格满足以下要求: (i) 提供与实验室相符的精确和定量的测试结果结果;(ii) 有较短的 sample-to-result 时间, 使病人可立即接受治疗;(iii) 功能简单, 易于操作, 即使由未经训练的个人操作, 并需要尽量减少用户干预;(iv) 由一个低成本的传感器单元组成, 用于一次性应用。此外, 无设备诊断是有利的, 主要在资源贫乏的环境中3,4,6。
由于这些苛刻的要求, 只有两个基于电化学检测的 POCT 系统 (例如,血糖试纸) 和侧流免疫 (例如,家庭妊娠测试) 已经成功投放市场, 以便远.然而, 这两个系统都有缺点, 如性能不佳 (即,血糖监测有不准确的测试结果和侧流分析只提供定性 (阳性或阴性) 测量结果)4, 6。传统的 POCT 系统的这些缺点导致了对开发新技术的需求不断增加, 这些技术提供了快速、低成本和定量检测, 在4,5。
为了应对 POCT 设备面临的这些挑战, DFR 技术最近被用于制造一次性和低成本的生物传感器9,10,11,12,13,14. 与软、液体平版印刷材料相比, 如 SU-8、DFRs 等, 具有许多优点: 它们 (i) 有多种组合物和厚度 (从几微米到几毫米);(ii) 有一个非常粗糙的表面积, 便于与各种材料粘合;(iii) 具有优异的厚度均匀性;(iv) 为大规模生产提供廉价、轻便和高通量的制造;(五) 容易用各种低成本的工具切割, 像一把简单的剪刀;和 (vi) 允许创建三维结构, 如微流控通道, 通过堆叠在彼此顶部的多个 DFR 层。
另一方面, DFRs 一般有一个相对较差的分辨率相比, 液体光刻, 这主要是由薄膜厚度和增加距离之间的面具和 DFR 由于保护箔, 这还使光散射.然而, 对于集成微流体传感器的制造, DFRs 是非常适合低成本的大规模生产。
因此, 我们在本工作中介绍了一种 DFR-based 电化学微流控生物传感器的制备和应用。详细的协议描述了生物传感器平台的每一个生产步骤, dna 模型检测的片上固定, 以及使用停止流技术的电化学读出。这个通用平台能够检测多种生物分子, 使用不同的化验技术 (例如,基因组学, cellomics, 蛋白质组学) 或化验格式 (例如,竞争性, 三明治, 或直接)。基于这样一个 DFR 平台, 我们的小组以前成功地证明了各种各样的分析的快速和敏感的定量, 包括抗生素13,15,16 (四环素,pristinamycin, 和？内酰胺抗生素), 肌钙蛋白 i17, 和物质 P18。

<table><tbody><tr><td>&lt;strong&gt;Material&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>Pyralux</td><td>DuPont</td><td>AP8525R</td><td>Used as polyimide substrate</td></tr><tr><td>MA-N 1420</td><td>Micro Resist Technology</td><td>MA-N1420</td><td>Lift-off resit to define the platinum depostion</td></tr><tr><td>Ma-D 533s</td><td>Micro Resist Technology</td><td>MaD533S</td><td>Developer for MA-N1420</td></tr><tr><td>Platinum</td><td>-</td><td>-</td><td>Electrode and contact pad material</td></tr><tr><td>Ma-R 404s</td><td>Micro Resist Technology</td><td>MaR404S</td><td>Remover for MA-N1420</td></tr><tr><td>SU-8 3005</td><td>MicroChem Corp.</td><td>SU-8-3005</td><td>Photoresist to define the electrode area and as insulation</td></tr><tr><td>1-methoxy-2-propanol acetate</td><td>Sigma-Aldrich</td><td>108-65-6</td><td>Developer for SU-8 3005</td></tr><tr><td>2-Propanol</td><td>VWR</td><td>8.18766.2500</td><td>Removing of the SU-8 developer</td></tr><tr><td>1020R</td><td>Ultron Systems Inc.</td><td>1020R</td><td>UV sensitive adhesive tape for protection of contact pads</td></tr><tr><td>Arguna S</td><td>Degussa</td><td>1935</td><td>For Silver depostion on reference electrode</td></tr><tr><td>KCl</td><td>Methrom</td><td>62308.020</td><td>For chloridation of the silver reference electrode</td></tr><tr><td>Pyralux</td><td>DuPont</td><td>PC1025</td><td>Dry film photoresist</td></tr><tr><td>Sodium carbonat</td><td>Fluka</td><td>71352</td><td>Developer for Pyralux PC1025</td></tr><tr><td>Hydrogen chloride</td><td>Sigma-Aldrich</td><td>30720</td><td>To top the development of the DFR</td></tr><tr><td>Teflon AF 1600</td><td>DuPont</td><td>AF1600</td><td>For employing the stopping barrier</td></tr><tr><td>&lt;strong&gt;Name&lt;/strong&gt;</td><td>&lt;strong&gt;Company&lt;/strong&gt;</td><td>&lt;strong&gt;Catalog Number&lt;/strong&gt;</td><td>&lt;strong&gt;Comments&lt;/strong&gt;</td></tr><tr><td>&lt;strong&gt;Equipment&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>PA104</td><td>Mega Electronics</td><td>-</td><td>Bubble etch tank</td></tr><tr><td>FED 53</td><td>Binder</td><td>9010-0018</td><td>Oven</td></tr><tr><td>SPIN150</td><td>APT</td><td>-</td><td>Spin coater</td></tr><tr><td>Pr&amp;auml;zitherm</td><td>Harry Gestigkeit GmbH</td><td>PZ 28-2</td><td>Hot plate</td></tr><tr><td>Hellas</td><td>Bungard Elektronik</td><td>40000</td><td>Exposure unit</td></tr><tr><td>Tetra30-LF-PC</td><td>Diener</td><td>-</td><td>Plasma unit</td></tr><tr><td>Univex 500</td><td>Leybold</td><td>-</td><td>Physical vapor deposition unit</td></tr><tr><td>Shaker S4</td><td>ELMI</td><td>-</td><td>Orbital shaker</td></tr><tr><td>Sonorex Super 10 P</td><td>Bandelin</td><td>783</td><td>Sonic bath</td></tr><tr><td>6221 DC and AC</td><td>Keithley</td><td>-</td><td>Current source</td></tr><tr><td>HRL 350</td><td>Ozatec</td><td>-</td><td>Laminator unit</td></tr><tr><td>Vaccum pen</td><td>EFD</td><td>-</td><td>Vacuum pen</td></tr></tbody></table>

dry film photoresist-based electrochemical microfluidic biosensor platform: device fabrication, on-chip assay preparation, and system operation

近年来, 生物标志物诊断成为诊断人类疾病的不可或缺的工具, 特别是对点诊断。一个易于使用和低成本的传感器平台是非常理想的测量各种类型的分析 (例如,生物标记物, 激素, 和药物) 定量和具体。由于这个原因, 干膜光刻胶技术-使廉价, 轻便, 和高通量制造-被用于制造微流体生物传感器在这里提出。根据随后使用的生物测定, 多功能平台能够检测各种类型的生物分子。在制造的设备, 铂电极是结构在一个灵活的聚酰亚胺 (PI) 箔在唯一的洁净室工艺步骤。PI 箔担当基体为电极, 用氧抗蚀剂绝缘。微流控通道随后由干膜光刻胶 (DFR) 箔在 PI 晶片上的发展和层压产生。通过在通道中使用疏水阻挡屏障, 将该通道分为两个特定区域: 酶链法的固定化切片和安培信号读出的电化学测量单元。
通过生物分子对通道表面的吸附, 进行了片上生物测定的固定化。葡萄糖氧化酶是一种用于电化学信号产生的传感器。在基体的存在下, 葡萄糖, 过氧化氢被生产, 在白金工作电极被发现。在快速检测的同时, 采用了停止流技术来获得信号放大。通过引入微流控系统, 可以定量地测量不同的生物分子, 从而指示不同类型的疾病, 或在治疗药物监测方面, 促进个性化治疗。

微流控生物传感器平台的设计与制作:
采用多 DFR 层的标准光刻技术, 在晶片级上实现了微流体生物传感器芯片的制备。这种制作策略依赖于铂图案的 PI 基底上的 DFRs 层的分层, 形成微流控通道。在图 1中给出了描述不同制造步骤的简短摘要。一个单一的6个晶片包括130微流控生物传感器, 每一个尺寸为 8 x 10 mm...

Watch this Scientific Journal Video about Dry Film Photoresist-based Electrochemical Microfluidic Biosensor Platform: Device Fabrication, On-chip Assay Preparation, and System Operation at JoVE.com

Dry Film Photoresist-based Electrochemical Microfluidic Biosensor Platform: Device Fabrication, On-chip Assay Preparation, and System Operation

干膜 Photoresist-based 电化学微流控生物传感器平台: 器件制备、片上检测制备及系统运行

利用低成本干膜光刻胶技术对各种分析进行快速、灵敏的定量化设计, 制备了微流控生物传感器平台。这种一次性系统允许通过停止流动技术在片上固定的酶联用的电化学读出。

In recent years, biomarker diagnostics became an indispensable tool for the diagnosis of human disease, especially for the point-of-care diagnostics. An ...

dry-film-photoresist-based-electrochemical-microfluidic-biosensor

Universidad de Cartagena UDEC

Research

JoVE Journal

Bioengineering

11.6K 次观看.  University of Freiburg. 利用低成本干膜光刻胶技术对各种分析进行快速、灵敏的定量化设计, 制备了微流控生物传感器平台。这种一次性系统允许通过停止流动技术在片上固定的酶联用的电化学读出。

视频: Dry Film Photoresist-based Electrochemical Microfluidic Biosensor Platform: Device Fabrication, On-chip Assay Preparation, and System Operation

Microfluidic On-chip Capture-cycloaddition Reaction to Reversibly Immobilize Small Molecules or Multi-component Structures for Biosensor Applications

Methods for rapid surface immobilization of bioactive small molecules with control over orientation and immobilization density are highly desirable for biosensor and microarray applications. In this Study, we use a highly efficient covalent bioorthogonal [4+2] cycloaddition reaction between trans-cyclooctene (TCO) and 1,2,4,5-tetrazine (Tz) to enable the microfluidic immobilization of TCO/Tz-derivatized molecules. We monitor the process in real-time under continuous flow conditions using surface plasmon resonance (SPR). To enable reversible immobilization and extend the experimental range of the sensor surface, we combine a non-covalent antigen-antibody capture component with the cycloaddition reaction. By alternately presenting TCO or Tz moieties to the sensor surface, multiple capture-cycloaddition processes are now possible on one sensor surface for on-chip assembly and interaction studies of a variety of multi-component structures. We illustrate this method with two different immobilization experiments on a biosensor chip; a small molecule, AP1497 that binds FK506-binding protein 12 (FKBP12); and the same small molecule as part of an immobilized and in situ-functionalized nanoparticle.

We present a method for rapid, reversible immobilization of small molecules and functionalized nanoparticle assemblies for Surface Plasmon Resonance (SPR) studies, using sequential on-chip bioorthogonal cycloaddition chemistry and antibody-antigen capture.

微流控芯片上捕获环加成反应可逆地固定小分子或多组分结构的生物传感器应用

Methods  for rapid surface immobilization of bioactive small molecules with control over  orientation and immobilization density are highly desirable for ...

科研

化学

Fluorescence detection methods for microfluidic droplet platforms

The development of microfluidic platforms for performing chemistry and biology has in large part been driven by a range of potential benefits that accompany system miniaturisation. Advantages include the ability to efficiently process nano- to femoto- liter volumes of sample, facile integration of functional components, an intrinsic predisposition towards large-scale multiplexing, enhanced analytical throughput, improved control and reduced instrumental footprints.1
In recent years much interest has focussed on the development of droplet-based (or segmented flow) microfluidic systems and their potential as platforms in high-throughput experimentation.2-4 Here water-in-oil emulsions are made to spontaneously form in microfluidic channels as a result of capillary instabilities between the two immiscible phases. Importantly, microdroplets of precisely defined volumes and compositions can be generated at frequencies of several kHz. Furthermore, by encapsulating reagents of interest within isolated compartments separated by a continuous immiscible phase, both sample cross-talk and dispersion (diffusion- and Taylor-based) can be eliminated, which leads to minimal cross-contamination and the ability to time analytical processes with great accuracy. Additionally, since there is no contact between the contents of the droplets and the channel walls (which are wetted by the continuous phase) absorption and loss of reagents on the channel walls is prevented.
Once droplets of this kind have been generated and processed, it is necessary to extract the required analytical information. In this respect the detection method of choice should be rapid, provide high-sensitivity and low limits of detection, be applicable to a range of molecular species, be non-destructive and be able to be integrated with microfluidic devices in a facile manner. To address this need we have developed a suite of experimental tools and protocols that enable the extraction of large amounts of photophysical information from small-volume environments, and are applicable to the analysis of a wide range of physical, chemical and biological parameters. Herein two examples of these methods are presented and applied to the detection of single cells and the mapping of mixing processes inside picoliter-volume droplets. We report the entire experimental process including microfluidic chip fabrication, the optical setup and the process of droplet generation and detection.

Droplet-based microfluidic platforms are promising candidates for high throughput experimentation since they are able to generate picoliter, self-compartmentalized vessels inexpensively at kHz rates. Through integration with fast, sensitive and high resolution fluorescence spectroscopic methods, the large amounts of information generated within these systems can be efficiently extracted, harnessed and utilized.

荧光检测方法，为微流体液滴平台

The development of microfluidic platforms for performing chemistry and biology has in large part been driven by a range of potential benefits that ...

生物工程

A Microfluidic Chip for the Versatile Chemical Analysis of Single Cells

We present a microfluidic device that enables the quantitative determination of intracellular biomolecules in multiple single cells in parallel. For this purpose, the cells are passively trapped in the middle of a microchamber. Upon activation of the control layer, the cell is isolated from the surrounding volume in a small chamber. The surrounding volume can then be exchanged without affecting the isolated cell. However, upon short opening and closing of the chamber, the solution in the chamber can be replaced within a few hundred milliseconds. Due to the reversibility of the chambers, the cells can be exposed to different solutions sequentially in a highly controllable fashion, e.g. for incubation, washing, and finally, cell lysis. The tightly sealed microchambers enable the retention of the lysate, minimize and control the dilution after cell lysis. Since lysis and analysis occur at the same location, high sensitivity is retained because no further dilution or loss of the analytes occurs during transport. The microchamber design therefore enables the reliable and reproducible analysis of very small copy numbers of intracellular molecules (attomoles, zeptomoles) released from individual cells. Furthermore, many microchambers can be arranged in an array format, allowing the analysis of many cells at once, given that suitable optical instruments are used for monitoring. We have already used the platform for proof-of-concept studies to analyze intracellular proteins, enzymes, cofactors and second messengers in either relative or absolute quantifiable manner.

In this article we present a microfluidic chip for single cell analysis. It allows the quantification of intracellular proteins, enzymes, cofactors, and second messengers by means of fluorescent assays or immunoassays.&#160;

一个微流控芯片单细胞的多功能化学分析

We present a microfluidic device that enables the quantitative determination of intracellular biomolecules in multiple single cells in parallel. For this ...

A Microfluidic-based Electrochemical Biochip for Label-free DNA Hybridization Analysis

Miniaturization of analytical benchtop procedures into the micro-scale provides significant advantages in regards to reaction time, cost, and integration of pre-processing steps. Utilizing these devices towards the analysis of DNA hybridization events is important because it offers a technology for real time assessment of biomarkers at the point-of-care for various diseases. However, when the device footprint decreases the dominance of various physical phenomena increases. These phenomena influence the fabrication precision and operation reliability of the device. Therefore, there is a great need to accurately fabricate and operate these devices in a reproducible manner in order to improve the overall performance. Here, we describe the protocols and the methods used for the fabrication and the operation of a microfluidic-based electrochemical biochip for accurate analysis of DNA hybridization events. The biochip is composed of two parts: a microfluidic chip with three parallel micro-channels made of polydimethylsiloxane (PDMS), and a 3 x 3 arrayed electrochemical micro-chip. The DNA hybridization events are detected using electrochemical impedance spectroscopy (EIS) analysis. The EIS analysis enables monitoring variations of the properties of the electrochemical system that are dominant at these length scales. With the ability to monitor changes of both charge transfer and diffusional resistance with the biosensor, we demonstrate the selectivity to complementary ssDNA targets, a calculated detection limit of 3.8 nM, and a 13% cross-reactivity with other non-complementary ssDNA following 20 min&#160;of incubation. This methodology can improve the performance of miniaturized devices by elucidating on the behavior of diffusion at the micro-scale regime and by enabling the study of DNA hybridization events.

We present a microfluidic-based electrochemical biochip for DNA hybridization detection. Following ssDNA probe functionalization, the specificity, sensitivity, and detection limit are studied with complementary and non-complementary ssDNA targets. Results illustrate the influence of the DNA hybridization events on the electrochemical system, with a detection limit of 3.8 nM.

微流体为基础的电化学生物芯片的无标记的DNA杂交分析

Miniaturization of analytical benchtop procedures into the micro-scale provides significant advantages in regards to reaction time, cost, and integration ...

A Microfluidic Platform for Precision Small-volume Sample Processing and Its Use to Size Separate Biological Particles with an Acoustic Microdevice

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. However, to achieve robust sample manipulation it is necessary to address device integration with the macroscale environment. To realize repeatable, sensitive particle separation with microfluidic devices, this protocol presents a complete automated and integrated microfluidic platform that enables precise processing of 0.15&#8211;1.5 ml samples using microfluidic devices. Important aspects of this system include modular device layout and robust fixtures resulting in reliable and flexible world to chip connections, and fully-automated fluid handling which accomplishes closed-loop sample collection, system cleaning and priming steps to ensure repeatable operation. Different microfluidic devices can be used interchangeably with this architecture. Here we incorporate an acoustofluidic device, detail its characterization, performance optimization, and demonstrate its use for size-separation of biological samples. By using real-time feedback during separation experiments, sample collection is optimized to conserve and concentrate sample. Although requiring the integration of multiple pieces of equipment, advantages of this architecture include the ability to process unknown samples with no additional system optimization, ease of device replacement, and precise, robust sample processing.

This protocol describes a system architecture for performing automated small volume (0.15&#8211;1.5 ml) particle separations using a microfluidic device, and discusses methods to optimize acoustofluidic device performance and operation.

微流体平台精密小批量来样加工及它的使用尺寸分离生物颗粒的声微型

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. ...

Digital Microfluidics for Automated Proteomic Processing

Clinical proteomics has emerged as an important new discipline, promising the discovery of biomarkers that will be useful for early diagnosis and prognosis of disease. While clinical proteomic methods vary widely, a common characteristic is the need for (i) extraction of proteins from extremely heterogeneous fluids (i.e. serum, whole blood, etc.) and (ii) extensive biochemical processing prior to analysis. Here, we report a new digital microfluidics (DMF) based method integrating several processing steps used in clinical proteomics. This includes protein extraction, resolubilization, reduction, alkylation and enzymatic digestion. Digital microfluidics is a microscale fluid-handling technique in which nanoliter-microliter sized droplets are manipulated on an open surface. Droplets are positioned on top of an array of electrodes that are coated by a dielectric layer - when an electrical potential is applied to the droplet, charges accumulate on either side of the dielectric. The charges serve as electrostatic handles that can be used to control droplet position, and by biasing a sequence of electrodes in series, droplets can be made to dispense, move, merge, mix, and split on the surface. Therefore, DMF is a natural fit for carrying rapid, sequential, multistep, miniaturized automated biochemical assays. This represents a significant advance over conventional methods (relying on manual pipetting or robots), and has the potential to be a useful new tool in clinical proteomics.
Mais J. Jebrail, Vivienne N. Luk, and Steve C. C. Shih contributed equally to this work.
Sergio L. S. Freire's current address is at the University of the Sciences in Philadelphia located at 600 South 43rd Street, Philadelphia, PA 19104.

Digital Microfluidics is a technique characterized by the manipulation of discrete droplets (~nL - mL) on an array of electrodes by the application of electrical fields. It is well-suited for carrying out rapid, sequential, miniaturized automated biochemical assays. Here, we report a platform capable of automating several proteomic processing steps.

数字微流体进行自动蛋白质组学处理

Clinical proteomics has emerged as an important new discipline, promising the discovery of biomarkers that will be useful for early diagnosis and ...

生物学

Fabrication of Three-dimensional Paper-based Microfluidic Devices for Immunoassays

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and directed within a layer of paper. Moreover, stacking multiple layers of patterned paper creates sophisticated three-dimensional microfluidic networks that can support the development of analytical and bioanalytical assays. Paper-based microfluidic devices are inexpensive, portable, easy to use, and require no external equipment to operate. As a result, they hold great promise as a platform for point-of-care diagnostics. In order to properly evaluate the utility and analytical performance of paper-based devices, suitable methods must be developed to ensure their manufacture is reproducible and at a scale that is appropriate for laboratory settings. In this manuscript, a method to fabricate a general device architecture that can be used for paper-based immunoassays is described. We use a form of additive manufacturing (multi-layer lamination) to prepare devices that comprise multiple layers of patterned paper and patterned adhesive. In addition to demonstrating the proper use of these three-dimensional paper-based microfluidic devices with an immunoassay for human chorionic gonadotropin (hCG), errors in the manufacturing process that may result in device failures are discussed. We expect this approach to manufacturing paper-based devices will find broad utility in the development of analytical applications designed specifically for limited-resource settings.

We detail a method to fabricate three-dimensional paper-based microfluidic devices for use in the development of immunoassays. Our approach to device assembly is a type of multilayer, additive manufacturing. We demonstrate a sandwich immunoassay to provide representative results for these types of paper-based devices.

三维纸基微流体装置的制造用于免疫分析

Paper wicks fluids autonomously due to capillary action. By patterning paper with hydrophobic barriers, the transport of fluids can be controlled and ...

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to spatially fractionate the sample based on a biological property of interest. For the resultant spatial distribution to be used as the assay readout, microfluidic devices are often subjected to microscopic analysis requiring complex instrumentation with higher cost and reduced portability. To address this limitation, we have developed an integrated electronic sensing technology for multiplexed detection of particles at different locations on a microfluidic chip. Our technology, called Microfluidic CODES, combines Resistive Pulse Sensing with Code Division Multiple Access to compress 2D spatial information into a 1D electrical signal. In this paper, we present a practical demonstration of the Microfluidic CODES technology to detect and size cultured cancer cells distributed over multiple microfluidic channels. As validated by the high-speed microscopy, our technology can accurately analyze dense cell populations all electronically without the need for an external instrument. As such, the Microfluidic CODES can potentially enable low-cost integrated lab-on-a-chip devices that are well suited for the point-of-care testing of biological samples.

We demonstrate a microfluidic platform with an integrated surface electrode network that combines resistive pulse sensing (RPS) with code division multiple access (CDMA), to multiplex detection and sizing of particles in multiple microfluidic channels.

与复用电子检测的粒子的空间跟踪微流体平台

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to ...

Fabrication and Validation of an Organ-on-chip System with Integrated Electrodes to Directly Quantify Transendothelial Electrical Resistance

Organs-on-chips, in vitro models involving the culture of (human) tissues inside microfluidic devices, are rapidly emerging and promise to provide useful research tools for studying human health and disease. To characterize the barrier function of cell layers cultured inside organ-on-chip devices, often transendothelial or transepithelial electrical resistance (TEER) is measured. To this end, electrodes are usually integrated into the chip by micromachining methods to provide more stable measurements than is achieved with manual insertion of electrodes into the inlets of the chip. However, these electrodes frequently hamper visual inspection of the studied cell layer or require expensive cleanroom processes for fabrication. To overcome these limitations, the device described here contains four easily integrated electrodes that are placed and fixed outside of the culture area, making visual inspection possible. Using these four electrodes the resistance of six measurement paths can be quantified, from which the TEER can be directly isolated, independent of the resistance of culture medium-filled microchannels. The blood-brain barrier was replicated in this device and its TEER was monitored to show the device applicability. This chip, the integrated electrodes and the TEER determination method are generally applicable in organs-on-chips, both to mimic other organs or to be incorporated into existing organ-on-chip systems.

This publication describes the fabrication of an organ-on-chip device with integrated electrodes for direct quantification of transendothelial electrical resistance (TEER). For validation, the blood-brain barrier was mimicked inside this microfluidic device and its barrier function was monitored. The presented methods for electrode integration and direct TEER quantification are generally applicable.

用集成电极直接量化 Transendothelial 电阻的 Organ-on-chip 系统的制作与验证

Organs-on-chips, in vitro models involving the culture of (human) tissues inside microfluidic devices, are rapidly emerging and promise to provide useful ...

Electrowetting-based Digital Microfluidics Platform for Automated Enzyme-linked Immunosorbent Assay

Electrowetting is the effect by which the contact angle of a droplet exposed to a surface charge is modified. Electrowetting-on-dielectric (EWOD) exploits the dielectric properties of thin insulator films to enhance the charge density and hence boost the electrowetting effect. The presence of charges results in an electrically induced spreading of the droplet which permits purposeful manipulation across a hydrophobic surface. Here, we demonstrate EWOD-based protocol for sample processing and detection of four categories of antigens, using an automated surface actuation platform, via two variations of an Enzyme-Linked Immunosorbent Assay (ELISA) methods. The ELISA is performed on magnetic beads with immobilized primary antibodies which can be selected to target a specific antigen. An antibody conjugated to HRP binds to the antigen and is mixed with H2O2/Luminol for quantification of the captured pathogens. Assay completion times of between 6 and 10 min were achieved, whilst minuscule volumes of reagents were utilized.

Electrowetting-based digital microfluidic is a technique that utilizes a voltage-driven change in the apparent contact angle of a microliter-volume droplet to facilitate its manipulation. Combining this with functionalized magnetic beads enables the integration of multiple laboratory unit operations for sample preparation and identification of pathogens using Enzyme-linked Immunosorbent Assay (ELISA).

基于电润的数字微流体平台，用于自动酶链接免疫吸附测定

Electrowetting is the effect by which the contact angle of a droplet exposed to a surface charge is modified. Electrowetting-on-dielectric (EWOD) exploits ...